970C653520 Parts

No.8 pan head `10 - 10b x 0.50 `cr/sq drive

This suspension spring supports the washer tub and helps stabilize the drum during spin cycles to reduce vibration and noise. Replaces a worn or broken tub spring to restore smoother operation. What it does

• Holds and stabilizes the inner tub assembly to limit excessive movement during spins
• Helps reduce vibration and rattling that can occur from a loose or broken spring
• Prevents tub misalignment that can cause rubbing or noise
• Works with the washer's suspension system to maintain proper spin balance

• One suspension (tub) spring as shown

• Disconnect power and water supply before starting any repairs
• Springs are under tension; use caution and proper tools to remove/install
• Inspect other suspension components (shocks/rods, mounts) and replace if worn

Self leveling leg pad

Ceramic dryer heating element housing insulator.

This is a timer that is used on washing machines. It controls the electrical components and the length of time of the washing machine's cycles. Be sure to unplug the appliance from the electrical outlet before beginning repairs. Some people performing the replacement or repair may wish to wear work gloves to protect their hands. The replacement process only takes about ten minutes to complete from start to finish.When the timer will not advance, it is likely that the washing machine cycles will not run at all or won't run consistently. The appliance may not advance through the various cycles like the washing, rinsing, and spinning cycles and may get stuck on one of the cycles. This timer is compatible with washing machines that are manufactured by Kenmore, Gibson, Westinghouse, and Frigidaire. It is sold individually and is sourced directly from the manufacturer and a genuine OEM part.

The Cord is an OEM replacement part for Frigidaire washing machines. Extending from the rear of the unit, it safely powers the washer through a connection to a wall outlet.

Causes of cord failure are normal wear from frequent coiling and plugging/unplugging motions over the appliance's lifespan. Rodents or sharp edges may also damage the outer jacketing.

Signs of a bad cord include:

• Exposed or severed copper wiring visible inside
• External cracks, splits or abrasions eroding the casing  
• Erratic behavior during the wash cycle
• GFCI/EGCI outlet tripping frequently

Compatible models also include Electrolux, KitchenAid, Jenn-Air, and Kenmore options. Maintaining safety is a top priority.

This is a motor-mount screw used to secure the appliance motor housing. It's a direct-fit fastener that restores proper motor attachment to reduce movement and rattling caused by loose or missing hardware. What it does:

• Secures the motor to its mounting bracket or housing
• Prevents motor shifting that can cause vibration, noise, or misalignment
• Restores proper mechanical connection after strip-out or lost hardware
• Helps maintain safe operation by keeping motor fastened

• Disconnect power before servicing the appliance.
• Use the correct screwdriver or socket to avoid stripping the head.
• Thread carefully and tighten to snug; avoid over-tightening which can strip threads.
• If mounting holes or threads are damaged, repair or replace the affected components before reinstalling.

This is a replacement mounting screw used to secure appliance panels, brackets, and components. Replacing worn or missing screws restores proper fit and reduces rattles or loose parts for safe, stable operation. What it does:

• Secures panels, brackets, trim, or small components in place
• Helps eliminate rattling, vibration, and loose or misaligned parts
• Restores proper fastening after maintenance or part replacement
• Matches the appliance's original fastener style for correct fit

• Disconnect power to the appliance before servicing to avoid shock or injury
• Use the correct driver bit to avoid stripping the head
• Do not overtighten; snug until secure to prevent thread or component damage

This dispenser valve assembly controls water flow to the fridge door dispenser for reliable dispensing and shutoff. It replaces a failed valve to restore proper water delivery and stop unwanted dripping or leaks. What it does

• Opens and closes the water passage when the dispenser actuator is pressed to deliver water to the glass.
• Seals the water line to prevent drips or continuous flow when the dispenser is idle.
• Helps stop intermittent dispensing or no-water issues caused by a faulty valve.
• Works with the door dispenser plumbing—electrical/connectors remain unchanged.

