253704134415 Parts

This replacement screw secures refrigerator components such as brackets, trims, and covers. Replace missing or stripped hardware to keep parts tight and aligned, helping eliminate rattles and restoring a solid, reliable fit.

• Fastens interior or exterior components to the cabinet or doors
• Replaces missing, rusty, or stripped hardware
• Helps reduce vibration noises from loose parts
• Restores proper fit and alignment of panels, trims, or covers

• Disconnect power; turn off water supply if working near the dispenser or ice system
• Retain and reuse any original spacers or washers
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace one fastener at a time to maintain alignment

This replacement part is a set screw, and it is intended for use in different types of appliances. This is a genuine replacement part made by Frigidaire. This screw set is compatible in many different areas of the appliance. Screws are typically used for keeping parts of the machinery secure and in place. It is possible that screws can become loose over time and need to be replaced. A new screw set might be needed if the user notices parts of the appliances are becoming loose or are falling off. This can be due to screws becoming stripped over time or if the appliance is bumped during transport. It is typically easy to replace screws. Simply remove the old screw and replace it with a new part. The only tools needed for this repair are a screwdriver and possibly pliers if the damaged screw is stuck in place.Note that this is a genuine OEM replacement part and is sourced from the manufacturer. This set screw is sold individually.

This thermistor is a temperature-sensing resistor that monitors internal temperature and reports it to the control. Replacing a faulty sensor restores accurate temperature feedback for proper operation and consistent, reliable cycle performance. What it does:

• Continuously measures temperature and changes resistance for the control to read
• Helps regulate heating/cooling and overall cycle timing
• Supports safety logic that prevents improper temperatures
• Failure may cause inaccurate temperatures, long/short cycles, or temperature-related error codes

• 1 thermistor

• Disconnect power before servicing; shut off water or gas if applicable
• Access the sensor, note wire routing/orientation, and transfer any existing clip or seal as needed
• Make secure electrical connections and route wires away from hot or moving parts
• Many appliances use multiple sensors—diagnose with an ohm/diagnostic test before replacement, then run a test cycle after install

This refrigerator water inlet tube routes water from the supply/valve into the appliance's water system. Replacing a cracked or kinked tube restores proper flow to the dispenser and ice maker while helping prevent leaks.

• Directs water from the inlet valve to internal components for dispensing and ice production
• Maintains a sealed, food-grade water path
• Replace if you notice leaks under/behind the unit, visible cracks/kinks, reduced or intermittent dispenser flow, or ice maker not filling
• Normal wear, brittleness, or damage during moves can lead to failures

• Disconnect power and shut off the water supply before servicing
• Place a towel or tray to catch residual water when disconnecting lines
• Note the original routing; release any retaining clips and disconnect the tube from fittings
• Route the new tube exactly like the original and fully seat tube ends in connectors; restore water and check for leaks

This mullion assembly forms the front center divider of the refrigerator and includes an integrated anti-sweat heater. It helps keep the area where the door gaskets meet dry, supporting a clean look and a reliable, moisture-free seal.

• Provides the rigid center divider that the door gaskets seal against
• Built-in heater warms the divider to reduce sweating/condensation in humid conditions
• Helps limit air leaks that can lead to moisture, frost, or temperature fluctuations
• Common signs of trouble: persistent condensation on the center divider, visible cracks/warping, or poor gasket contact along the center

• Disconnect power to the refrigerator before servicing; wear cut-resistant gloves
• Remove mounting fasteners, carefully release the assembly, and disconnect the wire harness (note routing/orientation)
• Position the new assembly, reconnect the harness securely, and reinstall fasteners without overtightening
• Verify doors close smoothly and gaskets contact evenly along the divider before restoring power

This replacement block is a small structural component used inside the refrigerator to locate, support, or align its mating parts. Replacing a worn or broken block restores proper fit and helps keep the affected assembly secure. What it does:

• Provides a stable mounting/locating point for the applicable assembly
• Helps maintain alignment and reduces wobble or looseness
• Common failure signs: cracks, missing piece, or stripped fastener hole
• Symptoms may include rattling, sagging, or parts that won't stay in place

• 1 block

• Unplug the refrigerator before servicing; wear cut-resistant gloves
• Remove items and any obstructing parts to access the block; note orientation for reassembly
• Transfer any reusable hardware from the old block and secure the new block without overtightening
• Restore power and verify proper fit and operation of the serviced area

This #10-32 x 3/4-inch machine screw secures appliance components such as panels, brackets, and handles. Using the correct length and thread helps restore a snug, rattle-free hold wherever this screw is specified by the manufacturer.

• Fastens components with a #10-32 machine thread and 3/4-inch length
• Helps keep panels, trim, brackets, or handles secured and aligned
• Replaces missing, stripped, or corroded hardware
• Common signs include loose or wobbly parts, rattling, missing screws, or damaged screw heads/threads

• Disconnect power before servicing; if working near a water connection, shut off the water supply
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten to prevent stripping plastic or threads
• Reuse any model-specific washers or spacers if present

This turntable roller assembly sits under the glass tray to support and guide it as it rotates. Replacing a worn or damaged ring helps restore smooth tray movement for more even heating and dependable microwave performance.

