7957414 Parts

This DC motor restores the appliance's drive function by replacing a worn or failed motor assembly. Installing the correct motor helps stop drive-related failures and returns reliable rotation and operation to the unit. What it does:

• Provides the rotational drive that powers the appliance's moving components.
• Restores normal starting and running when a failed motor causes no rotation or intermittent operation.
• Stops or reduces humming, grinding, or unusual noises coming from the drive area.
• Works with the appliance's control system to maintain correct speed and response.

• Disconnect power before starting any repair to avoid shock or injury.
• Handle the motor and electrical connectors carefully; secure wiring and mounting fasteners per the service manual.

This micro switch is a compact, snap-action electrical switch that sends an on/off signal when a lever, latch, or paddle is moved. Replacing a worn switch restores reliable detection and control response for the affected function.

• Converts mechanical movement into an electrical open/close signal to the control
• Commonly used for lever/paddle actuators, latches, or interlock detection within the appliance
• Safe symptom clues: no response when actuated, intermittent operation, or a function stuck on/off
• Physical clues: weak or absent "click" when pressed, heat discoloration or damage at terminals

• Disconnect power before servicing; if the product is connected to a water line, close the supply valve
• Note wire positions and terminal labels (COM/NO/NC); transfer wires one at a time to matching terminals
• Match the actuator orientation and mounting position to the original for proper operation
• After installation, verify continuity with a multimeter and test function before reassembly

Left side upper hinge.

This replacement door gasket creates a heat-resistant seal between the oven door and the front frame. A tight seal helps the oven maintain temperature and cook evenly while keeping heat from escaping into the kitchen.

• Seals the oven cavity to reduce heat loss and temperature fluctuations
• Helps improve preheat times and baking performance
• Worn seals can cause heat leakage, longer cook times, or hot air felt around the door
• Cracks, flattening, or fraying indicate the gasket should be replaced

• Disconnect power before servicing; allow the oven to cool completely
• Open the door and carefully release the old gasket from its mounting clips
• Align and press the new gasket into the channel, seating each clip fully
• After installation, check for even contact around the door

This replacement hinge assembly supports and pivots the refrigerator door. Replacing a worn or bent hinge restores smooth door movement and proper alignment so the gasket can seal correctly to help maintain performance. What it does:

• Provides the pivot point for the door to open and close
• Supports the door's weight to keep it aligned
• Helps the door gasket seal evenly against the cabinet
• May correct issues such as door sagging, rubbing, popping, or not closing/sealing fully

• One hinge assembly

• Unplug the refrigerator and remove items from the affected door
• Support the door while removing hinge screws; note the orientation of any spacers/bushings
• Transfer any reusable hardware from the old hinge to the new assembly
• Reinstall and tighten fasteners; verify door is level and check gasket seal

This display control board assembly is the electronic PCB for the appliance's user interface. It powers and manages the front-panel display and buttons so settings respond correctly and status information is shown as designed.

• Drives the display/indicators and provides regulated power to the user interface
• Interprets button/touch inputs and relays commands to the main control
• Coordinates communication between the UI and control system for proper operation
• Typical symptoms: blank or dim display, unresponsive buttons/keys, erratic characters/segments, or intermittent UI power

• Disconnect power before servicing; observe ESD precautions when handling the board
• Photograph wiring and label connectors; fully seat any ribbon cables
• Transfer any mounting hardware, standoffs, or cosmetic lens/overlay from the original board if required
• After installation, restore power and test all UI functions

This self-tapping screw fastens panels, brackets, and internal components in compatible appliances. Replace a stripped, corroded, or missing screw to restore a secure fit and help prevent vibration, rattling, and misalignment.

• Forms/engages its own threads in sheet metal or plastic for a secure hold
• Secures covers, brackets, and assemblies to maintain alignment
• Helps reduce vibration and noise from loose components
• Replace if the head is stripped/broken, threads are worn, or the screw is missing

• Disconnect power and shut off water or gas, as applicable, before servicing
• Match to the original location and hardware; use identical length and thread where specified
• Start by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving hole is damaged, repair it before installing the new screw

This door gasket assembly restores the door seal so the appliance holds a tight, reliable seal during use. Replacing a damaged gasket helps stop leaks and maintain consistent temperatures for proper operation. What it does:

• Forms the seal between the door and cabinet to prevent water/vapor or air loss
• Stops common symptoms such as visible leaks, moisture around the door, or poor temperature retention
• Replaces torn, stretched, or hardened gaskets that no longer seat properly
• Helps the appliance run more efficiently by restoring the intended seal

• Disconnect power (and water if applicable) before starting any repair
• Inspect the door and mounting channel for damage or debris; clean surfaces before installing the new gasket
• Seat the gasket evenly around the full door perimeter and secure any retaining clips or screws per OEM guidance

This holder assembly is a structural mounting piece that supports and secures an internal component in your appliance. Replacing a cracked or worn bracket helps restore proper alignment and keeps parts stable during everyday use.

