Amana Ntw4601bq1 Parts

This replacement power cord restores the appliance's primary electrical connection so it can receive power safely. Use it when the original cord is damaged, frayed, or no longer providing a reliable connection. What it does:

• Provides the main incoming electrical connection from the wall outlet to the appliance
• Replaces cords with visible damage, exposed wiring, or intermittent power delivery
• Can resolve no-power or power-interruption symptoms when the cord is the fault
• Ensures a secure connection when installed with the correct strain relief and terminal fastening

• Disconnect the appliance from power before attempting any service.
• Remove access panels as needed to reach the cord terminals; note wire locations before disconnecting.
• Secure cord with the appliance's strain relief and tighten terminal connections per the factory layout.

This cabinet is the main outer housing that supports and protects the appliance's internal components while giving the unit its finished exterior. It restores structural integrity and proper panel alignment for safe, reliable operation. What it does:

• Provides the structural frame and mounting surface for controls, panels, and internal components
• Protects internal parts from dust, moisture, and incidental contact
• Helps maintain proper airflow and component positioning to reduce vibration and noise
• Restores correct panel alignment and closure when the original cabinet is dented, cracked, or corroded

• One cabinet

• Disconnect power (and gas, if applicable) before beginning any repair
• Installing may require removing trim, controls, and internal components; keep fasteners organized
• Use proper lifting technique and a second person for heavy or bulky cabinets to avoid damage or injury

This tub ring mounts at the top of the outer tub to contain splashes and suds during agitation and spin, helping prevent over-the-rim leaks. Replace a cracked or broken ring to restore proper water containment and fit.

• Acts as the upper splash shield for the outer tub
• Helps keep wash water and suds from escaping during operation
• Secures with locking tabs for a tight, even fit around the tub opening
• Typical signs of failure: cracks, broken/missing tabs, water or suds at the top of the tub

• Disconnect power and water; wear gloves and eye protection
• Lift or remove the top/console to access the tub opening
• Release retaining clips/tabs, remove the old ring, and clean the tub rim
• Align and snap the new ring evenly into place; confirm all tabs are fully seated before reassembly

This leveling foot threads into the base of your appliance to support and stabilize it. Adjusting the foot helps level the cabinet, reduce wobble and vibration, and keep doors aligned for smooth, reliable operation. Also called a leveling leg. What it does:

• Provides an adjustable contact point to stabilize the unit on the floor
• Helps level the cabinet so doors align and seal properly
• Reduces rocking, rattling, or excessive vibration on uneven surfaces
• Replaces a cracked, stripped, or missing leveling leg

• 1 leveling foot

• Unplug the appliance and turn off water supply if applicable
• Use a helper to carefully move or tilt the unit; support it securely
• Unthread the damaged foot; thread in the new foot by hand, then fine-adjust with a wrench
• Level side-to-side and front-to-back; ensure all feet make firm floor contact

This clamp secures a washer or dryer hose to its connection to prevent leaks and keep the hose firmly in place during operation. It replaces worn or loose clamps that allow water to escape or hoses to detach. What it does:

• Holds a washer/dryer hose to a nipple, collar or fitting to maintain a sealed connection
• Prevents water leaks caused by loose or corroded clamps
• Stops hoses from slipping off during drain or fill cycles
• Restores proper hose retention and reduces risk of water damage

• Disconnect power and turn off the water supply before starting any repair
• Inspect hose and fitting for damage; replace hose if cracked or frayed
• Use appropriate pliers or a screwdriver for the clamp style; avoid overtightening to prevent hose damage
• Verify a leak-free connection after restoring power and water

This genuine replacement screw secures components in compatible Whirlpool appliances, restoring proper fit and preventing rattles or loose panels. Use it when original fasteners are missing, stripped, or damaged. What it does:

• Fastens panels, brackets or small components to maintain structural stability
• Replaces missing or worn screws that cause vibration, rattling, or loose parts
• Restores secure connections after repairs or part replacements
• Helps prevent further damage by keeping parts properly aligned

• Turn off and unplug the appliance before servicing to avoid shock or injury
• Use the correct screwdriver or bit to avoid stripping the head
• Thread carefully and hand-start the screw to prevent cross-threading
• Keep small parts away from children and pets during installation

Replacement top for a 27-inch laundry appliance. Restores a secure, finished cover for the cabinet, protecting internal components and improving the appliance's appearance after damage or wear. What it does:

• Covers and protects internal components at the top of the cabinet.
• Provides a stable mounting/seat for the control console and trim.
• Prevents debris and moisture from entering the appliance chassis.
• Restores a flush, finished look when the original top is dented, bent, or corroded.

• Disconnect power before beginning any service.
• Support the cabinet and use proper tools to remove the control panel or hinges as needed.
• Handle the panel carefully to avoid sharp edges; align and fasten all mounting points securely.

Kit contains two 10 feet inlet hoses.

This replacement brace reinforces appliance cabinet structure to restore proper alignment and reduce vibration. It helps maintain secure mounting of adjacent panels so doors and controls operate smoothly. What it does:

• Provides structural support for the appliance cabinet and connected panels
• Reduces rattling or vibration caused by loose or bent cabinet components
• Helps realign panels that are pulling away or not closing flush
• Useful when visible damage, bending, or missing support causes fitment issues

• Disconnect power and, if applicable, gas supply before starting any repair
• Remove outer cabinet panels or access panels to reach the brace mounting points
• Retain original fasteners when possible; replace damaged screws or clips as needed