253703133210 Parts

This is a replacement screw used to secure appliance panels and components. It restores proper fastening to stop rattles and keep parts aligned for reliable operation. What it does:

• Secures trim, brackets, or small panels to the appliance
• Prevents loose parts that can cause vibration, noise, or improper sealing
• Restores factory fastening where a screw is missing or damaged
• Simple, single-purpose fastener — use where the original screw was installed

• Use the matching screwdriver or bit to avoid stripping the head
• Do not overtighten; snug until secure to prevent thread or component damage
• Disconnect power or follow appliance safety steps when working near electrical components
• Replace only the screw(s) that match the original size and type

This mounting bracket secures internal components to the appliance frame, helping keep assemblies aligned and stable for reliable operation. It's a simple replacement that restores proper support where the original bracket was worn or damaged. What it does:

• Provides structural support for panels or internal assemblies to prevent shifting or rattling
• Keeps connected parts aligned to maintain proper function and reduce noise
• Commonly replaced when the bracket is bent, broken, or missing hardware
• Helps prevent further wear on adjacent components by restoring correct positioning

• Follow the appliance service manual for correct placement and fastener torque
• Disconnect power (and water if applicable) before starting any repair
• Use appropriate hand tools and retain all original fasteners unless they are damaged

This light shield is the clear interior lens that covers and protects the refrigerator light, helping diffuse lamp output for even illumination and keeping the bulb shielded from spills and bumps. What it does:

• Covers and protects the interior lamp from food, moisture, and impact
• Diffuses light for more even brightness inside the compartment
• Helps prevent direct contact with the hot bulb for safer operation
• Commonly replaced when cracked, cloudy, or missing

• Disconnect power to the appliance before starting work
• Remove any shelving or clips blocking access to the lens before lifting out the old shield
• Handle the replacement lens carefully to avoid cracking; secure with original clips/screws per factory fit
• If you see damage to mounting clips or wiring while installing, stop and verify those parts before restoring power

This wiring harness connects the appliance's control board or power source to internal components, restoring electrical continuity for reliable operation. Replace a damaged harness to stop intermittent power or non-responsive functions. What it does

• Routes power and signals between the control and components so controls, switches and motors operate correctly.
• Common symptom: controls or display are unresponsive or intermittent.
• Common symptom: specific functions (motors, lights, heating elements) do not receive power.
• Helps prevent shorts and arcing when routing and insulation are intact.

• One wiring harness as pictured and specified by the manufacturer.

• Disconnect power (unplug or shut off breaker) before accessing internal wiring.
• Verify connector orientation and seating; match wire colors and terminal positions during reassembly.
• Replace only the harnesses explicitly listed for your exact model to avoid mis-wiring.
• If you see burned terminals or damaged connectors, inspect adjacent components and replace as needed.

This dispenser heater kit warms the dispenser area to help prevent ice build-up and keep the water/ice dispenser operating reliably. Replaces a failed heater assembly to restore proper dispenser function. What it does:

• Heats the dispenser chute/valve area to reduce frost and ice clogging
• Helps restore reliable water or ice dispensing when the dispenser intermittently freezes
• Prevents repeated thaw cycles that can cause leaks or inconsistent dispense flow
• Works as the direct replacement heater component used in the dispenser assembly

• Disconnect power to the appliance before beginning any work
• Access may require removing the dispenser housing or control panel
• Handle electrical connections carefully and secure wiring per OEM routing

The Fresh Food Door Gasket is an OEM replacement part for Frigidaire refrigerators. It creates a seal around the refrigerator door to maintain a consistent temperature by keeping cold air in and warm air out. This helps ensure proper refrigerator conditions and prevents energy loss.

Over time, gaskets can degrade due to wear, exposure to extreme temperatures, or cleaning with harsh chemicals. A damaged or worn gasket may fail to seal properly, affecting the freezer's efficiency and potentially leading to increased energy consumption.

Symptoms of a bad gasket include:

• Frost or ice buildup inside the refrigerator
• Difficulty keeping the refrigerator door fully closed
• Warm air entering the refrigerator, causing temperature fluctuations
• Increased energy bills due to inefficient operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

NOTE: GASKET NOW GRAY, NOT WHITE

This water filter base secures the refrigerator's replaceable water filter cartridge and directs filtered water to the dispenser and icemaker. Replacing a damaged base restores a proper seal and helps prevent leaks and flow interruptions. What it does:

• Holds and seals the water filter cartridge so water passes through the filter media
• Directs filtered water to the dispenser and icemaker plumbing
• Prevents leaks caused by cracked or worn filter housing
• Can resolve low water flow, intermittent dispensing, or water taste issues when base is leaking or not sealing

• One water filter base assembly

• Turn off refrigerator and shut off the water supply before starting
• Relieve system pressure by dispensing water until flow stops, if applicable
• Remove the old housing carefully; inspect O-rings and replace if damaged
• Hand-tighten only; check connections and test for leaks after restoring water and power

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head

This refrigerator water filter mount secures the filter head/housing to the liner so the cartridge seats squarely and seals. Replace a cracked or loose mount to restore a snug fit and help prevent leaks or vibration.

• Holds the water filter housing firmly in place
• Aligns the cartridge for proper engagement with the filter head
• Helps maintain a watertight seal at the filter connection
• Common symptoms: filter won't lock in or sits crooked, drips around the filter area, difficulty installing/removing the filter, or rattling from a loose housing

• Disconnect power and shut off the water supply; dispense water to relieve line pressure
• Remove the filter and any cover/trim to access the mount; retain existing screws for reuse
• Install the new mount and tighten screws gently to avoid cracking plastic
• Reinstall the filter, restore water and power, flush the dispenser, and check for leaks

This refrigerator door mullion is the flip-up divider attached to the fresh food door that covers the gap between doors. It helps the doors seal properly, limiting air leaks and moisture at the center seam for consistent cooling performance. What it does and common symptoms:

• Flips into place as the door closes to create the center seal between doors
• Helps maintain interior temperature and reduce condensation at the door seam
• Replace if cracked, warped, loose, or not springing/aligning with the door gasket
• Symptoms can include doors not latching cleanly, visible damage, or moisture along the middle

• One door mullion assembly

• Unplug the refrigerator before servicing
• Remove door bins if needed; support the mullion and remove the mounting screws
• Lift the mullion off its pivots, position the new part, and reuse existing hardware to secure it
• Verify smooth flip action and a tight seal before restoring power