Bkef3048ls Parts

Replacement glass panel for the oven door. It restores a clear viewing window and helps maintain proper insulation when the original glass is cracked, shattered, or discolored.

• Forms the see-through window in the oven door
• Contributes to the door's thermal barrier to help maintain set temperature
• Replace if the glass is cracked, shattered, fogged, or has sharp edges
• Improves visibility and refreshes the appliance's appearance

• Disconnect electrical power; shut off gas supply for gas ranges
• Allow the oven to cool completely; wear cut-resistant gloves and eye protection
• Support the door and remove it if required; transfer any trim/retainers from the old glass
• Handle glass by the edges only and avoid overtightening fasteners during reassembly

This factory screw secures panels, brackets, and other components in your cooking appliance. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and keep parts properly aligned during use.

• Fastens components to maintain proper alignment and stability
• Helps prevent vibration, rattling, and loose parts during operation
• Replace if threads are stripped, the head is damaged, or the screw is missing
• Commonly used to mount internal or exterior parts in ranges and wall ovens

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Use the correct driver bit to avoid stripping the screw head
• Install in the original location and do not overtighten
• If the receiving threads are damaged, repair or replace the mating part before installation

This lower drawer replaces a damaged or missing bottom drawer on your range, restoring smooth slide action and a flush, finished look so the lower compartment operates correctly and the appliance is complete again.

• Forms the pull-out compartment beneath the oven for convenient access
• Interfaces with the drawer slides to open and close smoothly
• Restores proper alignment and full closure at the base of the range
• Typical symptoms: drawer jams, falls off tracks, sits unevenly, or is bent/dented

• Disconnect power and shut off gas; allow the range to cool before servicing
• Pull the old drawer out and lift to disengage from the slides; transfer any reusable parts as needed
• Set the new drawer onto both slides evenly and test for smooth travel and full closure
• If the drawer doesn't seat flush, re-check slide engagement and appliance leveling

This oven door hinge restores smooth, controlled door movement so the door closes flush and seals properly. Replace a fatigued or bent hinge to reduce heat loss, improve safety, and keep cooking temperatures consistent.

• Supports and pivots the oven door while managing spring tension for controlled opening/closing
• Helps the door gasket compress fully for proper heat retention
• Replaces a hinge that is bent, worn, broken, sticking, or squeaking
• Common symptoms: door won't close fully, drops too quickly, won't hold at a partially open position, misaligned door

• Disconnect electrical power; shut off gas supply if applicable. Allow the appliance to cool completely.
• The hinge is spring-loaded—support the door and use hand/eye protection.
• Remove the door per service procedure, replace the hinge, and ensure the hinge arm seats fully in its receiver before reinstalling the door.
• If the door remains misaligned, inspect the opposing hinge and hinge receivers for wear or damage.

This replacement part is a black element mounting clip used in ranges or wall ovens. This clip is used for surface elements on electric ranges and ovens. The clip itself connects the surface of the element to the support bracket which allows the stove to heat up. The user might need a new clip or clips if the heating element on the stove is loose, if the heating element is completely detached, or if the clip itself is bent or broken. This clip is black and made of sturdy metal that can withstand heat as well as strain on the clip itself. Installation of this clip is very simple as it just requires replacing the old one with a new one and making sure it is secure. Pliers might be required if the old clip is bent or stuck near or on the heating element. There are no special tools needed for this repair. This is an OEM part sourced directly from the manufacturer. It is sold individually. This part is compatible with machines from Frigidaire and other brands like Electrolux, Gibson, Kelvinator, Crosley, Westinghouse, and more.

Size: 8-32t x 0.500 inch. Color: Black.

This clock mounting bracket secures the appliance's clock/timer or electronic oven control behind the control panel. It helps keep the display and keypad aligned and stable so the control stays firmly in place.

• Holds the clock/timer or electronic oven control securely to the console
• Maintains proper alignment of the display and keypad with the front bezel
• Replaces a bent, cracked, or missing bracket
• Typical symptoms include a loose or sagging control, rattling in the console, or a misaligned display/keypad

• Disconnect power at the breaker or unplug the appliance before servicing
• Access the console/backguard and remove the rear cover to reach the control and bracket
• Support the control while removing fasteners; transfer it to the new bracket and reuse original hardware as applicable
• Use ESD precautions when handling the electronic control and avoid overtightening screws

This clear glass shelf provides a sturdy, easy-to-clean storage surface for your refrigerator, helping keep food organized and visible. It restores usable shelving space when an original shelf is cracked, chipped, or missing. What it does:

• Supports food containers, plates and small appliances so items stay organized and level.
• Prevents spills and crumbs from falling to lower compartments; makes clean-up quicker.
• Replaces cracked, chipped or broken shelves that can cause items to shift or fall.
• Restores a proper storage surface when the original interior shelf is damaged or removed.

• Remove food and any loose items from the shelf area before replacing the glass.
• Handle with care and wear cut-resistant gloves; support the glass from underneath while sliding into place.
• Inspect shelf supports or rails for damage and position the glass evenly on the supports; do not force the shelf into misaligned rails.
• Refer to your appliance's owner manual or service guide for model-specific placement instructions.

