Cye22tshhgss Parts

This ice maker feeler arm senses the ice level in the bin and controls when the icemaker starts and stops. Replacing a bent, missing, or stuck arm restores correct shutoff and helps prevent overfilling or no-ice conditions.

• Monitors the ice bucket level and raises/lowers to start or stop ice production
• Shuts the icemaker off when the bin is full; allows production when lowered
• Common symptoms: ice maker won't stop making ice/overflows, no ice when the arm is stuck up, loose or missing arm
• Restores proper on/off control of the icemaker cycle

• Disconnect power and turn off the water supply before servicing
• Remove the ice bin and, the icemaker assembly to access the arm
• Transfer any reusable hardware; seat the arm fully in its pivot points so it moves freely
• Restore power, lower the arm to the On position, and allow time for the icemaker to cycle

8-18 CA HX 1/2 S

This felt tape is used in the refrigerator to cushion and seal mating parts, helping reduce vibration/squeaks and prevent chafing or small air leaks. Replace worn or missing tape to restore a quieter, more secure fit of covers and ducts.

• Provides a soft barrier between panels, ducts, or rails to minimize vibration and squeaks
• Helps seal minor gaps to support proper airflow paths
• Replaces deteriorated, compressed, or missing original felt tape
• Common symptoms include rattling/buzzing from covers or panels, squeaking drawers, or a loose cover that won't seat correctly

• Disconnect power to the refrigerator before servicing
• Note the original tape's location; remove the old tape and any residue
• Clean and dry surfaces thoroughly; apply the new tape in the same position (peel liner if adhesive-backed)
• Do not block vents, sensors, or fastener holes when applying

This hinge-mounted refrigerator door stop limits how far the door swings open, protecting the cabinet and nearby walls from impact. Replace a cracked or missing stop to restore a controlled, factory door swing and prevent overextension.

• Mounts on the door hinge to control the door's opening range
• Helps prevent the door or handle from striking adjacent walls or cabinets
• Common symptoms: door opens past its normal range, broken/missing stop, visible wear at the hinge stop
• Often needed after an impact or when the original stop cracks from fatigue

• Disconnect power; turn off water to the door if applicable
• Support the door before loosening hinge fasteners; door removal may be required on some models
• Install the stop on the correct hinge location (right or left as required) and tighten hardware securely
• Verify door swing and clearance before fully loading shelves

This water filter cover assembly secures the refrigerator's water filter cartridge and helps direct filtered water into the dispenser/ice system, restoring proper filter seating and reducing the risk of leaks or poor water flow. What it does:

• Secures and retains the water filter cartridge in its housing
• Seals the filter area to help prevent water leaks around the filter
• Directs filtered water from the cartridge into the dispenser and ice system
• Helps restore proper filter engagement when the original cover is cracked or broken

• Turn off water supply and remove power to the appliance before servicing
• Remove the old cover and verify filter type/orientation before installing the new cover
• Push the cover into place until the filter seats and locks per the appliance design
• Re-check alignment and seals; replace damaged gaskets as needed

This replacement basket bottom assembly restores the lower basket's support and containment so stored items sit securely and the basket functions as intended. It's a direct-replacement part used when the basket floor is cracked, warped, or broken. What it does:

• Replaces the lower/bottom section of the basket to restore proper support and prevent items from falling through
• Stabilizes the basket so it rolls and seats correctly
• Stops rattling or sagging caused by a damaged or missing basket bottom
• Useful when the basket floor is cracked, split, or has broken support ribs

• Disconnect power to the appliance before any service; follow the manufacturer's safety instructions
• Remove the basket or access panel as needed to reach and replace the bottom assembly
• Inspect surrounding mounting tabs and rails for damage; replace any worn hardware for a secure fit
• Use basic hand tools.

The Door Board is an OEM component designed for GE bottom-mount refrigerators. Located inside refrigerator doors, it operates essential LED functions for interior lighting and temperature displays. Properly illuminated shelves and accurate temperature readings depend on a functioning door board.

Causes of failure can include loose wiring connections from repeated door openings, fluid damage allowing corrosion over time, or failure of electronic components on the printed circuit board.

Symptoms of a defective door board are:

• Dim or unlit interior lighting 
• Inoperative temperature display
• Strange odor or sparks coming from the door area

Replacing with this genuine GE part restores bright illumination and easy temperature monitoring. Compatible with Hotpoint, RCA, and Kenmore side-by-side models as well.

A #8-18 x 9/16-inch hex washer head screw used to secure panels and components in appliances. Provides a proper fit for fast, reliable fastening when replacing missing, damaged, or stripped screws. What it does:

• Secures panels, brackets, and trim to keep components aligned and stable.
• Restores proper fastening when threads are stripped, the original screw is missing, or a head is damaged.
• Helps stop rattling or loose parts caused by worn or broken fasteners.
• Fits applications requiring a #8-18 thread with a 9/16" length and hex washer head style.

