1102887290 Parts

Color: Almond

This trim piece finishes and protects an opening or edge on your appliance's cabinet or console. Replacing a cracked or missing trim restores a clean, factory look and helps nearby components sit and operate as intended. What it does:

• Provides a clean, finished edge and covers sharp cabinet/console edges
• Helps keep adjacent parts aligned and secured around the opening
• Restores appearance when original trim is cracked, warped, discolored, or missing
• Common symptoms: loose or rattling piece, cosmetic damage, snagging edges, or poor fit of nearby parts

• 1 trim piece

• Disconnect power; if applicable, shut off gas or water. Wear cut-resistant gloves.
• Remove the existing trim by releasing clips or removing screws; note orientation and retain hardware.
• Transfer any reusable clips/inserts from the old trim to the new part.
• Align and snap/screw the new trim into place; do not overtighten.

Size: .20 Fl. Oz. (6 ml)

A small rubber bumper that cushions and protects appliance doors, drawers or panels to reduce noise and prevent hard contact. Replaces worn or missing bumpers to restore a snug, quiet close. What it does:

• Provides a soft buffer to stop doors or drawers from banging into the cabinet or frame
• Reduces vibration and rattling during operation
• Helps doors and panels sit properly when closed
• Simple, non-electrical part — no wiring or adjustment required

• One replacement bumper

• Inspect the mounting hole or surface; clean debris before installing
• Press the bumper into the hole or onto the surface until fully seated; use a blunt tool if needed for tight fits
• Disconnect power to the appliance first and follow OEM instructions
• Remove old adhesive before installing the new bumper

Includes suspension pads.

Left hand side.

This clutch spring cap retains and protects the clutch spring in your washer's drive/clutch assembly, maintaining proper tension. Replacing a worn or missing cap helps the clutch engage smoothly and reduces slipping and noise during spin.

• Secures the clutch spring within the clutch assembly to prevent movement or dislodging
• Maintains correct spring preload for consistent clutch engagement
• Can help reduce clutch slip that appears as weak/no spin, slow spin ramp-up, or intermittent spinning
• Common signs of trouble: rattling or scraping near the drive, burning smell, or a visibly damaged/missing cap

• Unplug the appliance and shut off water before servicing
• Access the clutch per your model's service procedure; removing the gearcase/transmission and clutch may be required
• Carefully relieve spring tension and note the orientation of the spring and cap before removal
• Inspect the spring, clutch lining, and related hardware; replace any worn components during reassembly

Straight knurled pin that secures knobs or small components to a shaft for a tight, slip-resistant fit. Replaces a worn or missing pin to stop loose, wobbly, or spinning knobs and restore reliable engagement. What it does:

• Secures knobs, dials or small parts to control shafts by providing a press-fit, knurled surface.
• Prevents wobble, slipping, or spinning of control knobs that won't turn with the shaft.
• Common service symptom: knob spins freely or fails to engage controls.
• Used where a small metal pin is required to lock a component onto a splined or smooth shaft.

• Disconnect power and unplug the appliance before servicing.
• Remove the knob or access panel to reach the shaft; pin is typically press-fit.
• Removal/installation may require needle-nose pliers, a small punch, or a bench press; protect surrounding parts from damage.
• Keep small parts away from children and follow appliance safety guidelines; replace mating hardware if the shaft or hole is damaged.

Replacement end cap that restores the appliance's finished edge and helps protect internal components from debris. A simple, low-cost repair to replace cracked, broken, or missing end caps and reduce trim wear. What it does:

• Covers and protects an exposed edge or end of the cabinet/trim.
• Helps prevent snagging, dirt buildup, and contact damage where the cap is missing or cracked.
• Restores the appearance and alignment of surrounding trim pieces.
• Common symptom: visible crack, loose or missing trim, rubbing or catching at the edge.

• Disconnect power and/or water supply to the appliance before beginning work when applicable.
• Inspect the mating surface and remove old adhesive or fasteners before installing the replacement cap.
• Install by aligning the cap and snapping or fastening into place; do not force—use correct fasteners if applicable.
• If surrounding trim is damaged, consider replacing affected pieces to ensure proper fit and finish.

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

Size: 10-24 x 3/8 inch.

This drain hose clamp secures the hose connection to keep water where it belongs during the drain cycle. A tight, reliable clamp helps prevent leaks and hose pull-off from vibration or pressure changes. What it does:

• Secures the drain hose to a pump outlet or drain port to maintain a watertight seal
• Helps prevent the hose from slipping off during operation
• Reduces leaks at the hose connection point
• Common symptoms of a bad clamp: water leaking at the drain hose joint, a loose/detached hose, or a visibly rusted/broken clamp

• 1 clamp

• Disconnect power and turn off the water supply; place a towel to catch residual water
• Access the hose connection, remove the old clamp, and inspect the hose end and fitting; replace the hose if cracked or swollen
• Position the new clamp correctly over the hose and behind the fitting bead; tighten/seat evenly without overtightening
• Reassemble and run a brief drain test to check for leaks

This screw-washer assembly secures panels, brackets, and other appliance components. The integrated washer spreads load and resists loosening, so replacing a worn or missing fastener restores a tight, reliable fit and helps eliminate rattles.

• Provides fastening with a built-in washer for even clamping and retention
• Replaces missing, stripped, or corroded hardware
• Helps address loose panels/handles and vibration or rattle noises
• Supports proper alignment of covers, brackets, and trim

• Disconnect power and shut off water or gas (as applicable) before servicing
• Match to the original fastener; location and quantity in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten with the correct driver
• Do not overtighten; replace other severely rusted or damaged fasteners in the same area

This drain hose coupling connects two sections of the washer drain hose to restore a watertight path for wastewater, helping prevent leaks and restore proper draining. What it does:

• Joins two drain hose sections or connects hose to a mating outlet for secure water flow
• Seals the hose connection to reduce leaks at the joint
• Restores proper draining when a damaged or missing coupling causes slow drain or leakage
• Designed to fit the OEM hose profile for a snug, stable connection

• One drain hose coupling as shown

• Turn off power and water supply before starting any repair
• Inspect hose ends for damage; trim to clean cut if required for proper fit
• Push hose ends fully onto the coupling and secure with manufacturer-recommended clamps

This spring damper assembly cushions and stabilizes the appliance drum during spin cycles, reducing vibration and helping maintain smooth, balanced operation. It restores proper drum support and motion control for safer, quieter performance. What it does:

• Absorbs and dampens drum movement to reduce vibration and banging during spin
• Helps keep the drum properly aligned to prevent wobbling or rubbing
• Can resolve symptoms such as loud thumping, excessive vibration, or uneven spinning
• Works as the suspension support between the drum and cabinet to improve cycle stability

• Disconnect power (and water, if applicable) before beginning any repair
• Handle springs and mounting points carefully—springs are under tension and can snap if released improperly
• Installation may require partial disassembly of the cabinet or drum; follow the OEM service manual or instructions

This syphon breaker prevents dirty drain water from being siphoned back into the dishwasher, helping maintain proper draining and protect wash water from contamination. It's a direct-replacement drain air-break for compatible dishwashers. What it does:

• Stops backflow/siphoning from the household drain into the dishwasher
• Helps maintain proper drain performance and prevents wastewater re-entry
• Can reduce odors and cloudy or soiled dishes caused by contaminated wash water
• Works as part of the dishwasher's drain plumbing to preserve wash hygiene

• Disconnect power to the appliance and turn off water supply before servicing
• Replace only with identical part and ensure correct hose routing and secure clamps
• Inspect adjacent drain hoses and connections; replace damaged hoses or clamps as needed