6651305790 Parts

This float assembly sits in the dishwasher tub and rises with incoming water to signal the float switch to stop filling. Replacing a worn or sticking overfill protector restores proper water level control and helps prevent overfilling and leaks.

• Monitors water level by floating upward as the tub fills
• Triggers the float switch to shut off the inlet valve at the correct level
• Helps prevent overfilling and potential leaks
• Helps with: won't fill or stops filling early, water level too high, float sticks or is visibly damaged

• Disconnect power and shut off the water supply before servicing.
• Remove the lower rack to access the float inside the tub.
• Lift the old float straight up; on some models a retainer under the tub must be released to remove it.
• Transfer any existing hardware if needed, install the new float, ensure free movement, then restore power and test for proper fill.

This fine mesh plastic screen filters debris from the water path to protect downstream components and help maintain proper wash performance.

• Traps fine particles to prevent clogs in the circulation/inlet path
• Helps reduce spray pressure loss and poor cleaning results
• Can address issues like gritty residue, reduced water flow, or noisy pump operation
• Wear, mineral buildup, or tearing can require replacement

• Disconnect power and shut off water before service
• Note orientation and seating of the original screen; install the replacement fully and evenly
• Inspect surrounding seals and mating parts; clean any sediment before reassembly
• Restore power/water and check for leaks and proper operation

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

The Dispenser is an OEM part for Whirlpool dishwashers. Located inside the dishwasher door, it is responsible for dispensing detergent at the proper time during cycle.

Causes of a bad dispenser can include leakage, blockages in the dispensing mechanism, door or latch issues that prevent proper opening.

Symptoms of a bad dispenser include:

• Improper or incomplete dispensing of detergent 
• Dishes not getting fully clean due to insufficient detergent 
• Leakage from the dispenser door or tub area
• Dispenser door remaining open or closed during cycles

This genuine Whirlpool part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore models as well.

Size: 8-18 x 1/2 inch.

A small metal clip that secures the appliance's ground wire to the chassis. Restores a reliable ground connection to reduce loose or arcing contacts and help prevent intermittent electrical faults. What it does:

• Secures the ground wire to the appliance frame to maintain a solid earth connection.
• Prevents a loose ground that can cause arcing, intermittent power issues, or visible sparking at the connection.
• Holds the wire in place through normal vibration and movement so terminals stay tight and stable.
• Replaces damaged, bent, or missing grounding fasteners to restore safe electrical continuity.

• Disconnect power at the breaker or unplug the appliance before inspecting or replacing the clip.
• Use proper hand tools to remove and reinstall the screw or fastener that holds the clip—do not overtighten.
• Ensure the ground wire is routed and stripped correctly; replace wiring if insulation or conductor is damaged.

Replacement clip that secures the dispenser guard on compatible Whirlpool refrigerators. Replacing a damaged or missing clip restores a secure dispenser trim and can reduce rattling or misalignment around the dispenser area. What it does:

• Secures the dispenser guard/trim to the dispenser assembly to keep the trim aligned.
• Commonly needed when the guard is loose, rattling, cracked or falls out.
• Replaces broken or missing clips that allow the dispenser trim to move or vibrate.
• Helps restore proper fit of the dispenser trim so the dispenser components sit flush.

• Disconnect power (unplug or turn off the circuit) and shut off the water supply if working near the water/ice dispenser.
• Remove the dispenser trim or guard per the model's service instructions; handle plastic parts gently to avoid cracking.
• Align the clip with the mounting slot and engage until seated; if access is limited or the guard is damaged, follow safety guidelines when servicing appliances.

This factory fastener is a #10-16 screw used to secure appliance panels and components. Replacing worn or missing hardware restores a tight fit, helps prevent rattles, and keeps parts properly aligned for dependable operation.

• Secures brackets, panels, and covers to the cabinet or frame
• Replaces missing, stripped, or corroded mounting hardware
• Helps reduce vibration and rattling from loose mounts
• Correct 10-16 thread to match designated OEM mounting points

• Disconnect power and shut off water or gas supply before servicing
• Match the screw to the original location using your model's diagram
• Start threads by hand to avoid cross-threading; tighten snugly—do not overtighten
• If replacing multiple screws, swap one at a time to maintain alignment

This dishwasher circulation pump and motor drives wash water through the spray arms for effective cleaning. Replacing a failed wash motor restores strong spray pressure and consistent cleaning performance throughout the cycle.