This oven door latch assembly locks the door during self-clean and reports lock status to the control. Restores proper door locking and unlocking so bake and clean cycles can run safely and without interruptions. What it does:

• Secures the oven door during self-clean and when commanded by the control
• Provides locked/unlocked position feedback to the electronic control
• Helps resolve issues such as a door that won't lock or unlock
• Can address self-clean cycles that won't start or complete and lock-related error messages

• 1 latch assembly

• Disconnect power at the breaker and allow the oven to cool completely
• Access varies by model; you may need to pull the unit and remove the rear or top/control panel
• Photograph wire connections and linkage before removal; transfer any mounting hardware from the original
• After installation, test the lock operation before final reassembly

This oven light lens retainer secures the glass light cover to the oven cavity so the bulb area stays protected during cooking. Replacing a damaged or missing retainer keeps the lens firmly in place and prevents nuisance loosening.

• Holds the glass light lens securely inside the oven cavity
• Helps shield the bulb area from splatters and debris
• Direct replacement for a bent, warped, or missing retainer ring
• Common symptoms: lens won't stay in, cover rattles, or difficulty securing the lens after service

• Disconnect power at the breaker and allow the oven to cool completely
• Remove oven racks for easier access to the light cover area
• Support the glass lens while positioning the retainer to avoid drops or chipping
• Secure the retainer per your model's design; do not overtighten

This small replacement spacer positions and secures appliance components to maintain correct alignment and fit. Installing the spacer restores proper panel spacing and reduces vibration where a worn or missing spacer causes looseness or rubbing. What it does:

• Maintains the correct gap between panels, trim, or assemblies to ensure parts fit flush
• Keeps components aligned to prevent rubbing, binding, or uneven wear
• Helps reduce vibration and rattling caused by a missing or damaged spacer
• Preserves original part spacing for reliable operation of the surrounding components

• Disconnect power to the appliance before any service to avoid shock or injury
• Remove any trim or fasteners that block access; keep track of screws and small parts
• Match the new spacer's orientation to the original; do not force parts into place

This is the stainless steel oven door handle. It lets you safely open and close the oven door and restores a secure, finished look when the original handle is broken, loose, or missing.

• Provides a sturdy grip to operate the oven door
• Helps ensure the door opens/closes smoothly
• Common failure signs: loose handle, broken end caps/mounts, missing or damaged handle
• Cosmetic refresh for a worn or scratched handle

• Disconnect power and allow the oven to cool completely before servicing
• Remove interior door screws to access the handle mounts
• Support the door glass to prevent stress while removing/installing hardware
• Reuse existing screws and trim/end caps or replace them if worn or damaged

Replacement screw that secures panels, trim and internal components in compatible appliances. Restores proper fit and helps reduce rattling or loose parts when the original fastener is missing, worn, or damaged. What it does:

• Fastens panels, brackets, trim pieces and small component assemblies to the appliance frame
• Helps eliminate noise and vibration caused by loose or missing fasteners
• Replaces stripped, corroded or missing screws to restore secure mounting
• Matches OEM fit when the identical screw is required for proper alignment

• Disconnect power to the appliance before starting any repair
• Use the correct driver size to avoid cam-out or damage to the screw head
• Do not overtighten; overtightening can strip threads or crack plastic parts

This outer housing cover replaces a damaged or missing trim piece to protect internal components and restore the appliance's finished appearance. It fits as the exterior cover piece found on the original unit. What it does:

• Protects internal components from dirt, spills and accidental contact
• Conceals wiring and mounting points for a clean, finished look
• Prevents small items from entering sensitive areas that could cause faults
• Restores appearance after panel damage or wear

• One outer housing cover

• Disconnect power to the appliance before starting any service
• Follow the manufacturer's service instructions and keep track of fasteners
• Use basic hand tools; avoid flexing the part to prevent cracking

This foam cabinet insulation panel helps reduce heat transfer and stabilizes internal temperatures, improving cooling performance and efficiency in the refrigerator cabinet. It replaces torn or missing insulation to help maintain consistent operation. What it does:

• Replaces damaged or missing cabinet foam insulation to reduce temperature fluctuations
• Helps limit frost buildup and uneven cooling caused by gaps in the cabinet
• Supports overall refrigerator efficiency by reducing heat gain from surrounding air
• Covers interior cabinet cavities where insulation is required for proper operation

• One foam cabinet insulation panel

• Disconnect power to the appliance before starting any repair
• Remove shelves and access panels for a clear work area; adhesive or clips may secure the insulation
• Press insulation into place, replacing any fasteners or adhesive strips as needed

This electrical receptacle is the small connector that secures a wiring plug to an appliance component, restoring a reliable electrical connection and preventing intermittent operation or arcing. What it does:

• Provides a secure plug-in connection between a wire harness and a component
• Restores power to a component when the original connector is cracked, melted, or corroded
• Helps prevent loose connections that can cause intermittent operation or sparks
• Fits the OEM-style wiring configuration for a direct replacement

• Disconnect power to the appliance before starting any repair
• Remove the damaged connector and match the replacement to the harness before installing
• Use basic hand tools; avoid forcing terminals to prevent damage