Parts for Lg LP1415GXR/00: Room A / C Parts

This remote controller assembly replaces the control board and button interface that receive remote signals and register front-panel button presses, restoring responsive control and user input for the appliance. What it does:

• Receives infrared remote signals and passes commands to the main control board
• Provides the front-panel buttons or touch inputs used for manual control
• Stops intermittent or no-response behavior when the IR or button circuit fails
• Helps resolve stuck, unresponsive, or non-registering front-panel buttons

• One remote controller assembly

• Disconnect power to the appliance before starting any work to avoid shock or damage
• Handle the board by the edges and avoid touching contacts to reduce ESD risk
• Reconnect ribbon/plug connectors fully and secure any mounting clips or screws
• Test operation with fresh remote batteries and normal power applied before final reassembly

This display PCB assembly controls the appliance's user interface and display functions, restoring visible controls and status indicators for proper operation. Replace a damaged or non-responsive display board to regain normal front-panel feedback. What it does:

• Hosts the display LEDs/LCD and related electronics so button presses produce visible responses
• Processes and shows cycle status, time, and error indicators on the front panel
• Routes signals between user controls and the main control board to ensure commands register
• Common symptom fixer: resolves blank, flickering, or unreadable display and unresponsive panel behavior

• Disconnect power before servicing to avoid shock or board damage
• Handle board by edges and avoid touching contacts or components to prevent ESD damage
• Verify connector orientation and secure all ribbon/plug connections before powering on

This AC indoor motor assembly powers the blower/fan in the indoor air-handling section, restoring airflow and circulation in compatible HVAC or split-system units. Built to replace the worn or failed indoor motor to help recover normal ventilation. What it does

• Drives the indoor blower or fan to move conditioned air through the evaporator and ductwork.
• Restores consistent airflow when a motor has stopped running, is noisy, or runs intermittently.
• Reduces vibration and unusual sounds when replacing a damaged or worn motor assembly.
• Works with the HVAC control system to respond to speed and start commands (where applicable).

• Disconnect power to the unit before attempting service to avoid shock or motor damage.
• Handle the motor assembly carefully; avoid bending terminals or damaging wiring harnesses.
• Some models require partial disassembly of the indoor air handler or cabinet.

This installation parts assembly is designed for over-the-range microwaves. It supplies the components needed to mount the unit securely to the wall and bottom of the cabinet, helping ensure proper support, alignment, and safe operation. What it does:

• Provides the hardware/components required to install and secure the microwave
• Helps align the unit for proper venting and cabinet clearance
• Restores safe mounting when original parts are missing or damaged
• Common symptoms: missing install hardware, loose/sagging unit, cannot complete installation

• One installation parts assembly

• Disconnect power before starting; two-person lift is strongly recommended
• Follow your model's installation guide/templates for hole locations and vent configuration
• Secure to wall studs or use approved anchors per instructions and local codes
• Level the unit and tighten fasteners evenly; do not overtighten

This thermistor assembly is the outside temperature sensor that provides accurate ambient readings to the appliance control so the system can regulate cooling and defrost cycles correctly. Replaces a failed or intermittent outdoor sensor to restore proper temperature monitoring. What it does

• Senses outdoor/ambient temperature and sends a temperature signal to the control board
• Helps the control determine cooling, heating or defrost timing
• A faulty sensor can cause incorrect temperature readouts, frequent cycling, or defrost problems
• Works as a direct-signal sensor; requires a functioning control board and wiring to operate

• One thermistor assembly (outside sensor), as shown

• Disconnect power before servicing to avoid shock or damage
• Verify connector orientation and secure wiring; do not force pins or bend contacts
• Handle the sensing element and wiring gently to avoid damage; avoid contaminating the sensor tip
• Test the thermistor with a multimeter per OEM resistance chart before and after installation to confirm operation

This installation parts assembly is designed for over-the-range microwaves. It supplies the components needed to mount the unit securely to the wall and bottom of the cabinet, helping ensure proper support, alignment, and safe operation. What it does:

• Provides the hardware/components required to install and secure the microwave
• Helps align the unit for proper venting and cabinet clearance
• Restores safe mounting when original parts are missing or damaged
• Common symptoms: missing install hardware, loose/sagging unit, cannot complete installation

• One installation parts assembly

• Disconnect power before starting; two-person lift is strongly recommended
• Follow your model's installation guide/templates for hole locations and vent configuration
• Secure to wall studs or use approved anchors per instructions and local codes
• Level the unit and tighten fasteners evenly; do not overtighten