Dryer Power Strike Small Engine Regular Starter Parts

This door-activated light switch controls the interior lamp in your refrigerator. Replace a worn or sticking switch to restore dependable lighting and prevent the bulb from staying on and warming the compartment when the door is closed.

• Opens and closes the light circuit as the door is opened and closed
• Helps prevent the light from staying on with the door shut
• Common symptoms: interior light won't turn on, stays on with the door closed, or works intermittently
• Physical signs may include a stuck/broken plunger or damaged housing

• Disconnect power before servicing
• Gently pry the old switch from the liner/panel and release its locking tabs
• Transfer wires one at a time to the same terminals on the new switch
• Press the new switch fully into place; restore power, and test

Replace a failed thermistor with this factory temperature sensor. It monitors temperature and feeds that data to the control, helping the appliance regulate heat and run cycles correctly. A faulty sensor can cause temperature-related performance issues.

• Senses temperature and sends a resistance signal to the control board for regulation
• Helps maintain proper heating/temperature during operation
• Failure may cause no heat or overheating, erratic or extended cycles, or temperature/sensor error codes
• Replace when sensor is open/shorted or readings are out of range per service diagnostics

• Disconnect power before servicing; if applicable, also shut off water or gas supply
• Access the sensor, unplug the wire connector, and remove any mounting screw/clip
• Install the new sensor; transfer any bracket/seal from the original and route wiring away from hot or moving parts
• Run a diagnostic or test cycle after replacement to confirm normal operation

This outlet thermistor monitors exhaust air temperature in the dryer's outlet duct and reports it to the control. Replacing a faulty sensor helps restore accurate heat regulation, preventing over- or under-drying for consistent drying performance. What it does:

• Measures outlet/exhaust air temperature and sends a resistance signal to the control board
• Helps the control cycle the heater or burner on/off to maintain proper drying temps
• Failure symptoms can include long dry times, no heat, overheating/shutting off, or inconsistent temperatures
• May illuminate a sensor-related error on models with diagnostics

• 1 outlet thermistor

• Disconnect power; shut off gas supply for gas models before servicing
• Access the exhaust/outlet duct or blower housing (location varies by model); the thermistor mounts on this duct
• Note wire locations, remove the fastener/clip, transfer any bracket if present, and install the new sensor with its tip in the airflow; secure connections
• Reassemble and run a test cycle to proper heat cycling

This dryer safety thermostat monitors internal temperature and opens the circuit if the unit overheats, protecting the heater and wiring. Replacing a failed thermostat restores proper over-temperature cutoff and safe, consistent drying performance. What it does:

• Monitors air temperature at the heater/exhaust path
• Interrupts power to the heating element if temperatures exceed its limit
• Helps prevent overheating and thermal damage
• Common symptoms can include: no heat, heat cutting out early or overheating, or the dryer shutting off on high heat

• 1 safety thermostat

• Disconnect power before service; for gas dryers, also shut off the gas supply
• Typically mounted on the heater housing or exhaust duct; note wire positions and transfer one at a time
• Secure with existing hardware and ensure tight electrical connections
• After replacement, clean the lint filter, vent hose, and exhaust duct to ensure proper airflow and prevent repeat overheat trips

This temperature-control thermistor (temperature sensor) feeds accurate temperature data to the control so your appliance can cycle components correctly and, where applicable, manage defrost. Replacing a faulty sensor restores stable operation and consistent performance. What it does:

• Senses temperature and varies resistance to report conditions to the control
• Helps the control regulate system cycling for proper operation
• Supports defrost logic where applicable to prevent coil icing
• Common failure signs: erratic temperature control, short/long cycling, icing on the evaporator, or unexpected shutoffs

• 1 thermistor

• Disconnect power before servicing
• Note the original sensor location and wire routing; install the new sensor in the same position
• Transfer any mounting clip or sleeve from the old sensor if needed
• Fully seat connectors and route wiring away from sharp, hot, or moving parts

This broken belt switch monitors drive belt tension and cuts power to the motor if the belt snaps or slips. Replacing a faulty switch restores proper start/run operation and maintains the dryer's built-in safety shutoff. What it does:

• Monitors belt tension through the idler mechanism
• Opens the motor circuit if the belt is broken or loses tension
• Helps prevent the motor from running when the drum isn't turning
• Failure symptoms include: dryer won't start, stops soon after pressing Start, or no motor sound while controls have power

• Includes 1 broken belt switch

• Disconnect power; turn off gas supply for gas models
• Access the switch near the belt/idler area; many models require removing the front panel and drum
• Note wire locations; move connectors to the new switch and secure in the original orientation
• Inspect belt and idler for wear; ensure correct belt routing/tension before reassembly

The Dryer Door Lever Assembly is essential for maintaining the functionality of your dryer. This genuine OEM part ensures a perfect fit and reliable performance, mirroring the quality of your original component. Designed specifically for Samsung dryers, the lever allows for smooth opening and closing of the dryer door, enhancing your overall user experience. Its durable construction provides long-lasting support, reducing the need for frequent replacements and saving you time and money. Installing the Dryer Door Lever Assembly is straightforward, helping you restore your dryer's convenience quickly and efficiently. By choosing this genuine OEM part, you ensure optimal performance and maintain the integrity of your appliance. Whether the original lever is worn out or broken, this Dryer Door Lever Assembly is the perfect solution to keep your dryer operating smoothly and effectively.

This thermal cut-off (TML) is a temperature safety device that opens the circuit if overheating is detected, protecting components from heat damage. Replace a failed or tripped cut-off to restore safe, reliable operation.

