Cfef388ces-3 Parts

This lower drawer replaces a damaged or missing bottom drawer on your range, restoring smooth slide action and a flush, finished look so the lower compartment operates correctly and the appliance is complete again.

• Forms the pull-out compartment beneath the oven for convenient access
• Interfaces with the drawer slides to open and close smoothly
• Restores proper alignment and full closure at the base of the range
• Typical symptoms: drawer jams, falls off tracks, sits unevenly, or is bent/dented

• Disconnect power and shut off gas; allow the range to cool before servicing
• Pull the old drawer out and lift to disengage from the slides; transfer any reusable parts as needed
• Set the new drawer onto both slides evenly and test for smooth travel and full closure
• If the drawer doesn't seat flush, re-check slide engagement and appliance leveling

This oven door hinge restores smooth, controlled door movement so the door closes flush and seals properly. Replace a fatigued or bent hinge to reduce heat loss, improve safety, and keep cooking temperatures consistent.

• Supports and pivots the oven door while managing spring tension for controlled opening/closing
• Helps the door gasket compress fully for proper heat retention
• Replaces a hinge that is bent, worn, broken, sticking, or squeaking
• Common symptoms: door won't close fully, drops too quickly, won't hold at a partially open position, misaligned door

• Disconnect electrical power; shut off gas supply if applicable. Allow the appliance to cool completely.
• The hinge is spring-loaded—support the door and use hand/eye protection.
• Remove the door per service procedure, replace the hinge, and ensure the hinge arm seats fully in its receiver before reinstalling the door.
• If the door remains misaligned, inspect the opposing hinge and hinge receivers for wear or damage.

The Range Glass Assembly is an OEM part for Frigidaire ranges. It covers the inner cooking cavity, protecting both the occupant and the heating elements and mechanisms inside. The glass assembly also allows for viewing into the oven to check on food without needing to open the door each time. 

Symptoms of a bad glass assembly include:

• Cracks or breaks in the glass
• Difficulty viewing into the oven cavity 
• Leaks around the glass seal
• The glass popping out of place

Causes of a bad glass assembly can be wear and tear over time, exposure to excessive heat, or damage from impacts. 

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement part is a black element mounting clip used in ranges or wall ovens. This clip is used for surface elements on electric ranges and ovens. The clip itself connects the surface of the element to the support bracket which allows the stove to heat up. The user might need a new clip or clips if the heating element on the stove is loose, if the heating element is completely detached, or if the clip itself is bent or broken. This clip is black and made of sturdy metal that can withstand heat as well as strain on the clip itself. Installation of this clip is very simple as it just requires replacing the old one with a new one and making sure it is secure. Pliers might be required if the old clip is bent or stuck near or on the heating element. There are no special tools needed for this repair. This is an OEM part sourced directly from the manufacturer. It is sold individually. This part is compatible with machines from Frigidaire and other brands like Electrolux, Gibson, Kelvinator, Crosley, Westinghouse, and more.

This burner cap sits on top of the sealed burner head on a gas cooktop/range to evenly distribute flame and protect the burner from spills. Replacing a damaged or missing cap helps restore proper flame pattern and efficient cooking performance.

• Covers the burner head to shape the flame and shield it from debris
• Helps ensure even heating across cookware
• Common signs it may need replacement: uneven or yellow flames, sputtering or noisy burner, cookware scorching on one side, cap chipped, warped, or missing
• Color/finish: black

• Shut off gas supply and allow the cooktop to cool completely before servicing
• Lift off the old cap; clean the burner head surface
• Center the new cap on the burner head—ensure it seats flat and stable
• Test the burner for a steady, even blue flame after reassembly

250V.

Size: 8-32t x 0.500 inch. Color: Black.

These chrome drip bowls sit beneath coil surface elements to catch spills and reflect heat. Sized for 8-inch and 6-inch burners, they refresh the cooktop's appearance and help elements seat correctly. What it does:

• Collects drips and splatters under coil elements and reflects heat back toward cookware
• Restores a clean look when originals are stained, pitted, or rusted
• Helps burners sit level and make solid contact with the cooktop
• Common signs to replace: heavy discoloration, rust, broken tabs, warping, lingering smoke or odor from burnt-on spills

• Two chrome drip bowls: one 8-inch and one 6-inch

• Disconnect power at the breaker and allow surface units to cool completely
• Pull the coil element straight out of its receptacle, then lift out the old bowl
• Align the new bowl's notches with the cooktop opening and seat it flat
• Reinsert the element fully and ensure it rests evenly in the bowl

This clock mounting bracket secures the appliance's clock/timer or electronic oven control behind the control panel. It helps keep the display and keypad aligned and stable so the control stays firmly in place.

