General Electric Washer WJSR4160D5CC Leaking

Replacement drain hose for top-load washers. Connects washer to household drainage system. Replace if cracked, leaking, crushed, or missing.

The Drain Hose Clip is an OEM part for GE washing machines. It secures the drain hose to the back of the washer, preventing it from becoming dislodged during operation. This ensures that water is properly directed out of the washer and into the household drain system, preventing leaks and water damage.

Causes of a bad drain hose clip can include wear and tear from regular use, damage from improper handling during installation or maintenance, or breakage due to repeated stress and movement of the washer.

Symptoms of a bad drain hose clip include:

• Water leaking from the back of the washer
• Drain hose detaching or becoming loose during operation
• Difficulty securing the drain hose in place
• Visible damage or cracking on the clip

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Note: For the entire drain hose, use part number WH41X10096.

Drain pump inlet hose for top-load washers. Connects the tub to the pump assembly. Replace if cracked, leaking, or has holes causing water on the floor.

Prevents water leaks between the washer tub and transmission. Replace if you notice water leaking from the base during wash cycles. Verify fit by model.

If your washer won't fill, overfills, or leaks when off, the water inlet valve may be faulty. Simple 10-20 minute DIY repair with basic tools.

Washer won't drain or leaves clothes soaking wet? This drain pump removes water from the tub after each cycle. Typical DIY repair takes 20-30 minutes.

This tub-bearing split ring is an OEM replacement part designed for GE washing machines. This part measures 2 inches in diameter. It is positioned between the inner and outer tubs to hold the tub bearing inside the outer tub. The Tub Bearing Split Ring not only supports the tub/hub assembly but also ensures smooth operation. 

Symptoms of a bad Tub Bearing Split Ring include:

• Excessive vibration or tub imbalance during spins  
• Loud clunking, knocking or grinding sounds  
• Reduced spin speeds or inability to achieve high RPMs
• Premature tub or bearing wear requiring replacement

Causes can be extended use over time which leads to wear and fatigue of the split ring material. Cracks or breaks can develop, reducing its stability and load-bearing capacity.

This genuine GE replacement part is also compatible with Hotpoint, RCA and some Kenmore front-load models. 

NOTE: For the washer outer tub seal order WH02X10383.

Replacement tub bearing for top-load washers. Fixes grinding, roaring, or loud humming noises during spin cycles. Verify fit with your model number.

Hub washer fits between the transmission and inner tub in top-load washers. Replace if cracked, worn, or causing leaks during operation.

Guides water from the inlet valve into the wash tub. Replace if cracked, broken, leaking, or causing uneven water distribution in your top-load washer.

The Drain Hose is an OEM part for GE washing machines. It is specifically designed to channel used water out of the washer and into the household drainage system. 

Causes of a bad drain hose can include physical damage from movement or installation, clogging from lint and debris, or degradation of the hose material over time, leading to leaks and inefficiency.

Symptoms of a bad Drain Hose include:

• Water leaking from the back or underside of the washing machine
• Pools of water around the area where the washing machine is installed
• Signs of wear or damage to the hose, such as cracks, holes, or bulging

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Supports the inner tub for smooth rotation during wash and spin cycles. Replace if you hear loud grinding noise or see oil stains. Verify fit by model.

Connects the pressure switch to the tub in top-load washers. Replace if cracked, punctured, or brittle to restore proper water level monitoring.

Secures washer hoses at pump, tub, and valve connections to prevent leaks and hose blow-offs. Replace worn or missing clamps for a tight seal. Confirm fit.

Seals the flood/overflow hose connection to your washer tub. Replace if water seeps from the tub area or the gasket feels soft. Confirm fit by model.

Secures your washer's drain hose to the standpipe or laundry tub. Replace if cracked, broken, or missing to keep hose positioned and prevent dislodging.

Replaces a cracked or leaking wash tub to restore water containment and drum support. Fixes leaks, rubbing noises, and vibration. Confirm fit by model.