Parts for Ge AEQ12DMG1: 01 - Room Air Conditioner Parts

This thermostat is the temperature control for room air conditioners. It senses temperature and cycles the compressor to maintain your set comfort level, helping restore consistent cooling when the original control becomes inaccurate or fails. What it does:

• Monitors temperature and opens/closes contacts to start and stop the compressor
• Helps the unit reach and maintain the temperature you select
• Helps resolve symptoms such as: AC won't turn on/off at the dial setting, runs continuously, short-cycles, or temperature adjustments have little effect
• Direct-fit replacement designed for the original mounting location

• 1 thermostat

• Disconnect power before servicing to avoid electrical shock
• Access the control panel; note wire locations and transfer any mounting hardware from the old part
• If your model uses a capillary sensing tube, route it exactly as original and secure in clips; do not kink or sharply bend it
• Reassemble, align the control knob, and test operation across several temperature settings

This replacement transformer supplies the correct voltage for an appliance's control circuits so electronic controls and low-voltage components receive stable power. Installs in place of a failed or damaged transformer to restore reliable control operation. What it does:

• Converts incoming mains power to the lower voltage used by control boards and low-voltage components
• Restores power to electronic controls and displays when a failed transformer prevents operation
• Helps resolve symptoms like dead control panels, no display, or intermittent control function
• Provides a direct, plug-in replacement for the corresponding OEM transformer

• Disconnect power to the appliance before starting any repair to avoid electric shock
• Label or photograph wire connections before removal to ensure correct reassembly
• Mount securely and reconnect wires exactly as original; use appropriate wire connectors

This replacement fan motor restores proper airflow in your appliance, helping cool components and maintain efficient operation. It's a direct-fit motor designed to replace a worn or failed fan motor and reduce noise or performance issues. What it does:

• Circulates air through the appliance to support cooling and temperature regulation
• Replaces a motor that has stopped running or runs intermittently
• Helps stop abnormal noise caused by a failing fan motor
• Reduces overheating or poor cooling tied to inadequate airflow

• Disconnect power to the appliance before beginning any repair
• Match the part number and mounting orientation before removing the old motor
• Handle wiring connectors carefully and secure all fasteners during reassembly

This axial flow fan circulates air inside the appliance to help cool components and maintain proper ventilation. It replaces a worn or damaged blower wheel to restore airflow and reduce overheating risk. What it does:

• Moves air across coils or internal components to support cooling and ventilation.
• Helps prevent overheating and supports consistent appliance performance.
• Can reduce unusual temperature-related symptoms or poor cooling/airflow.
• Fits into the appliance's blower/motor assembly to restore proper airflow.

• Disconnect power to the appliance before starting any repair.
• Handle the fan blades carefully to avoid bending or damage.
• Verify proper seating on the motor shaft and secure fasteners per the appliance's service instructions.

This flat washer provides a secure, even load distribution for a fastener on the appliance, helping maintain proper assembly and reduce loosening or wear. Use it to replace a damaged or missing washer during repairs. What it does:

• Sits under a nut or bolt to spread load and protect the appliance surface
• Helps prevent fasteners from loosening due to vibration
• Restores proper spacing and alignment for connected parts
• Commonly replaced when you see corrosion, cracking, or a loose connection

• One flat washer

• Disconnect power and turn off water supply before starting any repair
• Tighten fasteners to a snug fit—avoid over-tightening which can crush the washer
• If adjacent parts show damage or corrosion, inspect and replace as needed

This nut with attached washer is a small securing fastener used to clamp appliance parts and prevent loosening. It provides a low-profile, integrated washer bearing surface for a reliable hold. What it does:

• Secures panels, brackets, or components to prevent movement and rattling
• Maintains clamping force where an integrated washer is needed
• Helps keep electrical and mechanical connections stable
• Common symptom: loose or vibrating parts, squeaks, or components that shift during use

• One nut with attached washer

• Disconnect power and water before servicing
• Use the correct socket or wrench to avoid rounding the nut
• Tighten to snug fit — avoid overtightening which can strip threads or damage parts
• If replacing a rusted or damaged fastener, inspect mating threads and replace as needed

This condenser coil removes heat from the refrigerant so the refrigerator can cool effectively. Replacing a damaged or clogged condenser helps the appliance run more efficiently and maintain proper internal temperatures. What it does:

• Releases heat from the refrigerant after compression to allow the cooling cycle to continue
• Helps prevent the compressor from overheating and reduces excessive run time
• Commonly linked to symptoms like poor cooling, refrigerator running constantly, or unusual warmth in the cabinet
• May be visibly bent, corroded, blocked by debris, or leaking refrigerant if damaged

• One condenser coil

• Disconnect power and unplug the appliance before beginning any repair
• Condenser is usually mounted at the bottom or rear of the refrigerator; access may require removing kick plate or back panel
• Handle coils carefully to avoid bending fins or damaging tubing; worn protective gloves recommended

A replacement window locking bracket that secures the appliance window or inner door assembly for safe, stable operation. Restores proper window alignment and helps maintain a tight, secure fit to reduce rattling and movement. What it does:

• Secures the appliance window or inner door assembly to the frame
• Prevents the window from shifting or rattling during use
• Helps maintain a tight seal for consistent performance
• Commonly replaced when bracket is bent, broken, or missing

• One window locking bracket

• Installation requires basic hand tools; disconnect power before servicing if part is behind an energized assembly
• Handle sharp edges carefully and support the window/door while removing and installing the bracket
• If fasteners are damaged or missing, replace with equivalent OEM hardware