205C-2981-Pod-112 Parts

This 3-speed blower switch controls the exhaust fan in your range hood, allowing you to select low, medium, or high airflow. Replacing a worn switch can restore dependable ventilation and proper speed control. What it does:

• Selects low, medium, or high fan speed by routing power to the blower motor
• Helps resolve a fan that will not run, runs only on one speed, or will not change speeds
• Can address a switch that feels loose, sticks, or works intermittently

• 1 three-speed blower switch

• Disconnect power at the breaker before servicing
• Access the control area; note wire locations (or take a photo) and transfer wires to the new switch one at a time
• Ensure push-on terminals are fully seated and secure
• Test all fan speeds before reassembly

Replacement bridge heating element kit that restores consistent heat across two adjacent cooktop terminals for large cookware and griddles. Replaces a damaged or worn bridge element so your cooktop can heat evenly and reliably. What it does:

• Bridges two adjacent surface element terminals to provide an expanded cooking zone for griddles and large pans.
• Heats the cooking surface where a single element can't cover wide cookware.
• Common symptoms it can fix: one side of a bridged zone not heating, intermittent heat, or visible element damage.
• Works as the direct replacement component to restore normal cooktop heating functionality.

• One bridge heating element replacement kit.

• Disconnect power (unplug or switch off breaker) before inspecting or replacing the element.
• Handle element carefully to avoid bending; use basic hand tools and note terminal connections for reassembly.
• Reconnect wiring securely and verify proper operation after restoring power.

Used for the pressure switch.

Right hand side. For screws use WPW10119828.

This condenser fan shroud sits in the rear machine compartment and positions the fan and motor to move air through the condenser coil. A cracked or warped shroud can reduce cooling performance and increase noise or vibration.

• Directs and focuses airflow across the condenser coil and compressor to remove heat
• Holds the condenser fan motor and blade in proper alignment
• Helps maintain stable refrigerator/freezer temperatures and efficient operation
• When damaged, may cause weak airflow, warmer temps, vibration, or fan scraping/rubbing noises at the back of the unit

• Unplug the refrigerator and wear cut-resistant gloves
• Pull the unit forward and remove the lower rear access panel to reach the machine compartment
• Take a photo of fan/motor orientation; transfer components to the new shroud and reuse existing hardware
• Confirm blade spins freely with proper clearance before restoring power

The Drawer Glide Gear is an OEM replacement part for Frigidaire refrigerators. It is a metal component located on each side of wire shelf tracks that work together to make shelf and drawer movements smooth. 

Causes of bad glide gears can include wear from years of extended usage, dents or deformation that restrict proper motion, or failure of lubricating parts inside the gear mechanism.

Symptoms of a bad Drawer Glide Gear include:

• Shelves or drawers that stick or fail to slide freely
• Noisy squeaking or grinding noises coming from shelf areas  
• Shelves difficult to properly align or position as needed

As a high-stress moving part, glide gears can degrade and lead to slothful storage access over time. Replace with this genuine OEM component for optimally smooth shelf performance on your Frigidaire refrigerator. The replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Replacement fastener used to secure appliance components. If a screw is missing or damaged, panels and brackets can loosen or rattle. Installing a new screw restores a tight fit and helps keep parts properly aligned.

• Fastens panels, brackets, or internal components as designed for the model
• Replaces missing, stripped, or corroded hardware
• Helps reduce vibration/rattling and restores proper fit
• Maintains alignment and a secure assembly after service

• Disconnect power; shut off gas if applicable before servicing
• Support components while removing/installing fasteners
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace all required screws in a location for even clamping and proper fit

Size: 8 x 1-1/4 inch.

The timer dial fits over the timer shaft on the control panel. It displays cycle options and provides a secure, aligned surface for the knob to rotate the timer so selections line up correctly.

