665-158 19990 Parts

This folddown pivot is the lower hinge that lets a folddown door or panel rotate smoothly and hold position, restoring proper movement and alignment. It replaces a worn or broken lower pivot so the door or panel opens and closes correctly. What it does:

• Acts as the lower hinge point for a folddown door or panel, allowing controlled pivoting motion
• Replaces a worn, cracked, or broken pivot that causes sticking or sagging
• Helps the door/panel stay aligned and close securely instead of dropping or binding
• Commonly used when the folddown component wobbles or will not stay in the open or closed position

• Disconnect power and remove any attached panels or shelves before replacing
• Support the door/panel during removal and installation to avoid damage or injury
• Reuse OEM fasteners if undamaged or replace with equivalent hardware; ensure proper alignment during installation
• Test movement several times after installation to ensure smooth operation and secure fit

This wheel and bearing assembly mounts to the upper dishrack, allowing it to glide smoothly in and out on the rail. Replacing a worn or broken wheel restores smooth operation and helps keep the rack securely on track.

• Supports and guides the upper rack along the side rails
• Restores smooth rolling and proper rack alignment
• Helps prevent the rack from binding or derailing
• Common symptoms: rack hard to slide, falls off track, wheel cracked/missing, squeaking or grinding as the rack moves

• Disconnect power before servicing; remove the upper rack from the rails by releasing the rack stops
• Release the old wheel/bearing from the rack tabs and remove
• Snap the new assembly into the rack mounting holes until it locks
• Reinstall the rack and verify smooth travel on both rails

This dishwasher drain hose kit includes a clamp with instructions.

This small lever seal fits the dishwasher's detergent cup/dispenser. It seals around the lever/shaft to keep wash water out of the cup until the release cycle, helping deliver detergent at the right time for effective cleaning.

• Creates a watertight seal around the detergent cup lever/pivot
• Helps keep detergent dry until the main wash
• A worn or shrunken seal may allow early detergent washout or water in the cup before it opens
• Replacing the seal can help restore proper dispenser performance

• Disconnect power to the dishwasher before servicing
• Access the dispenser from the inner door; note lever and seal orientation
• Remove the old seal, clean the groove/shaft, and press the new seal fully into place
• Reassemble and run a short cycle to verify proper dispenser operation

Bottle with brush. Color: Harvest Gold. It's 0.6 fluid ounces.

This silverware basket replaces a cracked, broken, or missing utensil holder to keep forks, knives and spoons organized during the wash cycle. It fits into the dishwasher's lower rack and helps maintain cleaning efficiency. What it does

• Holds and separates silverware and small utensils so water and detergent can reach each piece
• Prevents nesting and keeps items upright for better cleaning and drying
• Secures loose items during the wash to avoid damage to dishes or the dishwasher
• Works with standard lower-rack mounting locations on compatible dishwashers

• One silverware basket

• Installs in the lower dishwasher rack; no tools required for typical replacements
• Position tines or compartments so utensils sit upright and do not block spray arms
• Do not overload the basket; bent or damaged tines may affect fit and function

This wheel leg is a replacement support used to stabilize and allow smooth movement of the appliance's lower assembly. It restores proper leveling and reduces wobble so the appliance sits securely and rolls or rests as designed. What it does

• Supports the appliance chassis at the lower corner and transfers load to the floor
• Helps maintain correct appliance height and leveling to reduce vibration and rocking
• Restores proper rolling or stationary support where a worn or broken leg caused instability
• Commonly replaced when the leg is cracked, stripped, missing, or no longer holds weight

• Verify appliance is unplugged and empty before accessing lower cabinet or base
• Support the appliance with a block or jack to prevent shifting while replacing the leg
• Remove any access panels or retaining hardware as needed; install the new leg in the original orientation
• Replace any fasteners that are damaged and test stability before returning the appliance to service

Size: 10-24 x 3/8 inch.

Electronic console assembly that houses the control interface, keypad and display so you can operate the appliance reliably. Replacing a worn or damaged console restores responsive buttons and readable display feedback. What it does:

• Provides the user interface and supports the control electronics for cycle selection and status display
• Restores button/selector responsiveness when touchpads or keys fail
• Replaces consoles with cracked bezels, unreadable displays, or non-functioning indicators
• Helps resolve issues where the control does not accept inputs or show cycle information

• Disconnect power to the appliance before starting any work to avoid shock or damage
• Handle the assembly carefully to avoid damaging the display, ribbon cables or connectors
• Some models require removal of the top or front panel to access mounting screws and electrical connectors