Gfws1700howw Parts

The Knob is an OEM replacement part for GE washers and dryers. It is a crucial component that allows users to select and control various settings.

Symptoms of a faulty knob include:

• Difficulty turning or selecting desired settings
• The knob feeling loose or wobbly
• The knob falling off or becoming detached from the control panel

Causes of a bad knob can include normal wear and tear over time, physical damage from impact or mishandling, or issues with the internal mechanism or hardware that secures the knob in place.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models. 

The GE pump is an OEM replacement part responsible for removing wastewater from the washing machine during the drain cycle. It pumps out the soiled water from the washer's tub, ensuring that it is expelled through the drain hose and into the plumbing system or utility sink. The pump consists of an electric motor and an impeller that move the water effectively.

Causes of a bad pump can include clogging from debris or lint, wear and tear from regular use, or damage to the pump impeller or motor. Exposure to harsh chemicals or overloading the washer can also contribute to pump failure.

Symptoms of a bad pump include:

• Water not draining from the washer
• Unusual noises such as humming or grinding during the drain cycle
• Error codes related to drainage issues
• Water leaking from the bottom of the washer

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The 2 In 3 Out Water Valve is an OEM replacement part for GE washing machines. It is located within the water supply system to help regulate water flow into the washer tub. 

Causes of failure can include obstruction or clogging from mineral deposits over time. Valve components may also wear out with extended usage.

Symptoms of a faulty water valve include:

• Extended or interrupted cycle times 
• Fluctuations in water levels inside the tub
• Weak water pressure levels for filling and rinsing  
• Leaks from the water inlet area of the washer

Compatible models include GE, Hotpoint, RCA, and select Kenmore models.

The Door Plunger is an OEM part for GE washing machines. This part ensures the door is securely latched during the wash cycle.  

Causes of a bad Door Plunger can include wear and tear from frequent use, physical damage from accidental impacts, or deterioration due to exposure to moisture and detergent over time.

Symptoms of a bad door plunger include:

• The washer door not latching properly
• The washing machine stopping mid-cycle
• Water leaking from the door area
• Error messages related to door locking mechanisms

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Shock Damper is an OEM part for GE washing machines. It plays a crucial role in minimizing vibrations and absorbing shocks during the wash cycle, ensuring the washer operates smoothly and quietly. The shock damper helps stabilize the drum, preventing excessive movement and reducing wear on other components.

Causes of a bad shock damper can include repeated exposure to heavy loads, unbalanced loads that exert extra pressure, and general wear and tear over time.

Symptoms of a bad shock damper include:

• Excessive shaking or vibrating during the wash cycle
• Loud banging or knocking noises
• The washer moving or shifting during operation
• Leaks due to increased stress on the tub and other components

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Door Lock is an OEM part for GE washing machines. This part secures the washer door during operation, ensuring that it remains closed and sealed tightly. The door lock prevents the door from being opened while the machine is running, providing safety and maintaining the integrity of the wash cycle.

Causes of a bad door lock can include electrical issues such as short circuits or wiring problems, mechanical wear and tear from frequent use, and physical damage from forceful closing or opening of the door.

Symptoms of a bad door lock include:

• The washer not starting or advancing through cycles
• Error codes related to the door lock
• The door not locking or unlocking properly
• The washer stopping mid-cycle due to door lock issues

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Driving Belt is an OEM part for GE washing machines. This part connects the motor to the drum, facilitating the drum's movement during the wash and spin cycles, ensuring your laundry is cleaned effectively.

Common causes of a bad driving belt include normal wear and tear, overloading the washer, or exposure to high heat or friction. 

Symptoms of a bad Driving Belt include:

• Drum not spinning or agitating
• Washer making unusual noises during operation
• Burning smell from the washer
• Visible cracks or wear on the belt

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Drive Pulley Kit is an OEM part for GE washing machines. The drive pulley works by transferring the motor's power to the drum via the drive belt, ensuring the drum rotates properly during the wash and spin cycles.

Causes of a bad drive pulley can include wear and tear over time, damage due to overloading the washer, or issues such as misalignment or loose components.  

Symptoms of a bad drive pulley include:

• Loud, unusual noises during operation
• The drum not spinning or agitating
• The washer not completing cycles properly
• Visible damage or wear on the pulley

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This suspension spring supports and stabilizes the washer tub, controlling movement during wash and spin. Replacing a weak or broken spring helps restore balance, reduce vibration, and prevent the tub from leaning or striking the cabinet.

• Supports the tub assembly within the cabinet and carries load
• Limits tub motion to reduce shaking and out-of-balance interruptions
• A stretched or broken spring can cause excessive vibration, banging, or a low/leaning tub
• Visual signs include broken coils or uneven tub height

• Disconnect power; turn off water and move the washer for safe access
• Springs are under tension—support the tub and wear hand/eye protection
• Note the original spring's location and orientation; reinstall in the same position
• After replacement, ensure the tub sits level and clears the cabinet on all sides

This diverter valve directs wash water inside the machine, switching flow between internal paths during wash and drain/recirculation steps. Replacing a failed diverter restores proper water routing so cycles advance and complete as designed.

