8573240 Parts

This clamp secures flexible hoses to fittings to maintain a tight seal and prevent leaks. Use it to replace a worn or loose clamp to stop water or air seepage and restore proper hose attachment. What it does:

• Holds a washer, dryer, or appliance hose firmly to a barb or fitting to prevent slipping
• Helps maintain a watertight or airtight connection to reduce leaks and drips
• Replaces corroded, cracked, or stretched clamps that no longer grip reliably
• Supports normal appliance operation by keeping fluid/air flow contained

• One clamp

• Inspect the hose and fitting; replace the hose if damaged before installing the clamp
• Position clamp over the hose barb and tighten evenly; avoid over-tightening that can cut the hose
• Disconnect power and water supply before servicing any appliance components

This is a replacement screw used to secure appliance panels and components. It restores proper fastening so panels, trim, or assemblies stay tight and reduce vibration or rattling. What it does

• Fastens panels, brackets, or trim to the appliance chassis
• Helps stop loose or vibrating panels and trim pieces
• Restores proper alignment where a missing or stripped screw causes gaps or movement
• Use when the original screw is missing, damaged, or corroded

• One replacement screw as shown

• Disconnect power to the appliance before starting any repair
• Use the correct screwdriver or bit to avoid stripping the screw head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Keep removed screws in a safe place; this screw matches the original before installation

This pump gasket seals the connection between the appliance pump and housing to help prevent leaks and keep water flowing where it should. A simple replacement that restores a watertight pump interface. What it does:

• Creates a tight seal at the pump housing to stop water from leaking
• Helps maintain proper drain flow by preventing bypass leaks
• Commonly replaced when you see puddling or moisture under the appliance
• Can prevent intermittent draining issues caused by a compromised seal

• One pump gasket

• Disconnect power and water supply before starting any repair
• Inspect mating surfaces and clean debris before installing the new gasket
• Ensure the gasket seats fully and pump/housing fasteners are torqued to spec

This O-ring is a small rubber sealing gasket that prevents water leaks at a refrigerator water connection. It restores a watertight seal to stop drips and maintain proper water flow to the dispenser/ice system. What it does:

• Creates a watertight seal at a water line or valve connection
• Helps stop visible dripping or slow leaks from fittings
• Maintains proper pressure and flow by preventing bypass around a joint
• Used where a compressible seal is required between two mating parts

• Shut off water supply and disconnect power before servicing
• Replace only with the correct-size O-ring and seat it evenly in the groove
• Inspect mating surfaces for nicks or debris; clean before installing the new O-ring
• Tighten fittings to manufacturer torque recommendations to avoid over-compression

This replacement door gasket creates a tight seal around the refrigerator door to help maintain proper cooling and reduce energy waste. It restores the door's sealing surface for more consistent temperatures and less moisture buildup. What it does:

• Seals the door perimeter to keep cold air in and warm air out
• Helps prevent frost and ice buildup inside the compartment
• Reduces excessive run time from the compressor caused by air leaks
• Minimizes condensation and food spoilage linked to poor door sealing

• Disconnect power to the appliance before starting any work
• Remove the old gasket and clean the gasket channel and mounting surface
• Align and seat the new gasket evenly around the door; start at corners for best fit
• After installation, allow the gasket to set and check for gaps; adjust as needed

This wash impeller is the pump rotor that moves dishwasher wash water through the circulation system to help clean dishes. Replacing a worn impeller restores proper water flow and improves cleaning performance. What it does:

• Spins on the wash pump shaft to push water through spray arms for effective cleaning
• Helps maintain proper spray pressure during the wash cycle
• Worn or damaged impeller can cause weak spray, poor cleaning, or unusual pump noise
• Works with the pump housing and seals to keep water circulating where it belongs

• One wash impeller

• Disconnect power and water supply before beginning any repairs
• Access the lower pump assembly by removing the lower access panel and spray arm(s)
• Inspect pump housing and seals; replace any damaged gaskets to prevent leaks
• Reassemble carefully and run a test cycle to check for proper operation and leaks