Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
The Rear Drum Bearing Kit is an OEM replacement part for GE dryers. It is a comprehensive kit that includes both rear drum bearings and necessary mounting hardware. These bearings play a vital role in smoothly rotating the dryer drum during cycles, reducing vibrations and noise.
Symptoms of bad bearings include:
Causes of bad bearings can include normal wear and tear over time, exposure to excessive loads or unbalanced loads that strained the bearings, or damage from extended use without proper lubrication.
This OEM replacement is also compatible with Hotpoint, RCA, and some Kenmore models.
Repair went well, replaced the pulley wheel, belt, rear drum bearing. Had an issue after replacement with the dryer stopping after ~5mins or so when running with heat. Fluff cycle would run fine. Details: The lock nut on the pulley wheel didn't feel tight enough so i tried to crimp it back on the pulley arm. It then became way too lose. I had to replace it with a plastic washer I had in my toolkit. That fit snug and seems to work fine. I also added some grease to the pulley shaft under... Read more
The Idler Pulley is an OEM part for GE dryers. This critical component helps to maintain the correct tension on the dryer's drive belt, ensuring smooth operation and preventing it from slipping.
Symptoms of a bad Idler Pulley include:
Causes of a bad idler pulley can include worn bearings, accumulation of lint and debris that impedes rotation, or material fatigue after prolonged use.
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
The Dryer Drive Belt is an OEM part for GE dryers that connects the motor to the drum, allowing the drum to rotate during the drying cycle. The belt measures approximately 87 inches long and 0.25 inches wide, with 4 ribs.
Over time, the Dryer Drive Belt can wear out or break, leading to the drum not turning.
Symptoms of a bad Dryer Drive Belt include:
This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.
My GE dryer from the late 80's/early 90's was squealing when it would start up, belt or bearing I was thinking. I found a manual online that covered my model and I watched a video on this site that showed me how to take it all apart, mine was a bit different but the principles were the same. I took it apart and added some quick-disconnects to 2 wires so next time I can take the front panel off easily. When I got to the bearing it looked worn but not bad so I cleaned it and put it back. ... Read more
The Control Knob and Clip is an OEM part for GE washing machines and dryers. It attaches directly to the control shaft and is used to set the machine's cycles and settings. This knob allows for easy adjustment of washing or drying operations, making it a user-friendly interface for managing the appliance's functions.
Symptoms of a bad Control Knob and Clip include:
Causes of a bad control knob and clip can include physical damage from excessive force, wear and tear from frequent use, or degradation of the materials due to age or environmental factors.
Replaced rear bearing, upper and lower felts, drive belt. Have repaired dryer before for same problem years ago, knew what to do, on line diagrams helped to move memory. Cleaned all accumulated lint out of machine.Belt was changed only out of age.Looked good but thought to be on safe side. Read more
The Handle White is an OEM part for GE dryers. This part ensures a seamless fit and finish, matching the original design and color of GE dryers. The handle provides a comfortable grip for opening and closing the dryer door, making laundry tasks more convenient and less cumbersome.
Causes of a bad handle can include physical stress from pulling or accidental impacts, material fatigue over time, or environmental factors that weaken the plastic.
Symptoms of a bad Handle White include:
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
My husband found the exact handle we needed to replace the one on our dryer at AppliancePartsPros.com and we ordered it. When it came, we replaced it. I know this sounds like a simple story, but honestly, it's much more. For weeks, this broken dryer handle was driving me crazy. Finally, my husband realized that AppliancePartsPros would likely have the part--and they did. We ordered the part on a weekend and got it on Monday. I couldn't believe it. We think this place is awesome. In the... Read more
The Door Strike is an OEM part for GE dryers. This component is crucial for ensuring that the dryer door latches properly when closed. It interacts with the door catch mechanism to secure the door during operation, preventing it from opening unexpectedly, which ensures the dryer operates safely and efficiently.
Symptoms of a failing Door Strike include:
Causes of a bad door strike can include wear and tear from regular use, physical damage from slamming the door or mishandling, and misalignment caused by repeated opening and closing.
Note: If the door catch is also needed, use part number WE1M1011.
Replaced door strike and door latch Read more
The Door Latch is an OEM part for GE dryers. This part ensures the dryer door stays securely closed during operation, activating the safety switch to allow the dryer to operate. The latch mechanism engages with the door strike to lock the door, preventing it from opening while the dryer is running, which is essential for both safety and proper functioning of the appliance.
Causes for replacement can include normal wear and tear, accidental damage, or a misalignment that prevents the door from securely latching.
Symptoms of a bad Door Latch include:
The Lint Filter is an OEM part for GE dryers. This filter captures lint and debris from the laundry load, preventing it from clogging the dryer vent and ensuring efficient airflow. Properly maintaining the lint filter helps improve drying performance, reduces energy consumption, and prevents potential fire hazards.
Causes of a bad lint filter can include tears or cracks from regular use, accumulation of lint and debris that cannot be cleaned out, or warping due to heat exposure. A compromised lint filter can lead to decreased drying efficiency and potential safety issues.