• Holds the clock/timer or electronic oven control securely to the console
• Maintains proper alignment of the display and keypad with the front bezel
• Replaces a bent, cracked, or missing bracket
• Typical symptoms include a loose or sagging control, rattling in the console, or a misaligned display/keypad

• Disconnect power at the breaker or unplug the appliance before servicing
• Access the console/backguard and remove the rear cover to reach the control and bracket
• Support the control while removing fasteners; transfer it to the new bracket and reuse original hardware as applicable
• Use ESD precautions when handling the electronic control and avoid overtightening screws

This oven door hinge connects the door to the appliance frame and controls its movement. Replacing a worn hinge restores smooth, controlled operation and a proper seal to help keep heat in and cooking performance consistent. What it does:

• Supports and guides the oven door as it opens and closes
• Spring mechanism helps the door stay closed and hold at partial-open positions
• Maintains door alignment with the gasket to reduce heat loss
• Typical symptoms: door won't close fully, drops open quickly, sits uneven, or needs extra force to latch

• One hinge

• Disconnect power; turn off gas supply for gas models
• Remove the door per your owner's manual; engage hinge locks or insert hinge pins before lifting the door
• Support the door and watch for sharp edges and spring tension; wear gloves and eye protection
• Many ovens use two hinges—inspect both and replace in pairs if wear is uneven

The Outer Door Glass is an OEM part for Frigidaire ranges. It forms the transparent viewing window on the front exterior of the oven door.

The outer glass allows homeowners to efficiently monitor food items while baking or roasting. Its multi-pane design works to insulate retained heat within the oven cavity, maintaining set temperatures for optimal cooking results.

Over time, causes like impacts or abrasions from cleaning can damage the outer door glass surface or compromise its seal.

Symptoms of a failing outer door glass include:

• Visible cracks or scratches reducing visibility inside the oven
• Air gaps forming between the glass panes allowing heat to escape
• Fogging or condensation building up between panes

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Replacement wiring harness that connects control electronics to internal components, restoring proper electrical connections and reliable operation. Use when factory wiring is damaged, loose, or causing intermittent component failures. What it does:

• Routes power and signal between the appliance control board and internal components.
• Restores continuity when broken, frayed, or corroded wires cause intermittent or no operation.
• Can resolve symptoms such as non-responsive controls, lights or fans not running, or intermittent component operation.
• Keeps wiring neat and secured along original routing to prevent rubbing and stress.

• Always disconnect power (unplug or shut off breaker) before starting any repair.
• Match connector shapes and pin counts; route harness along original clips and pathways to avoid pinch points.
• Inspect mating connectors and terminals for damage or corrosion before reconnecting.

This clear glass shelf provides a sturdy, easy-to-clean storage surface for your refrigerator, helping keep food organized and visible. It restores usable shelving space when an original shelf is cracked, chipped, or missing. What it does:

• Supports food containers, plates and small appliances so items stay organized and level.
• Prevents spills and crumbs from falling to lower compartments; makes clean-up quicker.
• Replaces cracked, chipped or broken shelves that can cause items to shift or fall.
• Restores a proper storage surface when the original interior shelf is damaged or removed.

• Remove food and any loose items from the shelf area before replacing the glass.
• Handle with care and wear cut-resistant gloves; support the glass from underneath while sliding into place.
• Inspect shelf supports or rails for damage and position the glass evenly on the supports; do not force the shelf into misaligned rails.
• Refer to your appliance's owner manual or service guide for model-specific placement instructions.

This oven door latch assembly locks the door during self-clean and reports lock status to the control. Restores proper door locking and unlocking so bake and clean cycles can run safely and without interruptions. What it does:

• Secures the oven door during self-clean and when commanded by the control
• Provides locked/unlocked position feedback to the electronic control
• Helps resolve issues such as a door that won't lock or unlock
• Can address self-clean cycles that won't start or complete and lock-related error messages

• 1 latch assembly

• Disconnect power at the breaker and allow the oven to cool completely
• Access varies by model; you may need to pull the unit and remove the rear or top/control panel
• Photograph wire connections and linkage before removal; transfer any mounting hardware from the original
• After installation, test the lock operation before final reassembly

Color: Black

The Knob is an OEM part for Frigidaire ranges. The knob attaches directly to the surface element switch and allows for easy adjustment of settings with a simple turn.

Causes of a bad range knob can be normal wear and tear over time, exposing the knob to excessive heat, or accidental damage from impact.

Symptoms of a bad range knob include:

• Loose, wobbly or difficult to turn fitment
• Cracked, broken or missing pieces
• Control functions that do not work as intended
• Inaccurate temperature readings
• Knob that falls off or does not stay securely attached

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Support for broil heating element.