• Redirects water between the drain and recirculation/spray paths as commanded by the control
• Ensures correct water flow for wash, rinse, and drain steps
• A sticking or failed diverter can cause slow/no drain or no recirculation/spray
• May lead to cycle pauses/errors, unusual clicking/buzzing from the valve area, or leaks at the valve body/ports

• Unplug the washer and turn off water supply; expect residual water in hoses
• Access location varies by model; typically mounted along the pump/hoses under the cabinet
• Move hoses/clamps and the electrical connector one at a time; match port orientation
• After installation, run a rinse/drain test and check all connections for leaks

This outer door gasket clamp secures the washer's door boot to the front panel, keeping the seal tight around the door opening to help prevent leaks and keep the gasket seated during operation.

• Holds the outer lip of the door gasket (boot) against the front panel
• Helps maintain a watertight seal at the door opening
• Replace if the clamp is bent, stretched, broken, or missing
• Symptoms include the boot slipping off, water leaking at the front, or a loose gasket

• Disconnect power and wear cut-resistant gloves for safety.
• Open the door, gently pull back the gasket, and remove the old outer clamp.
• Ensure the gasket is fully seated on the front panel lip, then install the new clamp evenly around the opening.
• After installation, run a short cycle and check for leaks around the door.

This drain hose coupling joins two sections of a washer's drain hose to create a secure, leak-resistant connection. Replace a cracked or loose connector to help prevent leaks and support proper draining performance. What it does

• Connects two drain hose sections for proper water discharge
• Maintains a tight, sealed joint to help prevent leaks at the hose connection
• Restores a secure hose path if the original coupling is cracked, worn, or missing
• Common symptoms: water on the floor during drain, loose hose connection, or hoses separating

• Drain hose coupling

• Disconnect power and turn off water before servicing; pull the washer forward for access
• Place a towel or pan to catch residual water from hoses
• Loosen hose clamps, remove the old coupling, fully seat both hose ends on the new coupling, and tighten clamps securely
• Run a brief drain/rinse and inspect the connection for leaks

Hinge Leaf secures a refrigerator or freezer door at the hinge point, providing a stable mounting surface that helps the door stay aligned and open/close smoothly — reducing sag and uneven gaps. What it does:

• Secures the hinge pin and fastens the door to the cabinet at the hinge location.
• Maintains door alignment to help ensure even sealing and proper closing.
• Helps correct common door problems like sagging, binding, or uneven gaps.
• Works with existing hinge hardware to restore hinge stability when the leaf is worn or damaged.

• Disconnect power (unplug or switch off circuit) and remove food/contents from the door before starting.
• Support the door while removing hinge fasteners to prevent the door from dropping or shifting.
• Use appropriate hand tools and keep original screws/hardware unless replacing.

This OEM replacement part is a seal gasket used for washers. The seal gasket is the rubber seal that goes outside the washer tub that seals to the washer door. If the seal is cracked or otherwise damaged to the point where the washing machine door no longer opens and shuts properly, it might be time for a replacement. Luckily replacing this seal gasket is a relatively easy fix.To replace this part, start by shutting off power to the washing machine. Open the washer door and remove the mounting screws that hold the seal in place. Once removed gently lift the seal out of its place and proceed to replace it with the new seal gasket. Once fitted, secure the seal with the mounting screws and make sure it fits tightly. Close the washer door to make sure it is completely sealed.This genuine replacement part is compatible with GE, Hotpoint, and RCA brand washers.

This outside drain hose directs wastewater from your washer to the household drain. Replace a cracked, kinked, or leaking hose to stop leaks and restore reliable draining at the end of each cycle.

• Routes discharge water from the drain pump to a standpipe, laundry tub, or sink
• Helps maintain proper flow during drain/spin to prevent backups
• Common signs of failure: water leaking behind the washer, slow or incomplete draining, or drain-related error messages
• Visual clues include cracks, pinholes, bulges, or severe kinks

• Disconnect power and water; pull the washer forward for access and place towels/bucket as needed
• Note hose routing and connection points; release clamps and remove the old hose
• Fully seat the new hose; reuse existing clamps/hangers as required. Route without kinks and maintain proper standpipe height
• Run a test drain/rinse and check all connections for leaks

The Washer Door Glass is an OEM part for GE washers. This glass serves as a protective barrier while allowing you to observe the washing process inside the machine. The door glass is designed to withstand the rigors of regular use and maintain transparency for a clear view of your laundry.

A bad door glass can occur due to accidental breakage or cracks over time. If you notice signs of damage, such as shattered or missing pieces, it may be time to replace the door glass.

Symptoms of a bad door glass include:

• Shattered or broken glass
• Visible cracks or chips
• Inability to see through the glass

Restore the function of your GE washer by replacing the damaged door glass with this genuine part. This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.