Ddt575sgfoww Parts

This dishwasher turbidity sensor assembly monitors water clarity in the sump and reports to the control so it can adjust wash time and rinses for optimal cleaning. Replacing a failed sensor can restore normal cycle decisions and performance.

• Measures wash-water clarity (soil/turbidity) and sends data to the control
• Helps optimize cycle length, number of rinses, and water usage
• A faulty sensor may cause unusually long or short cycles
• Can contribute to poor cleaning or failure to complete a cycle
• May set a sensor-related code in diagnostics on some models

• Disconnect power at the breaker and shut off water before servicing
• Access from the bottom/front of the dishwasher; place a towel to catch residual water
• Unplug the wire connector, rotate the sensor to unlock, and remove; ensure the seal seats properly when installing the new part
• After installation, check for leaks and run a test cycle

This dishwasher fill hose routes incoming water from the inlet valve into the tub. Replacing a brittle or leaking hose helps restore proper filling and reduces the risk of water leaks under the unit.

• Carries fresh water from the inlet valve to the dishwasher during the fill cycle
• Helps maintain correct water level for reliable wash performance
• Common symptoms of a failed hose: leaks near the toe kick, slow fill, or no fill
• Replaces hoses that are cracked, swollen, kinked, or deteriorated

• Disconnect power and shut off the water supply before service
• Place a towel or shallow pan to catch residual water
• Access behind the lower kick panel; transfer existing clamps/fittings as needed
• Route the hose without kinks, fully seat connections, restore water, and check for leaks during a test cycle

The Upper Spray Arm Support is an OEM replacement part for GE dishwashers. It is installed within the dishwasher tub below the upper spray arm, and is responsible for securely mounting and holding the upper spray arm in place during operation.

Symptoms of a bad upper spray arm support include:

• Vibration or noise from an unsecured spray arm
• Improper alignment of water spray pattern  
•  Restricted rotation of the spray arm during washing
• Leaks at the tub connection point

Causes of a bad spray arm support can be from cracks or breaks that compromise its structure, or wear over extended use without replacement. 

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Turbidity Sensor Assembly is an OEM part for GE dishwashers. It is responsible for monitoring the cleanliness of the water during the dishwashing cycle. The turbidity sensor measures the level of particles and impurities in the water, allowing the dishwasher to adjust the cycle accordingly. It helps prevent issues such as over-washing or under-washing, resulting in clean dishes every time.

A bad Turbidity Sensor Assembly can lead to improper cleaning performance or cycle errors. Causes of a bad turbidity sensor can include sensor malfunction, damage to the sensor, or buildup of residue affecting its accuracy.

Symptoms of a bad Turbidity Sensor Assembly include:

• Incomplete or inadequate cleaning of dishes
• Error codes related to water cleanliness or turbidity
• Extended or shortened cycle times without reason
• Persistent residue or film on dishes after the cycle

Replace your faulty or damaged Turbidity Sensor Assembly with this genuine OEM GE part to ensure precise cleaning performance and spotless results. 

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This clamp kit replaces worn Piranha-style clamps used in the dishwasher's wash system. Restores a tight, reliable seal on internal connections to help prevent leaks and maintain proper water circulation for consistent cleaning results.

• Secures internal hose and pump connections within the wash system
• Helps stop water leaks caused by loose, stretched, or damaged clamps
• Supports proper circulation and wash performance by keeping joints sealed
• Common symptoms: water under the unit, drips at hose joints, loose connections, vibration or rattling from the sump area

• Disconnect power and shut off the water supply before servicing
• Access the sump/pump area from the front toe-kick or by pulling the unit out as needed
• Replace one connection at a time; position and fully seat the new clamp(s) on clean hose/barb surfaces
• Restore power/water and run a short cycle to check carefully for leaks before reinstalling panels

Size: 8-18 AB TSQ 5/8 SS

This is a machine screw used to secure dishwasher components. The 10-32 thread and 3/8-inch length with an integrated hex washer head provide a firm, vibration-resistant hold to keep parts properly fastened.

• Secures brackets, panels, or internal assemblies in the dishwasher
• Helps prevent looseness, rattling, or misalignment during operation
• Common symptoms of a missing/stripped screw include panel movement, vibration, or loose mounting points

• Disconnect power and shut off water before servicing
• Use the correct nut driver or socket to avoid stripping the head
• Replace any damaged or missing screws in matching locations
• Do not overtighten; snug to manufacturer's torque guidance when available

This dishwasher hose clamp secures a hose to its fitting to maintain a tight, leak-resistant seal during operation. Replacing a worn or corroded clamp helps stop drips and keeps fill, drain, or circulation lines firmly in place.

• Secures dishwasher hoses to fittings on pumps, valves, or drain outlets
• Helps prevent water leaks at hose connections
• Keeps hoses from slipping off under vibration and water pressure
• Typical symptoms include water under the unit, dampness in the cabinet, or a hose connection that feels loose

• Disconnect power and shut off water supply before servicing
• Access the hose connection (toe-kick or rear/side panels may need removal)
• Seat the hose fully on the fitting, position clamp just behind the barb/ridge, and secure without over-tightening
• Run a short test cycle and check all connections for leaks

This top-control console is the panel at the upper edge of the dishwasher door. It forms the interface area for selecting cycles and protects the components behind it, helping keep the controls aligned and presentable.