• Monitors temperature at its mounting point and interrupts power at a preset limit
• Helps prevent overheating damage to components and wiring
• Typical symptoms include no power, shutting off during use, or no heat—depending on where it's installed
• Can be tested with a multimeter; an open (no continuity) reading indicates replacement is needed

• Disconnect power before servicing; some appliances (e.g., microwaves) can store dangerous high voltage—use proper discharge procedures
• Replace with the same type/rating and mount in the same location/orientation as the original
• Ensure solid contact with the sensing surface and clear airflow/venting to prevent repeat overheating
• Do not bypass thermal safety devices; verify proper operation after installation

This Door Catch Bezel, in white, is an OEM part for Whirlpool dryers. It secures the dryer door, making sure it remains closed during operation. Crafted precisely to fit compatible dryer models, this bezel guarantees a secure and snug fit.

What causes a bad part:
The Door Catch Bezel might deteriorate due to frequent use, exposure to heat, or physical strain during the opening and closing of the dryer door. Additionally, prolonged exposure to cleaning agents or moisture can contribute to its degradation.

Symptoms for a bad part:

• Difficulty in securely closing the dryer door
• Loose or shaky door closure
• Visible damage or cracks on the bezel

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This lock cam is a small actuator that drives the appliance's door-lock mechanism. It translates the lock actuator's movement into a positive latch, helping the door lock securely when required and release correctly so cycles start and finish properly.

• Interfaces with the lock actuator and latch to engage and release the lock
• Wear, cracking, or rounding can cause the lock not to engage or to stick
• Common symptoms include a door/lid that won't lock or unlock, loose lock lever, clicking without latching, or door/lock-related error messages
• Restores proper linkage travel and switch actuation when the original cam is worn or damaged

• Disconnect power to the appliance before servicing
• Access the lock mechanism per your model; note the cam's orientation and any springs/linkages
• Install the new cam fully seated and ensure it engages the actuator and latch smoothly
• Reassemble, restore power, and test lock operation

This high-limit thermostat is a temperature safety switch for the heating circuit. It opens the circuit if temperatures climb too high, helping protect the appliance and restore safe, reliable heating performance.

• Monitors temperature and interrupts power to the heater when a limit is exceeded
• Helps prevent overheating that can damage components or trip other safeties
• If failed open: heater won't energize; cycles may run long or never reach target temperature
• If stuck closed: unit may overheat or shut down as other safety devices trip

• Disconnect power at the breaker before servicing; allow the appliance to cool completely
• Access the thermostat at the heater/temperature control area as designed for your model
• Note wire positions and transfer one at a time; ensure tight, secure connections
• After replacement, inspect the heater and controls for issues that could cause overheating

Sturdy metal door strike that mates with the latch/lock on your machine's cabinet. It keeps the door closed and engages the door switch so cycles can start and run without nuisance stops.

• Interfaces with the door latch/lock mechanism to secure closure
• Engages the door switch/interlock so the appliance can start and continue running
• Restores proper door alignment and latch feel after wear or bending
• Typical symptoms: door won't latch or pops open; unit won't start/run; intermittent stopping mid-cycle; visible damage to the strike

• Unplug the appliance (and shut off gas to gas dryers) before servicing
• Remove the existing strike and retain mounting hardware; note orientation
• Install the new strike in the same position; tighten screws and verify alignment
• Close the door to confirm smooth latching and proper operation

This in the male piece on the front panel. For the female piece on the door order WPW10111905.

The Door Strike is an OEM replacement part for Whirlpool dryers. This component ensures the dryer door securely latches, enabling the appliance to operate and preventing it from running with the door ajar. It works in conjunction with the door catch to maintain a proper seal during drying cycles.

Symptoms of a bad Door Strike include:

• The dryer door not latching or staying closed
• The dryer not starting due to the door remaining open
• The door popping open during operation
• Visible wear, bending, or damage to the strike

Causes of a failing Door Strike can include regular wear and tear, misalignment from improper use, or damage from slamming the door. Replacing a faulty strike ensures the dryer operates safely and efficiently.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This moisture sensor monitors dampness inside the dryer drum and signals the control when fabrics are dry, helping automatic cycles end on time and avoid overdrying. Replacing a failed sensor can restore consistent Auto Dry performance and cycle times. What it does:

• Detects moisture level via conductivity across the sensor surfaces inside the drum
• Sends feedback to the control so Auto Dry cycles advance and stop correctly
• Helps prevent overdrying and underdrying in sensor-based cycles
• Common symptoms of a faulty sensor may include: auto cycles ending too soon or running too long, clothes remaining damp, or the dryer staying on "Sensing" while timed cycles still work

• 1 moisture sensor

• Disconnect power and, if applicable, shut off gas before servicing
• Access the sensor at the front bulkhead/lint housing area; remove front panel as needed per model
• Transfer connectors and route wiring exactly as original; secure the sensor firmly
• Clean the sensor contact surfaces with rubbing alcohol; residue from dryer sheets or fabric softeners can affect readings

This NTC thermistor is the dryer's temperature sensor. It monitors exhaust air temperature and signals the control to cycle the heat, restoring accurate drying performance and helping prevent overheating, underheating, and inconsistent results.

• Monitors exhaust air temperature by changing resistance as heat rises (NTC behavior)
• Sends temperature feedback to the control to regulate the heater or gas valve
• Failure can cause no heat, overheating, or erratic temperatures
• May lead to long dry times, short cycles, or temperature-related error codes

• Disconnect power and, for gas models, shut off the gas supply before servicing
• Access the sensor on the blower housing or exhaust duct; location varies by model
• Note wire routing; unplug the harness connector; remove the mounting fastener/clip; install the new sensor fully seated and reconnect
• Reassemble, restore power, and run a test cycle; check and clean venting to ensure proper airflow