Bosch Shx7pt55uc/01 Parts

The Cover Sheet is an OEM part for Bosch dishwashers. It serves as a protective cover for the kickplate area, safeguarding it from dirt, dust, and potential damage.

A bad cover sheet can occur due to wear and tear, accidental damage, or exposure to moisture. Signs of a faulty cover sheet include visible scratches, cracks, or discoloration.

Symptoms of a bad cover sheet include:

• Visible scratches or cracks 
• Discoloration or fading 
• A loose or ill-fitting cover sheet

Replace your damaged or worn-out cover sheet with this genuine OEM Bosch part to restore your dishwasher. This Bosch part can also be used on Thermador and Gaggenau appliances.
 

This temperature sensor (NTC) monitors wash temperature and reports it to the control so the cycle heats and advances correctly. Replacing a faulty sensor can restore proper cleaning performance and normal cycle times. What it does:

• Measures water temperature and sends resistance changes (NTC) to the control
• Helps the control regulate heating and cycle progression
• Failure symptoms can include no/insufficient heat, extended cycles, or poor drying
• May trigger a temperature-sensor fault (e.g., E11 on some models)

• 1 temperature sensor

• Disconnect power and turn off water supply before servicing
• Access is typically at the sump/heat-pump area; remove the toe-kick/lower panel as needed
• Expect some residual water; place a towel or tray to catch drips
• Ensure the sensor seats fully and the seal is in good condition to prevent leaks

The Spray Head is an OEM replacement part for Bosch dishwashers. It directs pressurized water along the dish racks, targeting every inch of dishware and cookware. Consistent coverage cleans thoroughly without waste.   

Symptoms of a bad spray head can include clogged nozzles, inconsistent patterns, or spray heads that do not oscillate and rotate properly through cycles. Mineral deposits pose blockage risks over time.

Causes of a bad spray head include:

• Uneven or skipped areas of spray coverage inside the machine
• Rotating/oscillating mechanisms that jam or continuously stick  
• Nozzles fully or partially blocked reducing water pressure
• Head assembly detaching from water tub wall or bracket

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This repair set renews the hinge pivot components so the door opens smoothly and closes squarely. Replacing the worn hardware helps maintain proper alignment and a tight gasket seal for consistent performance. What it does:

• Replaces worn hinge pin/bushing hardware to restore door support
• Helps fix a door that sags, scrapes, or won't close flush
• Can reduce clicking, squeaking, or grinding at the hinge
• Helps the door seal make full contact to prevent warm air leaks

• 1 repair set

• Disconnect power; if applicable, turn off the water supply
• Remove items from the door; support the door and lift it off the hinge
• Install the new hinge hardware in the original orientation
• Reinstall and align the door; verify gasket seal and adjust leveling if needed

This factory screw secures select Bosch/BSH appliance components. Use it to replace a missing or damaged fastener so panels, brackets, or trim stay tight and rattle-free during operation.

• Tightens and holds appliance parts such as panels, brackets, or trim in place
• Helps correct issues like loose or vibrating panels caused by a missing/stripped screw
• Maintains proper fitment after service or disassembly
• Torx T20 drive head helps resist cam-out during tightening

• Unplug power and shut off any water supply before servicing
• Use a T20 Torx driver; hand-start to avoid cross-threading
• Do not overtighten—snug to manufacturer torque guidance if available
• Replace any additional missing or damaged fasteners for even clamping

This factory fastener secures panels, brackets, and internal components in your appliance. Replacing a missing or damaged screw restores a snug fit, reduces vibration and rattles, and keeps assemblies properly aligned during service or reassembly.

• Anchors panels, trim, and internal parts to the appliance frame or subassemblies
• Helps prevent vibration, buzzing, and loose or shifting components
• Ideal replacement for lost, stripped, or corroded hardware
• Common symptoms include loose panels, gaps, rattling noises, or parts that won't stay secured

• Disconnect power and shut off water or gas before servicing
• Match this screw to the original and replace one-for-one in the same location
• Start threads by hand to avoid cross-threading; use the correct driver and do not overtighten
• Inspect the mating clip/insert; replace if stripped or damaged for a secure hold

This electronic program control manages the appliance's cycle selection and timing so your unit runs the correct program and sequencing. Replacing a faulty module restores programmed functions and command-response from the control panel. What it does:

• Controls program selection, cycle timing and sequence execution
• Sends and receives signals to sensors, valves and motors for proper operation
• Stops or advances cycles based on programmed logic
• Common symptoms: unresponsive controls, cycles won't start or complete, intermittent operation, or error codes related to the control board

