596 78589804 Kenmore Parts

This genuine replacement door gasket creates an airtight seal around the refrigerator door to help maintain proper temperature and efficiency. It restores sealing performance to reduce frost buildup and stabilize internal cooling. What it does:

• Seals the refrigerator door edge to keep cold air in and warm air out
• Helps prevent frost and ice buildup in the freezer/refrigerator compartment
• Reduces compressor run time caused by a leaking door seal
• Improves temperature consistency for food preservation

• Disconnect power to the appliance before starting any work
• Clean and dry the door flange thoroughly before installing the new gasket
• Press the gasket into the channel evenly, working around the door to align the magnetic lip
• Inspect the seal after installation and allow normal operation to seat the gasket; check for gaps and re-seat if needed

This glass shelf replaces a damaged or missing refrigerator shelf to restore usable storage and a stable surface for food and containers. The easy-to-clean surface helps keep items visible and organized inside the fridge. What it does

• Provides a flat, stable surface for storing food, beverages and containers; replaces cracked, chipped or missing shelves.
• Restores organized storage and prevents items from shifting or falling onto lower shelves or drawers.
• Easy-to-clean glass simplifies maintenance — swap out any shelf with visible damage or instability.

• Remove all contents from the shelf area before installing; handle glass carefully and wear cut-resistant gloves.
• Slide the shelf into the existing support rails or brackets until fully seated; do not force or pry the glass.
• Reuse original clips or supports unless the manufacturer specifies replacements; verify correct orientation before seating.
• If the glass arrives chipped or cracked, do not install — stop and replace to avoid breakage or injury.

The Icemaker Fill Cup Sensor is an OEM part for Whirlpool bottom-mount and side-by-side refrigerators. Located inside the icemaker assembly, the fill cup sensor works to automatically detect when an ice scoop or bucket is in place below the icemaker chute. It signals the icemaker to drop ice cubes into the receptacle below.

Causes of a bad fill cup sensor can include mineral or dirt build-up inhibiting sensor response, moisture damage to its electronic functioning, or physical damage to the sensor head.

Symptoms of a bad fill cup sensor include:

• Ice failing to dispense or drop when a container is in place
• Ice clumping in the chute instead of dispensing properly  
• The icemaker continuing to run even with ice present below
• Inability to sense when ice is removed from the bucket

This OEM Whirlpool replacement fill cup sensor is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore bottom-mount and side-by-side refrigerators. 

This replacement agitator shaft restores the connection between the washer transmission and agitator so laundry moves properly during the cycle. Replaces a worn or damaged shaft to help eliminate agitation failure and restore normal washing action. What it does:

• Transfers rotational force from the transmission to the agitator so clothes are moved and cleaned
• Commonly replaced when the agitator refuses to move, spins freely, or washing action is inconsistent
• Can address grinding or knocking noises coming from the transmission/agitator area
• Works as a direct-fit service part when matched to the correct washer model

• Disconnect power and water before beginning any repair
• Follow the washer's service manual or OEM exploded diagram for removal and installation steps
• Inspect surrounding components (agitator, transmission seals, fasteners) and replace if worn

This wire cover protects appliance wiring from heat, abrasion and pinching to help prevent shorts and electrical faults. It's a direct-fit replacement used where wiring needs routing and protection near panels or heating components. What it does:

• Shields wiring from heat, sharp edges and moving parts to reduce wear and risk of electrical contact
• Helps prevent intermittent electrical problems caused by chafed or pinched wires
• Reduces risk of smell, burning or smoke from wires contacting hot surfaces
• Keeps wire bundles neatly routed for safer operation and service access

• One wire cover

• Disconnect power (unplug appliance or switch off circuit breaker) before servicing
• Remove access panels as needed to reach the damaged or missing wire cover
• Slide or clip the cover over the wiring harness and secure with existing fasteners; replace any damaged clips or retainers
• If wiring shows damage, replace the wiring harness or repair per manufacturer instructions before reinstalling the cover

This slide is the replacement guide that lets an oven or warming drawer open and close smoothly, restoring proper support and alignment for the drawer. Durable, low-profile fit that helps reduce sticking and uneven movement. What it does:

• Guides and supports the oven/warmer drawer during use for smooth sliding action
• Helps prevent the drawer from binding, catching, or coming off the track
• Reduces noise and uneven movement caused by worn or damaged guides
• Restores correct alignment so the drawer closes flush and operates reliably

• Disconnect power to the appliance before beginning any repair
• Remove the drawer per the appliance service instructions to access the existing slide
• Compare the new slide to the old part for proper orientation before installing
• Tighten fasteners securely and test drawer operation; do not force components

This replacement door frame trim restores the finished edge and appearance of your appliance door. It covers and protects the door opening, improving the look and helping keep the inner components protected from damage. What it does

• Replaces cracked, chipped or scratched door trim to restore a clean appearance
• Covers gaps and protects underlying door edge and gasket area from wear
• Helps prevent drafts where the door finish is damaged
• Fits and secures to the door opening for a flush, finished look

• Turn off and unplug the appliance before starting any repair.
• Remove any screws or clips holding the old trim; keep fasteners if reusable or replace if damaged.
• Align the new trim and press or fasten per the appliance's service instructions to avoid pinching the gasket.