Cye23tsdss Parts

This felt tape is used in the refrigerator to cushion and seal mating parts, helping reduce vibration/squeaks and prevent chafing or small air leaks. Replace worn or missing tape to restore a quieter, more secure fit of covers and ducts.

• Provides a soft barrier between panels, ducts, or rails to minimize vibration and squeaks
• Helps seal minor gaps to support proper airflow paths
• Replaces deteriorated, compressed, or missing original felt tape
• Common symptoms include rattling/buzzing from covers or panels, squeaking drawers, or a loose cover that won't seat correctly

• Disconnect power to the refrigerator before servicing
• Note the original tape's location; remove the old tape and any residue
• Clean and dry surfaces thoroughly; apply the new tape in the same position (peel liner if adhesive-backed)
• Do not block vents, sensors, or fastener holes when applying

This hinge-mounted refrigerator door stop limits how far the door swings open, protecting the cabinet and nearby walls from impact. Replace a cracked or missing stop to restore a controlled, factory door swing and prevent overextension.

• Mounts on the door hinge to control the door's opening range
• Helps prevent the door or handle from striking adjacent walls or cabinets
• Common symptoms: door opens past its normal range, broken/missing stop, visible wear at the hinge stop
• Often needed after an impact or when the original stop cracks from fatigue

• Disconnect power; turn off water to the door if applicable
• Support the door before loosening hinge fasteners; door removal may be required on some models
• Install the stop on the correct hinge location (right or left as required) and tighten hardware securely
• Verify door swing and clearance before fully loading shelves

This evaporator cover is the molded housing that protects the freezer evaporator and helps direct airflow for proper defrosting and cooling performance. It replaces a damaged or cracked cover to restore proper airflow management. What it does:

• Shields the evaporator coil and fan area from debris and direct contact
• Helps direct airflow through the evaporator for even cooling
• Supports proper defrost drainage and reduces ice buildup when functioning correctly
• Can reduce unusual noises caused by loose or broken cover components

• Requires access to the freezer interior and removal of shelves/panels; follow manufacturer service manual for disassembly steps
• Power off and unplug appliance before starting work and allow any accumulated frost to thaw safely
• Inspect associated gaskets, fasteners, and the evaporator fan while replacing the cover; replace any damaged parts as needed

This replacement basket bottom assembly restores the lower basket's support and containment so stored items sit securely and the basket functions as intended. It's a direct-replacement part used when the basket floor is cracked, warped, or broken. What it does:

• Replaces the lower/bottom section of the basket to restore proper support and prevent items from falling through
• Stabilizes the basket so it rolls and seats correctly
• Stops rattling or sagging caused by a damaged or missing basket bottom
• Useful when the basket floor is cracked, split, or has broken support ribs

• Disconnect power to the appliance before any service; follow the manufacturer's safety instructions
• Remove the basket or access panel as needed to reach and replace the bottom assembly
• Inspect surrounding mounting tabs and rails for damage; replace any worn hardware for a secure fit
• Use basic hand tools.

The Door Board is an OEM component designed for GE bottom-mount refrigerators. Located inside refrigerator doors, it operates essential LED functions for interior lighting and temperature displays. Properly illuminated shelves and accurate temperature readings depend on a functioning door board.

Causes of failure can include loose wiring connections from repeated door openings, fluid damage allowing corrosion over time, or failure of electronic components on the printed circuit board.

Symptoms of a defective door board are:

• Dim or unlit interior lighting 
• Inoperative temperature display
• Strange odor or sparks coming from the door area

Replacing with this genuine GE part restores bright illumination and easy temperature monitoring. Compatible with Hotpoint, RCA, and Kenmore side-by-side models as well.

This replacement odor filter cartridge helps reduce common food and cooking smells inside the refrigerator, keeping stored items fresher-smelling. Designed to fit the factory filter housing and work with compatible GE refrigerator models. What it does

• Absorbs and helps neutralize odors from food, spills and strong-smelling items
• Installs in the refrigerator's filter housing to continuously treat circulating air
• Helps maintain a fresher-smelling interior without altering cooling performance
• Works as part of routine maintenance to address persistent refrigerator odors

• Replace with the refrigerator powered on but follow the manufacturer's handling instructions
• Locate and remove the old cartridge per your model's manual, then insert the new cartridge until it seats
• Dispose of the used cartridge according to local regulations
• If odors persist after replacement, check for spoiled food, spills, or water filter issues

A #8-18 x 9/16-inch hex washer head screw used to secure panels and components in appliances. Provides a proper fit for fast, reliable fastening when replacing missing, damaged, or stripped screws. What it does:

• Secures panels, brackets, and trim to keep components aligned and stable.
• Restores proper fastening when threads are stripped, the original screw is missing, or a head is damaged.
• Helps stop rattling or loose parts caused by worn or broken fasteners.
• Fits applications requiring a #8-18 thread with a 9/16" length and hex washer head style.

• Verify thread size, head style, and length before installation.
• Use the correct hex driver or socket to avoid cam-out or head damage.
• Do not overtighten; snug until secure to avoid stripping threads or deforming parts.
• Disconnect power and follow appliance-specific safety steps.

