Parts for QHM12AXW1: Room Air Conditioner Parts

This UI board cover is the outer trim that protects and finishes the appliance control panel, keeping the user interface and electronics shielded from grease, steam and everyday wear while restoring a clean appearance. What it does:

• Covers and protects the control board and user interface from moisture, dirt and cooking residues
• Provides the finished trim and mounting surface for control buttons and display openings
• Helps prevent accidental contact with electronics behind the control panel
• Replaces cracked, warped or cosmetically damaged control-panel covers

• One UI board cover (single piece)

• Disconnect power to the appliance before starting any repair
• Remove any trim or control-panel screws and lift the old cover away; handle glass or plastic parts carefully to avoid scratches
• Verify orientation and alignment before tightening fasteners; do not force or over-tighten

The Control Board is an OEM component specifically designed for GE window air conditioners. Located internally within the indoor air handling unit, it provides centralized system management and sensor functions. 

The control board regulates critical components like the compressor, condenser fan motor, and temperature-sensing thermistor to enable automatic cool/heat modes. Integrated circuitry safely oversees all operational parameters for dependable temperature control.

Causes of a faulty control board relate to long-term environmental exposure and high-frequency switch operations degrading integrated circuits over many years of duty cycle. 

Symptoms include: 

• Non-responsive or unpredictable temperature settings  
• Error codes displayed or blinking control lights
• Total system failure to power on or operate properly

Replacing with this authentic GE OEM part restores optimized system regulation and trouble-free functionality. Compatible alternatives include select Frigidaire, Westinghouse, or Kenmore AC units.

This refrigerator air filter helps reduce odors inside the fresh food compartment for fresher-smelling food storage. It fits into the cabinet air filtration slot and refreshes circulating air for improved odor control. What it does

• Captures and helps reduce common refrigerator odors using a charcoal-based filter media
• Helps keep produce and other foods smelling fresher between cleanings
• Works with the refrigerator's internal air circulation to continuously filter cabinet air
• Common symptom: persistent or noticeable odors inside the fresh food compartment

• One replacement refrigerator air filter cartridge

• Replace filter according to the refrigerator manufacturer's instructions for location and orientation
• Turn off or pause dispensers/air circulation features if directed by the model instructions before replacing
• Dispose of used filter per local regulations; avoid damaging the filter housing when removing
• If odors persist after replacement, run the refrigerator a few hours to allow full air circulation

This replacement power cord supplies mains power to compatible GE appliances, restoring safe and reliable electrical connection. Use it when a frayed or damaged cord prevents the appliance from powering on or causes intermittent power. What it does:

• Replaces the appliance's factory power cord to restore electrical connection
• Stops power interruptions caused by damaged or worn wiring
• Reduces risk of shorts or sparks from cracked insulation (when installed correctly)
• Fits appliances designed for a three-prong, grounded cord connection

• One replacement power cord as shown

• Disconnect power at the house circuit or unplug the appliance before replacing the cord
• Secure strain relief and terminal connections per the appliance wiring harness and OEM instructions

This top rail is the backguard trim piece that covers and protects the rear edge of the cooktop and control console, restoring a clean appearance and helping keep debris out of internal openings. What it does

• Covers the gap between the cooktop and control console to improve appearance and keep crumbs and spills out of internal components
• Provides a finished mounting surface for control panel components and associated hardware
• Replaces bent, cracked, or corroded trim that can expose underlying parts
• Helps stop drafts or light gaps that may occur when the original rail is damaged

• One top rail/backguard trim piece

• Disconnect power (and gas if applicable) before starting any repair
• Removal typically requires lifting the cooktop or removing screws from the backguard; keep track of mounting hardware
• Handle edges carefully — trim pieces can have sharp metal edges

The Remote Control is an OEM part for GE window air conditioners. It allows convenient wireless operation from across the room.   

Causes of a faulty remote include faded or stuck buttons from heavy usage. Moisture or dust intrusion due to lack of sealing over time can compromise electronics. 

Symptoms of a bad remote control involve:

• Unresponsive or randomly operating buttons  
• Inability to power the unit on or off from a distance
• Range or reception issues where controls don't work
• Missing buttons preventing complete functionality

This GE replacement ensures hassle-free temperature adjustment without approaching the AC unit. Compatible with some Frigidaire, Danby, and Honeywell branded window air conditioners as well. The remote preserves full programming and convenient control when manual overrides are needed at the unit.

This installation parts kit provides the hardware needed to secure and align your appliance during installation, making fit-up easier and helping maintain safe, stable operation. Use it to replace missing or damaged mounting components. What it does:

• Supplies mounting hardware and fittings used to secure the appliance in cabinetry or to mounting surfaces
• Restores proper alignment and support when original installation hardware is missing or worn
• Helps reduce shifting, excessive vibration, or gaps caused by loose or damaged fasteners
• Supports safe, stable operation by ensuring the appliance is securely installed

• Always disconnect power (and gas, if applicable) before starting any installation work
• Use appropriate tools and mounting anchors for the installation surface; keep fasteners tight but avoid over-torquing