• Disconnect power at the breaker or unplug the appliance before starting
• Handle the module carefully to avoid ESD damage; avoid touching circuit components
• Verify connectors are fully seated and mounting is secure before restoring power
• Test basic functions and a full cycle after installation to confirm correct operation

This holder secures internal components to keep assemblies aligned and stable, reducing vibration and wear. It's a simple replacement that restores proper fit where a broken or missing clip causes loose panels or noisy operation. What it does

• Secures and aligns panels or wiring harnesses inside the appliance
• Prevents rattling, vibration, and misalignment caused by damaged or missing clips
• Helps maintain proper component spacing to avoid wear or interference
• Restores secure attachment after breakage or plastic fatigue

• Disconnect power and water before starting any repair
• Remove access panels or trim to reach the damaged clip—keep fasteners organized
• Press or snap the holder into place; replace any broken tabs before reassembling
• If plastic anchors are damaged, replace them with matching OEM clips

This replacement worm gear is a small plastic drive gear that transmits rotational motion between the motor and driven components, restoring normal gear-driven movement and reducing slipping or grinding. What it does:

• Transfers torque from the motor to the mating gear or gearbox for proper mechanical operation
• Replaces worn, stripped, or damaged worm teeth that cause slipping or loss of drive
• Stops grinding, clicking, or intermittent movement when the gear is the fault
• Helps restore smooth, consistent operation of the driven mechanism when installed correctly

• One worm gear

• Disconnect power to the appliance before beginning any repair
• Inspect mating gears and shafts for wear; replace worn parts to prevent repeat failure
• Use OEM-approved lubricant only where specified; do not force or overtighten mating components

This sealing is a molded rubber gasket that provides a watertight barrier where two appliance components meet, helping prevent leaks and water damage. It's a direct-fit replacement when the original seal is cracked or worn. What it does:

• Creates a watertight seal to help prevent leaks during operation
• Restores proper sealing where the original gasket has become brittle, torn, or flattened
• Helps maintain appliance performance by keeping water inside the wash/tub area
• Reduces risk of water damage to cabinetry or floors from failing seals

• One sealing

• Disconnect power and water supply before beginning any repair
• Verify mating surfaces are clean and dry; remove any old sealant or debris for a proper fit
• Inspect the replacement for damage before installing and align evenly to avoid pinching

The Thread Bolt is an OEM part for Bosch dishwashers. It serves as a fastening component, securing the water inlet in place and ensuring a proper water supply connection.

Causes of a malfunctioning Thread Bolt can include cross-threading or over-tightening during installation, leading to stripping or damage.  

Symptoms of a bad Thread Bolt include:

• Leaks around the water inlet area Loose or rattling water inlet valve 
• Difficulty in accessing or removing the valve assembly 

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Funnel is an OEM part for Bosch dishwashers. It helps accurately guide water from the inlet valve onto wash arms and other components inside the dishwasher.

As water flows through the funnel during each cycle, small debris particles can become trapped. Over time, a buildup of mineral deposits or grime occurs inside the funnel.

Causes are normal mineral accumulation from hard water, along with food particles or grit trapped during dishwasher use.

Symptoms of a bad funnel include:

• Reduced or uneven water pressure to spray arms
• Clogs or blockages that hamper water flow
• Mineral deposits visible inside the funnel

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This water softener assembly conditions incoming dishwasher water to reduce mineral buildup and improve wash performance. It helps prevent hard-water spots and cloudy glassware for clearer, cleaner results. What it does:

• Removes or binds hardness minerals from incoming water to reduce limescale and spotting
• Helps maintain detergent effectiveness for better cleaning and rinsing
• Reduces mineral buildup inside the wash system and on dishes and glassware
• Supports consistent wash performance in areas with hard water

• One water softener assembly

• Disconnect power and shut off the water supply before servicing
• Inspect and replace any seals or gaskets if damaged; use manufacturer-recommended parts
• Handle the unit carefully to avoid damage to connectors or mounting features
• Refer to the dishwasher service manual or OEM installation instructions for exact placement and wiring

This temperature sensor (thermistor) measures appliance temperature and sends a signal to the control board so the unit can maintain proper cooling cycles. Replaces a failed or intermittent sensor for more reliable temperature control. What it does:

• Detects internal temperature and provides a changing resistance signal to the control board
• Helps the control board regulate compressor and fan operation for consistent cooling
• Commonly linked to symptoms like incorrect temperatures, frequent cycling, or related error codes
• Works as a direct-replacement sensing element

• One temperature sensor (thermistor) as pictured

• Disconnect power before servicing to avoid shock or damage
• Handle the sensor and wiring gently; avoid kinking or pinching the harness
• Access may require removing interior panels or covers; keep mounting hardware for reinstallation
• Test with a multimeter or follow OEM service instructions before replacement