1068619712 Parts

This plain flat washer helps secure fasteners and evenly distribute load under nuts or bolts to prevent damage and loosening. A simple replacement when a washer is missing, rusted, or worn. What it does:

• Provides a smooth bearing surface between fastener and component to reduce wear
• Helps distribute clamping force to prevent stress on parts
• Reduces loosening from vibration when used with the correct fastener
• Common service part for assemblies where a thin metal spacer is needed

• Disconnect power and water to the appliance before beginning any repair
• Inspect the mating fastener and seating surface; replace any damaged hardware
• Slide the washer onto the bolt or stud with the flat faces against the mating surfaces; tighten fastener to secure but avoid overtightening

This temperature-sensing thermostat monitors and regulates appliance temperature to restore proper cycling and consistent performance. Replacing a failed thermostat helps resolve temperature drift and heating or cooling irregularities. What it does:

• Senses internal temperature and opens/closes the electrical circuit to control heating or cooling components.
• Restores correct on/off cycling so the appliance reaches and maintains the intended temperature.
• Common symptoms it can address: unit won't reach target temperature, runs too long or too short, or temperature fluctuates.
• Works as a safety and control device to prevent thermal extremes when functioning properly.

• Disconnect power to the appliance before beginning any repair to avoid shock or injury.
• Access may require removing exterior or interior panels; keep track of screws and fasteners.
• Match wiring terminals and orientation to the original thermostat; do not force connectors.

This door trim retainer replaces a broken or missing end cap that holds the door shelf rail/retainer bar in place on the refrigerator or freezer door. It keeps the rail secured so door-shelf contents are properly contained.

• Secures the door shelf trim/retainer bar to the door liner
• Helps keep the rail aligned and prevents it from loosening or falling off
• Replace when the end cap is cracked, missing, or won't hold the rail
• Common symptoms: loose or sagging door rail, bar popping off, gaps at the rail ends

• Disconnect power before servicing
• Support the rail, then release and remove the damaged end cap
• Reuse existing screws/fasteners if your model uses them
• Align and snap/secure the new end cap; ensure the rail is fully seated

Ice cube/utility container.

This replacement ice cube tray is a direct-fit plastic tray designed to hold and release ice cubes in compatible top- or bottom-freezer refrigerators. Restores convenient ice storage and simple manual ice removal. What it does:

• Holds water in separate cavities so ice cubes form evenly.
• Flexes slightly for easier ice release to reduce twisting or chipping.
• Replaces cracked, warped, or missing trays that cause leaking or uneven freezing.
• Helps prevent contamination from freezer debris when used as intended.

• Remove old tray and wipe area clean before installing the new tray.
• Fill tray with water on a level surface and place flat in the freezer to freeze.
• Handle carefully when removing ice to avoid spills; do not force with sharp tools.
• Clean tray before first use and as needed; follow refrigerator manufacturer's care guidance.

This door trim retainer end cap secures the decorative trim on a refrigerator or freezer door, restoring a finished look and keeping the trim aligned. It helps prevent gaps, rattling trim, and moisture intrusion around the door edge. What it does

• Clips into the door trim to hold the trim firmly in place.
• Keeps door trim aligned to reduce cosmetic gaps and noise.
• Helps maintain a proper seal by preventing trim from pulling away.
• Common symptom: visible gap or loose/rattling trim pieces.

• One door trim retainer end cap.

• Designed for a snap-in replacement; may require a flat tool to pry off the old retainer gently.
• Inspect trim and surrounding clips for damage; replace any broken clips before installing.
• Disconnect power only if working near electrical components; this trim replacement is cosmetic/mechanical.

This is a genuine replacement screw used to secure panels, brackets, and components on compatible Whirlpool appliances. It restores proper fastening so loose parts stop rattling and panels stay aligned. What it does

• Fastens trim, panels, brackets, or mounting hardware to appliance chassis
• Helps stop vibration and rattling caused by missing or stripped fasteners
• Restores secure connections after repair or part replacement
• Matches OEM thread specification to fit intended mounting holes

• Disconnect power to the appliance before beginning any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Start threads by hand and tighten until snug; do not overtighten
• Inspect mating threads and replace if damaged

Relay and overload kit for a compressor.

This ice tray is the molded bin that holds and releases ice cubes in your refrigerator freezer, offering a simple replacement for cracked, warped, or leaking trays so you can make and store ice reliably. What it does:

• Holds water in individual pockets that freeze into ice cubes
• Releases cubes when twisted, flexed, or used with the ejector mechanism
• Restores proper water containment if the original tray is cracked or warped
• Helps prevent water leakage into the freezer compartment

What's included:

• One replacement ice tray

Install notes:

• Remove any remaining ice and empty water before removing the old tray
• Typically installs by sliding or snapping into the freezer shelf or bracket—align trays before seating
• Handle carefully to avoid breaking brittle plastic; wear gloves if needed
• No tools usually required; follow refrigerator manual for any model-specific steps