Symptoms of a bad lint filter include:
Sent an e-mail to AppliancePartsPros.com to make sure the filter I was ordering would fit my dryer model. Upon receipt, I simply replaced it. Read more
The Front Drum Support Bearing Glide is an OEM part for GE dryers. Each dryer utilizes three of these parts, and they should be replaced as a set for optimal performance. This drum glide is 2-5/8 inches long and 1/2 inch wide. They provide smooth rotation for the dryer drum by supporting its front as it turns.
Causes of a bad front drum support bearing glide can include normal wear and tear over time, excessive load weights, or debris accumulation that can cause friction and damage. When the glide wears out, it can lead to increased noise levels and potential damage to other dryer components.
Symptoms of a bad front drum support bearing glide may include:
After taking off the top and front panels to access the drum, it was easy to see what the problem was. The front drum support was worn through and the 3 drum support glides were gone. The rear drum bearing was also completely worn out. And while I had the dryer apart I also replaced the idler pulley and drive belt. The only hard part was putting the drive belt back on the motor shaft and idler pulley. The dryer is back to drying clothes like a new machine. Read more
The Timer Knob is an OEM part for GE dryers. It is a component that allows users to select and control the drying cycles and settings on their dryer. Designed with durability and ease of use in mind, this knob fits directly onto the timer shaft, providing a reliable interface for setting the dryer's timer.
Over time, the timer knob can become worn or damaged due to frequent use or accidental impacts. A malfunctioning knob may not engage properly with the timer shaft, making it difficult or impossible to set the dryer cycle.
Symptoms of a bad Timer Knob include:
Amazing story of speed & quality! Ordered on Friday 4pm, had parts in hand on 2pm on Sat, finished repair by 4pm ... 24hrs! The repair video was 100% on target. Replaced the rear drum bearing, front slides/glides, and the belt (cheap insurance!). All parts were exactly as described on APP.com. I (and my wife) couldn't be happier with the repair, and the exceptional service of APP! Do not be timid about trying this repair yourself. Take your time and watch the video. Priceless! Recommend... Read more
The Blower Wheel is an OEM replacement part for GE dryers. It has a role in the air circulation within the dryer, aiding in the even and efficient drying of clothes. The blower wheel, connected to the motor, helps in expelling the moist air out of the dryer through the exhaust vent during the drying cycle. Causes of a malfunctioning blower wheel are typically wear and tear from regular use, the accumulation of lint or debris, or damage to the wheel’s fins or central hub, which can impact its rotation and air circulation capability. Symptoms of a bad Blower Wheel include:
New wheel didn't look different than the other wheel, but we put it on, it works and we're very happy. Read more
The GE clamp and screw kit is an OEM replacement part responsible for securing the dryer blower wheel in place. This kit consists of two clamps and a screw, designed to ensure the blower wheel remains firmly attached to the motor shaft. The clamp maintains the blower wheel's stability and prevents it from coming loose during the drying process. The blower wheel creates the airflow necessary to circulate hot air and efficiently dry clothes.
Over time, clamps and screws can become loose or corroded due to regular use, vibrations, or exposure to moisture. Improper handling during maintenance or repairs can also lead to damage or loss of these small but essential parts.
Symptoms of a bad Clamp and Screw Kit include:
Had to remove the front and top panel on the dryer, disconnect the belt and remove the drum. From there it was two screws to slide out the motor assembly with the fan attached and one bolt to remove the clamp and screw kit holding the fan in place. They kit was worn and was allowing the fan to move forward and back on the motor shaft. Once replaced it took about 5 minutes to reassemble and my dryer now purs like a kitten. Read more
This Dryer Drum Front Support Bearing is an OEM part compatible with GE dryers. It is responsible for supporting and stabilizing the dryer drum during operation. As the drum rotates, the front support bearing helps to maintain its proper alignment and reduces friction between the drum and the front panel. It measures 15 inches in height and has an interior width of 20 1/2 inches. It does not include the 3 drum glides, which are used and sold separately.
Causes of a bad dryer drum front support bearing can include normal wear and tear over time, excessive load on the drum, or lack of proper lubrication.
Symptoms of a bad dryer drum front support bearing may include:
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
Note: For drum glides order WE3X87.
The Rotary Start Switch is an OEM replacement part for GE dryers. It is silver and black in color, with a white D-shaped shaft. The rotary start switch is found inside the dryer control panel, and when actuated, it starts the dryer. Causes of a bad start switch include prolonged use resulting in normal wear and tear, internal component failure, or accidental external damage. Symptoms of a bad start switch are:
This is a genuine OEM part that works for some models of GE, and Hotpoint models.
Ordered parts arrived in two days. Ten minute fix with one wrench. Should have done it years ago. Read more
This dryer motor kit powers the drum and blower. Replacing a weak or failed motor restores proper tumbling and airflow so the dryer starts reliably and dries loads more evenly.
Replaced the motor with a new one, if I can offer any advice about doing this job, make sure to keep track of where each wire goes on the motor and whatever wires need to be disconnected. There are a few good video's online showing how to do this job and can save you a lot of time and frustration. Read more
Bearing only, to get complete assembly order WE25M40