This paddle front switch assembly replaces a worn or failed dispenser paddle so the dispenser responds reliably when pressed. It restores user control for water or ice dispensing on compatible refrigerators. What it does:

• Activates the dispenser control when you press the front paddle
• Replaces a cracked, loose, or non-responsive paddle that won't trigger dispensing
• Stops intermittent or no-response dispenser behavior caused by a faulty switch
• Restores proper tactile feel and electrical engagement for dispenser operation

• One paddle front switch assembly

• Disconnect refrigerator power (and water supply if needed) before starting
• Remove dispenser bezel or front trim to access the switch; handle the paddle carefully
• Verify electrical connector seating and secure mounting during reassembly

8-18 hi/lo 5/8

This 8-18 x 9/16 screw is a short sheet-metal fastener used to secure panels, trim and small components on appliances. It replaces missing or stripped screws to restore proper fit and reduce noise from loose parts. What it does

• Secures appliance panels, brackets and trim to prevent movement and rattling
• Holds small components in correct alignment for reliable operation
• Replaces lost, worn or stripped screws that cause gaps or loose fittings
• Common symptom link: fixes rattling panels, loose trim, or parts that shift during use

• One 8-18 x 9/16 screw

• Use the correct 8-18 driver bit and hand or low-torque power driver to avoid stripping
• Do not overtighten; snug until secure to prevent thread damage or panel deformation
• Turn power off/unplug appliance when installing near electrical components
• Keep extra screws on hand—hardware often comes in single quantities

This silicon controlled rectifier (SCR) is a replacement power-control semiconductor used to regulate current in appliance power circuits, helping restore proper operation of heating and motor circuits that rely on solid-state switching. What it does:

• Acts as a switch to control and modulate electrical current in the appliance power path
• Enables regulated power delivery to heating elements or motor circuits when driven by the control board
• Commonly replaced when the appliance shows intermittent power, no heat, or erratic on/off behavior in the affected circuit
• Works as a direct replacement for the OEM SCR with identical mounting and electrical fit when specified by part number

• Disconnect power to the appliance before starting any repair to avoid shock or damage
• Observe basic ESD precautions when handling the SCR and avoid touching semiconductor leads

This element holder assembly secures an oven/range heating element and keeps it positioned for even heat delivery. It restores proper element alignment to reduce arcing and prevent rubbing or uneven baking. What it does:

• Secures the bake or broil heating element to the range/oven housing
• Keeps the element properly spaced for consistent heating performance
• Helps stop element movement, rubbing, or intermittent contact that can cause arcing
• Commonly replaced when the element is loose, misaligned, or makes noise during operation

• Disconnect power to the appliance before beginning any repair
• Handle heating elements carefully—sharp edges and fragile terminals can be damaged
• Verify element alignment and secure mounting hardware; replace only as needed
• If you see damaged element terminals or insulation, replace the element

Replacement mat module that restores mat-sensing and control functions in compatible appliances. Installs in the mat/sensor assembly to help the appliance detect mat input and respond correctly. What it does:

• Interprets signals from the mat/sensor assembly and communicates those signals to the appliance control system.
• Replaces a damaged or failed module that can cause unresponsive mat inputs or intermittent mat-related operation.
• Helps resolve mat/sensor error codes or persistent mat-detection faults when the module is the failed component.

• Disconnect power to the appliance before servicing to avoid electrical shock.
• Handle the module carefully and avoid touching circuitry or connector pins to prevent damage from ESD or contamination.

The Flow Meter is an OEM replacement part for GE refrigerators. It is designed to monitor and regulate the flow of water into the refrigerator's ice maker and water dispenser, preventing overfilling or insufficient water supply. 

A bad flow meter can occur due to normal wear and tear, clogging or blockage in the water lines, or damage to the flow meter mechanism. If you notice symptoms such as low ice production, slow or weak water flow from the dispenser, or water leakage, it may indicate a need to replace the flow meter.

Symptoms of a bad flow meter include:

• Low ice production
• Slow or weak water flow from the dispenser
• Water leaks

Restore your refrigerator by replacing the faulty flow meter with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This holder element assembly secures the appliance's heating element in the correct position so the element stays stable for consistent operation and safe performance. It's a direct-fit replacement for worn or damaged holders. What it does:

• Secures and supports the heating element inside the appliance to maintain proper alignment
• Prevents element sagging or contact with other components that can cause noise or arcing
• Helps reduce vibration and movement that can lead to intermittent heating
• Common symptom: visible holder damage, loose or shifted element, unusual noise during operation

• Disconnect power (unplug or switch off breaker) before starting any repair
• Allow appliance and element to fully cool before handling
• Handle the element and holder carefully to avoid bending or damaging the element

This tube clamp secures flexible water tubing to its fitting in refrigerators. It helps maintain a tight seal to prevent leaks and keeps lines from slipping off under normal operating pressure.

• Holds plastic or rubber tubing firmly on a barbed fitting or nipple
• Helps prevent drips and leaks at tube connection points
• Addresses loose or disconnected water lines
• Useful when tubing slips off or won't stay seated

• Disconnect power and shut off the water supply before servicing
• Position the clamp over the tube and fitting; compress with pliers and release to lock in place
• Ensure the clamp is centered and fully seated; tug-test the tube
• Restore water and power; check all connections for leaks