• Disconnect power and shut off the refrigerator water supply before starting.
• Remove the refrigerator door panel or access cover per your model's service instructions to reach the valve.
• Verify electrical connector seating and water line fittings are secure; replace any damaged tubing or seals.
• Test for leaks and proper dispensing after restoring power and water.

Replacement mounting screw that secures appliance panels, trim or brackets to restore proper fit and reduce rattles. A simple fastener that helps keep components stable for safe, quiet operation. What it does:

• Secures panels, trim pieces or internal brackets in place
• Replaces lost, stripped or damaged screws that cause loose parts
• Helps stop rattling, vibration or misaligned panels
• Restores proper alignment so doors and covers sit flush

• Use the correct screwdriver or bit to avoid stripping the head
• Do not overtighten — snug until secure to prevent damage
• Disconnect power before working near electrical components
• Keep small parts away from children and pets

A replacement hex washer head screw that secures appliance panels and components. Durable hardware designed to match OEM fit so you can restore proper fastening and reduce rattling or loose parts. What it does:

• Fastens panels, brackets, and assemblies where a 1/4-20 thread is specified
• Provides a built-in washer head to distribute load and resist pull-through
• Commonly used where vibration or movement can loosen standard screws
• Helps stop rattling, misalignment, or loose trim caused by missing or stripped fasteners

• Use the correct screwdriver or socket to avoid stripping the head; tighten until snug, do not over-torque
• Replace any damaged mating hardware or worn threads for a secure fit

One per package.

This genuine OEM part is a washer lid. The washer lid is the main piece that covers the washer. Over time, a washer lid can become damaged to the point where it no longer closes securely. If the washer lid is no longer closing all the way or is severely cracked or damaged, it will need to be replaced.To replace this part, start by making sure the washer is unplugged. After it has been powered off, proceed to take a putty knife to lift to release the two retaining clips that secure the washer's main top. Once released, proceed to remove the lid lock assembly wire connector. Fully remove the main top and set it upside down. Release the tension on the lid springs and detach the springs from the main top and hinge bars. Using a Phillips head screwdriver, remove the screws that secure the hinge bars to the lid. Push the hinge bars through the bearings then twist the bars to remove them. This will separate the lid from the main top. Take the new lid and align it with the main top. Insert the hinge bar between the main top and bearing while threading the screws to secure the new top. Reinstall the top panel and connect the wire harness. This replacement part is sourced directly from the manufacturer and is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse brand washers.

This hex washer head screw secures appliance components and hardware, helping keep panels and assemblies fastened for safe, reliable operation. Use it to replace missing or damaged screws that allow parts to shift or rattle. What it does:

• Fastens panels, brackets, and component assemblies using a hex washer head for broad bearing surface
• Restores secure fit where stripped, missing, or damaged screws cause loose parts or vibration
• Maintains proper alignment and prevents movement that can lead to noise or additional wear
• Matches the OEM thread and length for a correct fit when replacing the specific factory screw

• Disconnect power to the appliance before beginning any repair
• Use the correct hex driver/socket to avoid stripping the head
• Thread the screw in straight and tighten until snug; avoid overtightening
• Repair or replace the threaded insert or mounting hardware before installing

This white replacement plug fills and finishes an unused opening on the appliance, helping keep out dust and debris while restoring a clean, factory appearance. Use it where a small trim or access hole needs a discreet cover. What it does:

• Covers unused holes or access slots to protect internal components from dust and moisture
• Restores a finished, factory look to trim panels or consoles
• Helps prevent small items from falling into openings
• Simple, low-profile piece that stays recessed and unobtrusive

• No power required; work with the appliance unplugged or power turned off as a safety precaution when accessing trim
• Push the plug into the opening until it seats flush; a gentle push with a finger or soft tool is usually sufficient
• If removal is needed later, gently pry with a flat, non-marring tool to avoid scratching surrounding surfaces