• Supports the glass tray and allows smooth, consistent rotation
• Helps prevent tray wobble, binding, or scraping noises
• Can address issues like the tray not turning or uneven cooking
• Replaces cracked, warped, or missing roller rings

• Disconnect power before servicing
• Remove the glass tray, lift out the old ring, and clean the cavity floor
• Place the new ring wheels-down, seat the tray on the coupler, and test rotation
• Do not operate the microwave without the roller ring and tray properly installed

The Mullion is an OEM part for Frigidaire refrigerators. It is situated between the freezer and refrigerator doors to separate the two compartments. The mullion provides structure, sealing the doors against air and temperature leakage.

Causes of a bad mullion can include wear and tear over time, damage from frequent door opening and closing, or impact damage.

Symptoms of a bad mullion include:

• Air and temperature leakage between compartments
• Difficulty closing one or both doors securely
• Gaps or cracks seen around the mullion frame
• Scratches, dents or other physical damage

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This water connector links sections of the refrigerator's water supply tubing, maintaining a sealed path to the dispenser and ice maker. Replace a cracked or leaking connector to stop drips and restore reliable water flow and ice production.

• Connects sections of internal water tubing between components (inlet valve, filter, door, ice maker)
• Helps maintain a sealed route for proper dispenser and ice maker operation
• Common symptoms: water leaking behind/under the refrigerator, weak/no dispenser flow, ice maker not filling, visible damage at the fitting
• Direct-fit component built to OEM specifications for the intended application

• Unplug the refrigerator and shut off the household water supply before servicing
• Dispense water to relieve line pressure; place a towel to catch residual water
• Cut tubing ends square and fully insert into the connector until seated; tug gently to confirm engagement
• Restore water, check carefully for leaks, and recheck after the first dispense cycle

Specs: Hex head ,1/4-20 x 5/8

This replacement screw secures appliance components in place. Use it to replace a missing, stripped, or rusted fastener so shelves, handles, panels, or brackets stay properly mounted and the unit operates without unwanted movement.

• Fastens components to the cabinet, door, liner, or frame
• Restores a solid fit when the original screw is worn or lost
• Helps eliminate looseness, rattling, or misalignment
• Matches the original hardware for correct fit and thread engagement

• Disconnect power before servicing; for refrigerators, also turn off the water supply
• Align parts and start the screw by hand to avoid cross-threading
• Tighten with the correct driver; do not overtighten, especially into plastic
• If receiving threads are damaged, repair or replace the mating clip/bracket before installing

This hinge bracket supports and aligns the refrigerator door at the pivot point, helping the door open and close smoothly and seal properly. Replacing a worn bracket can restore stable door movement and reduce air leaks.

• Provides rigid support for the door hinge to maintain proper alignment
• Helps ensure a consistent door seal to prevent temperature fluctuations
• Common fix for loose, sagging, or misaligned doors
• Helps if the door makes popping/grinding noises when opening or closing

• Unplug the refrigerator and wear cut-resistant gloves
• Support the door before removing hinge fasteners to prevent drops
• Transfer and reinstall existing screws/hinge pin as needed
• Check door alignment and gasket contact after installation

This electronic main control board manages key refrigerator operations, coordinating cooling, defrost, and other functions so the appliance runs correctly.

• Regulates compressor and fans to maintain set temperatures
• Controls automatic defrost cycle
• Can resolve issues like no cool, warm freezer/fresh food, or intermittent operation
• May restore unresponsive controls or error/fault behavior

• Disconnect power before servicing; sensitive electronics—use ESD protection
• Photograph/label wire connections to ensure correct reassembly
• Handle by edges; avoid touching components and solder points
• After installation, restore power and allow normal cool-down period

The Door Handle is an OEM part for Frigidaire refrigerators. It is the surface component grasped and pulled open to access items stored in the bottom freezer.

Causes of a faulty handle can include cracks or breaks in the plastic material, worn friction pads diminishing grip, or damaged attachment components.

Symptoms of a bad freezer door handle include:

• Difficulty opening the freezer door
• Handle easily detaching when pulled
• Inability to keep freezer door securely closed

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This door handle bar lets you grip and open the appliance door smoothly. It restores a secure, comfortable handle when the original bar is loose, worn, or damaged, helping the door operate as intended.

• Provides a sturdy handhold to open and close the door
• Replaces a loose, cracked, or missing handle bar
• Helps ensure proper door operation and user safety
• Cosmetic refresh for a worn or scuffed handle area

• Unplug the appliance before servicing
• Use the correct screwdriver/hex driver per your model's fasteners
• Support the door while loosening and tightening handle screws
• Do not overtighten; align and snug evenly to avoid damage