• Houses and protects the user interface at the top edge of the door
• Provides the interface area for cycle and option selection
• Restores fit and appearance when the original console is cracked, warped, or loose
• Help if buttons feel misaligned due to a damaged console housing

• Disconnect power at the breaker before servicing; shut off water if moving the appliance.
• Open the door and remove perimeter screws to separate inner/outer door panels; support wiring when removing the console.
• Transfer any model-specific components from the original console to the new console; avoid pinching harnesses during reassembly.
• Restore power and selections engage and the door latches properly.

The Filter Adapter is an OEM component specifically designed for GE dishwashers. Located inside the dishwasher tub, it functions to strain out large food particles from water before it reaches the wash arms.  The adapter holds the removable wash/rinse filters in place during operation, functioning as an extension of the filtration system. 

Causes of a bad filter adapter can include cracks or breaks compromising its sealing surface, wear and tear deforming filter retention features over time, or buildup inhibiting functionality.

Symptoms of a bad filter adapter include:  

• Loose or falling out removable filters during washing  
• Bypassing of food particles around compromised seals
• Reduced lifespan of disposable filters placed in a faulty adapter
• Debris accumulation impacting spray arm performance

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This arm hinge assembly restores smooth, controlled movement of a hinged component in your dishwasher, helping maintain proper alignment and reliable operation. Replacing a worn or broken hinge can reduce binding, squeaks, and misalignment that affect performance. What it does:

• Provides the pivot point and support for a hinged assembly
• Maintains alignment to ensure correct engagement and sealing
• Helps ensure smooth opening/closing motion without binding
• Replaces a hinge arm that is cracked, bent, or worn
• Common signs: stiff or uneven movement, squeaking or popping noises, misalignment, or visible damage

• 1 arm hinge assembly

• Disconnect power and water before servicing
• Support the door or movable assembly to relieve tension while removing the hinge
• Note orientation and transfer any side-specific hardware from the original part
• After installation, check for smooth motion and proper alignment before restoring power and water

Arm hinge assembly is the pivoting hinge that supports and guides the appliance door, restoring smooth, stable opening and closing for proper alignment and operation. Replacing a worn hinge helps stop sagging, misalignment, and scraping noises. What it does:

• Supports the door pivot and maintains proper hinge alignment for smooth opening/closing.
• Helps the door latch and seal correctly by keeping the door level and aligned.
• Common symptoms: door hangs or sags, door won't close or latch, rubbing or scraping noises during movement.
• Replaces a bent, worn, or broken hinge arm to restore normal door operation.

• Disconnect power before starting any service.
• Use proper hand tools and support the door while removing/installing the hinge to avoid damage or injury.
• Align the hinge and operate the door several times before fully tightening fasteners; follow manufacturer torque/fastening guidance if available.

The Upper Rack Bracket Assembly is an OEM replacement part for  GE dishwashers. It is located inside the dishwasher tub and functions to securely mount the upper dish rack. It allows for adjustable height positioning and prevents rack movement during washing.

Causes of a bad upper rack bracket assembly can include cracks or breaks in the mounting points, stripped screw holes allowing rack sway, or deformities preventing proper seating.

Symptoms of a bad upper rack bracket assembly include: 

• Loosening or detaching of the upper rack during the cycle  
• Restricted rack adjustment or inability to set desired height
• Noise or vibration from an unsecured rack vibrating against the tub

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Vent Fan Assembly is an OEM replacement part for GE dishwashers. As a key ventilation component, the vent fan is responsible for drawing moisture-laden air out of the dishwasher tub and venting it outside during and after the wash cycle. It plays an important role in effectively drying dishes and preventing mold or odor issues.

Causes of a bad vent fan include a failing motor, broken or cracked fan blades, or an obstructed vent opening. 

Symptoms of a bad vent fan include:

• Incomplete or slow drying of dishes
• Excess moisture remaining in the tub at the end of the cycle  
• Mold or mildew growth inside the dishwasher
• Strange noises or vibrations coming from the vent area

Over time, the vent fan motor and blades can degrade due to continuous use. This part is also compatible with ASKO, Crosley, Inglis, Magic Chef, RCA, and some Kenmore models.
 

This is a 6-20 machine screw, 3/8 inch length, used to secure trim, panels, or small components on compatible cooking appliances. Replacing a missing or damaged screw helps keep parts tight and prevents rattles or shifting during use.

• Fastens brackets, panels, or trim in the appliance chassis
• Helps restore a secure fit when the original screw is stripped or lost
• Can resolve issues like loose trim, minor rattling, or misaligned panels
• Nickel finish for corrosion resistance in warm, humid environments

• Disconnect power and allow appliance to cool before servicing
• Remove only the necessary adjacent fasteners to access the mounting point
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing
• Replace any missing clips or spacers originally used with the screw

This detergent plate is the replacement dispenser component that holds and releases detergent during the wash cycle, ensuring detergent is delivered when the machine runs for proper cleaning performance. What it does

• Holds detergent inside the dispenser area until the wash cycle calls for release.
• Opens or allows detergent to be flushed into the wash chamber at the correct time.
• Common symptom: detergent stays in the dispenser and doesn't release, leaving dishes or laundry soiled.
• Common symptom: damaged, cracked or warped plate can prevent proper release or seating of detergent.

• One detergent plate

• Disconnect power (and water if applicable) before accessing the dispenser to avoid shock or injury.
• Handle the plate carefully; plastic parts can crack if forced or over-tightened.
• Remove the door/dispenser trim per your model's service instructions to access the plate; reinstall ensuring proper alignment so the dispenser seals and operates correctly.