• Provides a rigid mounting point for the attached component
• Keeps parts aligned to reduce movement and vibration
• Helps prevent rattling or noise from loose mounts
• Common signs of failure: visible cracks/broken tabs, looseness, or parts that won't stay seated

• Disconnect power and, if applicable, turn off the water supply before service
• Note the orientation of the original part to match fitment
• Reuse existing mounting screws or hardware unless the manufacturer specifies otherwise
• Do not overtighten fasteners; the secured component is fully seated and stable

This tube assembly directs water through the appliance, restoring a secure, leak-resistant path when the original line is brittle, kinked, or damaged. Replacing it helps stop leaks and restores normal water flow.

• Routes water from the inlet valve to internal components
• Maintains sealed connections to reduce drips and seepage
• Replaces tubing that is cracked, kinked, or clogged with mineral deposits
• Common symptoms: visible leaks, puddling, low flow, or intermittent water delivery

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water and relieve line pressure
• Note the routing and connection points; transfer any retainers from the old part if needed
• Insert tubing fully into fittings and tug gently to confirm engagement; restore water and check for leaks

This replacement screw secures specified panels or components inside your appliance. Refreshing worn or missing hardware helps restore a tight fit, reduce rattling, and keep assemblies properly aligned for reliable performance.

• Provides secure fastening for brackets, panels, or internal assemblies
• Replaces stripped, rusted, or lost hardware
• Helps reduce vibration and rattling noises
• Symptoms include loose panels, shifting components, or a screw that won't tighten

• Disconnect power and allow any hot surfaces to cool before servicing
• Wear cut-resistant gloves and eye protection
• Match length and thread to the original; replace like-for-like
• Start threads by hand to avoid cross-threading; do not overtighten

This ice gear transfers motor rotation to the refrigerator's ice mechanism so cubes can be dispensed or ejected. Replacing a worn or stripped gear restores smooth, reliable ice operation and helps eliminate grinding or clicking noises.

• Transfers drive from the motor to the ice mechanism (auger/ejector, depending on model)
• Helps move ice through the system for dispensing or harvest
• Common symptoms: no or slow ice dispensing, auger not turning, loud clicking/grinding from the ice bin
• Cracked or stripped teeth indicate the gear should be replaced

• Disconnect power to the refrigerator before servicing
• Remove the ice bin and access the ice assembly per your model; note gear orientation for reassembly
• Align teeth carefully; do not force the gear onto the shaft
• Inspect related parts (drive coupler, auger, motor shaft) and replace any worn components to prevent repeat failure

STOPPER ASSEMBLY,DOOR

This sub PCB assembly is an electronic control board that processes inputs and switches components, coordinating specific appliance functions. Replacing a failed board can restore normal operation and resolve dead controls, error codes, or intermittent, unpredictable behavior. What it does:

• Distributes and regulates control power and switches loads via onboard relays/triacs
• Interprets signals from sensors and the user interface to execute commands
• Coordinates timing and operation of related components per the appliance's program logic
• Failure may present as no power, won't start, unresponsive or flickering display, random beeps, or recurring error codes

• 1 sub PCB assembly

• Disconnect power to the appliance before servicing; verify no voltage is present
• Use ESD protection and handle the board by the edges
• Photograph wiring; transfer connectors one at a time and ensure they are fully seated
• Secure the board with existing fasteners/standoffs; perform any required reset or diagnostic per your model's service info

This gas valve assembly controls and shuts off the flow of gas to your appliance's burner system, enabling safe ignition and steady heat. Replacing a sticking or failing valve restores reliable heating performance and consistent flame control.

• Regulates gas flow to the burner(s) as commanded by the control/thermostat
• Works with the igniter to light the flame
• Helps maintain stable gas supply for consistent heating
• Failure symptoms include no ignition, igniter glowing with no flame, intermittent heat, or a weak/uneven flame

• Disconnect power and shut off the gas supply before servicing
• Allow the appliance to cool and work in a well-ventilated area
• Transfer any fittings or brackets from the original valve if required
• After installation, restore gas and check all connections for leaks with a soapy-water solution