• Surrounds the timer knob and shows cycle names/markers
• Aligns with the timer so the knob can index and turn settings properly
• Typical symptoms: cracked or broken ring, faded markings, loose/wobbly dial, difficulty selecting or aligning cycles
• Direct-fit replacement of the original timer dial

• Disconnect power to the appliance
• Pull off the timer knob; remove any retaining clip or nut if present
• Lift off the old dial; align the new dial with the panel indexing and timer shaft, then press into place
• Reinstall the retainer and knob; restore power and verify alignment

This replacement bar is a direct-fit support component that helps hold and stabilize a refrigerator door or interior shelf assembly, restoring secure storage and preventing items from shifting or falling. What it does

• Provides structural support for a door or shelf ledge to keep stored items secure
• Replaces bent, cracked or broken bars that allow shelves or door bins to sag
• Helps stop rattling or movement from loose or damaged supports
• Restores proper alignment so shelves and bins sit flush and stable

• One replacement bar

• Disconnect power before removing refrigerator doors or interior components when necessary
• Remove affected shelf or bin to access mounting points
• Use basic hand tools; avoid overtightening fasteners to prevent cracking plastic parts
• Handle glass shelves and door bins carefully during removal and reassembly

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required

This replacement retainer clip secures trim, panels or small components inside your appliance to restore proper fit and reduce rattling. A simple, low-cost part commonly used where plastic or metal pieces need a secure hold. What it does:

• Holds panels, trim pieces or small assemblies in place to prevent shifting and vibration.
• Helps stop rattling, loose trim or components that don't stay seated.
• Keeps wiring or hoses routed and restrained when used as a harness/route clip.
• Suitable when original clip is cracked, broken or missing.

• Disconnect power to the appliance before beginning any work.
• Remove surrounding trim or panels gently to access the clip location; a trim tool or small screwdriver may be helpful.
• Clip installs by pressing into the mating slot or hole until it snaps; pliers may assist for removal/replacement.
• Verify correct orientation and fit by comparing the new clip to the old one before final reassembly.

This fill hose carries water from the home supply to the appliance inlet valve, restoring proper water fill and helping prevent leaks when the original hose is cracked, worn, or blocked. Ideal for replacing damaged inlet lines. What it does:

• Delivers water from the household supply to the appliance inlet valve for normal fill cycles.
• Replaces cracked, split, or deteriorated hoses that can cause leaks at connections.
• Resolves symptoms such as slow or no water fill, visible leaks, or intermittent filling.
• Durable replacement designed to match OEM routing and connection points.

• Always shut off water supply and disconnect power before starting work.
• Inspect and replace hose clamps or inlet gaskets as needed; ensure proper seating to prevent leaks.
• Hand-tighten fittings and secure clamps—avoid overtightening metal fittings.
• After installation, restore water and power and run a short fill cycle while checking for leaks.

Size: .20 Fl. Oz. (6 ml)

This replacement screw fastens appliance components such as panels, brackets, and covers. Installing a new fastener restores a snug, rattle-free fit when the original screw is missing, stripped, or corroded.

• Secures covers, brackets, or trim to the cabinet or liner
• Replaces missing, stripped, or rusted hardware
• Helps reduce vibration and rattling from loose parts
• Supports proper alignment and stability of assemblies

• Disconnect power before servicing the appliance
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Do not overtighten, especially into plastic or thin sheet metal
• Retain and reinstall any original washers or spacers, if present

Replace the worn bearing that supports your refrigerator's ice-dispenser auger. This bearing helps the auger spin smoothly so cubes travel to the chute, restoring steady ice dispensing and reducing grinding or jamming.

• Supports the auger shaft within the ice bin/dispenser assembly
• Enables smooth rotation to move ice toward the chute
• Wear can cause slow or failed dispensing and squealing/grinding noises
• Fixes issues with a cracked, worn, or seized auger support

• Disconnect power and remove the ice bin before servicing
• Separate the bin front/cover and auger assembly; note the bearing's orientation
• Transfer the new bearing and reuse existing screws/retainer if present
• After reassembly, confirm the auger turns freely by hand before restoring power