• Circulates water through the spray arms to wash and rinse dishes
• Maintains proper flow and pressure from the sump to all spray arms
• Direct replacement for a seized, noisy, or non-running wash motor
• Common symptoms: poor cleaning, no spray action, or humming/buzzing during wash

• Disconnect power at the breaker and shut off water supply before servicing.
• Access is from the bottom/front; many models require removing the toe panel and/or sliding the dishwasher out.
• Connect the wiring, seat the pump seal fully in the sump, and lock the assembly in place per your model's procedure.
• After reassembly, run a brief fill-and-wash to check for leaks and proper spray action.

Color: Stainless

A pronged cup washer that secures and cushions mating parts on appliances, restoring proper fit and reducing wobble. Replaces worn or damaged cup-style washers to help maintain stable component alignment and reliable operation. What it does:

• Fits into a cup or socket to hold shafts, knobs, or trim pieces in place
• Pronged design grips the mounting surface to prevent rotation and slippage
• Helps reduce vibration and noise caused by loose or worn washers
• Commonly used when a knob, shaft, or trim feels loose or wobbly

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove the related knob or trim carefully to access the washer; note orientation for correct reassembly
• Press the washer fully into the cup or socket so the prongs engage the mounting surface
• Inspect the surrounding components for wear and replace any damaged parts

This overfill switch monitors water level and signals the appliance to stop filling to help prevent overflows. Use it to restore correct water-level control when the original switch fails or malfunctions. What it does:

• Detects excess water and interrupts the fill cycle as a safety cutoff
• Works with the washer's control to maintain proper water level
• Common symptoms of a failing switch: continuous filling, overfilling, or water-level related error codes
• Can also cause cycles to stop or not advance if the machine thinks tank is overfilled

• One overfill control switch

• Disconnect power and water supply before servicing to avoid shock or flooding
• Typically located behind the control console or rear access panel
• Handle wiring connectors gently and secure all connections before testing

This inner vent gasket seals the dryer vent opening to direct hot air through the exhaust system and help maintain proper airflow. Replacing a worn or torn vent gasket restores a tighter seal and reduces air leaks. What it does:

• Seals the inner vent area to keep exhaust air flowing through the ductwork.
• Helps prevent air leaks that can cause longer dry times or uneven drying.
• Reduces lint escape and buildup around the vent opening.
• Restores proper airflow to help the dryer run more efficiently.

• Disconnect power to the appliance before starting any repair.
• Access typically requires removing panels or the drum—follow your model's service instructions.
• Inspect the mounting surface for damage or debris and clean before installing the new gasket.
• Ensure the gasket is seated evenly and not pinched during reassembly; test operation after installation.

This inner door panel replaces the appliance's damaged interior door surface to restore proper fit, protect internal components, and improve appearance. It also restores structural support and helps keep insulation and inner glass secure for reliable operation. What it does:

• Replaces the door's interior panel that supports inner glass, insulation, and internal hardware.
• Protects wiring, controls, and insulation inside the door from damage and moisture.
• Addresses common symptoms like cracked or dented inner panels, rattling or loose-feeling doors, and visible gaps between door layers.
• Restores proper door fit and interior appearance after impact or wear.

• Disconnect power (and water supply if applicable) before starting work.
• Wear cut-resistant gloves and handle any glass or sharp edges carefully.
• Retain and reuse original fasteners when possible; align the panel before fully tightening screws.

This dispenser cover is the replacement lid for a washer dispenser assembly, restoring a secure, functional cover that keeps detergent and fabric softener contained until the wash cycle. It helps prevent spills and keeps the dispenser looking finished. What it does:

• Replaces a cracked, warped, or missing dispenser lid so the dispenser closes properly
• Helps contain detergent and softener to prevent drips and spills onto the washer top
• Restores a flush, finished appearance to the dispenser area
• Works with the dispenser housing to ensure proper release of cleaning agents during cycles

• Disconnect power and water supply before servicing the washer
• Replacement typically installs with clips or screws; keep original fasteners and note their placement
• Handle plastic parts carefully to avoid cracking; align tabs before snapping into place

Color: Biscuit. Size: 13 oz. can. Enamel spray paint.