• Verify thread size, head style, and length before installation.
• Use the correct hex driver or socket to avoid cam-out or head damage.
• Do not overtighten; snug until secure to avoid stripping threads or deforming parts.
• Disconnect power and follow appliance-specific safety steps.

This port collar is a small trim/support piece used on select refrigerators. It reinforces the port opening and helps secure the mating tube or component for proper alignment, a snug fit, and a clean, finished appearance.

• Supports and spaces the port/opening where a tube or component passes through the cabinet or liner
• Helps maintain alignment and a secure fit to minimize gaps or vibration
• Replace if the collar is cracked, warped, or missing
• Symptoms can include a loose connection at the opening, rattling, or a visible gap or misalignment

• Unplug the refrigerator; shut off the water supply if working near water lines
• Use your model's parts diagram to access the port; remove any trim, clips, or screws
• Note orientation; press or snap the new collar into place and transfer any seals if present
• Reassemble and restore power; verify proper fit and operation

This paddle front switch assembly replaces a worn or failed dispenser paddle so the dispenser responds reliably when pressed. It restores user control for water or ice dispensing on compatible refrigerators. What it does:

• Activates the dispenser control when you press the front paddle
• Replaces a cracked, loose, or non-responsive paddle that won't trigger dispensing
• Stops intermittent or no-response dispenser behavior caused by a faulty switch
• Restores proper tactile feel and electrical engagement for dispenser operation

• One paddle front switch assembly

• Disconnect refrigerator power (and water supply if needed) before starting
• Remove dispenser bezel or front trim to access the switch; handle the paddle carefully
• Verify electrical connector seating and secure mounting during reassembly

Manufactured by GE, this is a compressor kit for a refrigerator. The compressor's job is to pressurize the system and warm the refrigerant while propelling it through the rest of the cooling system. The compressor is controlled by a thermostat inside the refrigerator. When the thermostat detects a high temperature, the compressor engages, helping to cool the refrigerator and preserve food.Compressors are the core of the refrigeration system. There are also subject to a great deal of wear and tear through normal cycling on and off. In addition, compressors can be damaged if they run out of oil, if contaminants enter the system, and through exposure to prolonged operation due to a faulty thermostat or low refrigerant levels. When the compressor fails, the refrigerator will no longer be able to maintain a safe temperature for food. This is a complete replacement kit.This kit is a genuine OEM part and is sold individually. It is only compatible with GE refrigerators.

8-18 hi/lo 5/8

This 8-18 x 9/16 screw is a short sheet-metal fastener used to secure panels, trim and small components on appliances. It replaces missing or stripped screws to restore proper fit and reduce noise from loose parts. What it does

• Secures appliance panels, brackets and trim to prevent movement and rattling
• Holds small components in correct alignment for reliable operation
• Replaces lost, worn or stripped screws that cause gaps or loose fittings
• Common symptom link: fixes rattling panels, loose trim, or parts that shift during use

• One 8-18 x 9/16 screw

• Use the correct 8-18 driver bit and hand or low-torque power driver to avoid stripping
• Do not overtighten; snug until secure to prevent thread damage or panel deformation
• Turn power off/unplug appliance when installing near electrical components
• Keep extra screws on hand—hardware often comes in single quantities

This element holder assembly secures an oven/range heating element and keeps it positioned for even heat delivery. It restores proper element alignment to reduce arcing and prevent rubbing or uneven baking. What it does:

• Secures the bake or broil heating element to the range/oven housing
• Keeps the element properly spaced for consistent heating performance
• Helps stop element movement, rubbing, or intermittent contact that can cause arcing
• Commonly replaced when the element is loose, misaligned, or makes noise during operation

• Disconnect power to the appliance before beginning any repair
• Handle heating elements carefully—sharp edges and fragile terminals can be damaged
• Verify element alignment and secure mounting hardware; replace only as needed
• If you see damaged element terminals or insulation, replace the element

Replacement mat module that restores mat-sensing and control functions in compatible appliances. Installs in the mat/sensor assembly to help the appliance detect mat input and respond correctly. What it does:

• Interprets signals from the mat/sensor assembly and communicates those signals to the appliance control system.
• Replaces a damaged or failed module that can cause unresponsive mat inputs or intermittent mat-related operation.
• Helps resolve mat/sensor error codes or persistent mat-detection faults when the module is the failed component.

• Disconnect power to the appliance before servicing to avoid electrical shock.
• Handle the module carefully and avoid touching circuitry or connector pins to prevent damage from ESD or contamination.

This holder element assembly secures the appliance's heating element in the correct position so the element stays stable for consistent operation and safe performance. It's a direct-fit replacement for worn or damaged holders. What it does:

• Secures and supports the heating element inside the appliance to maintain proper alignment
• Prevents element sagging or contact with other components that can cause noise or arcing
• Helps reduce vibration and movement that can lead to intermittent heating
• Common symptom: visible holder damage, loose or shifted element, unusual noise during operation

• Disconnect power (unplug or switch off breaker) before starting any repair
• Allow appliance and element to fully cool before handling
• Handle the element and holder carefully to avoid bending or damaging the element