Dh43 Parts

The Dryer Belt is an OEM part for GE dryers. This belt wraps around the drum, motor pulley, and tension pulley, enabling the drum to spin during the drying cycle. It plays a crucial role in the mechanical operation of the dryer.

Common causes of a bad dryer belt include normal wear and tear from repeated use, overloading the dryer, or damage from obstructions inside the drum.

Symptoms of a bad dryer belt include:

• The drum not turning when the dryer is running
• A burning smell during operation
• Unusual noises such as thumping or squeaking
•  The dryer stopping mid-cycle

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Rear Drum Bearing Kit is an OEM part for GE dryers. The kit includes a rear bearing, shaft support, ball shaft, ball bearing, ball bearing retainer, high-temperature lubricant, and screws required for installation. 

Causes of a bad rear drum bearing can include normal wear and tear over time, exposure to excessive heat, or heavy use that puts strain on the bearing. A failing bearing can cause the drum to become misaligned, creating friction and noise during operation.

Symptoms of a bad rear drum bearing include:

• Squeaking or grinding noises when the dryer is running
• The drum being difficult to turn manually
• Clothes not drying evenly due to improper drum rotation
• The dryer stopping mid-cycle or failing to start

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This dryer safety thermostat monitors internal temperature and opens the circuit if the unit overheats, protecting the heater and wiring. Replacing a failed thermostat restores proper over-temperature cutoff and safe, consistent drying performance. What it does:

• Monitors air temperature at the heater/exhaust path
• Interrupts power to the heating element if temperatures exceed its limit
• Helps prevent overheating and thermal damage
• Common symptoms can include: no heat, heat cutting out early or overheating, or the dryer shutting off on high heat

• 1 safety thermostat

• Disconnect power before service; for gas dryers, also shut off the gas supply
• Typically mounted on the heater housing or exhaust duct; note wire positions and transfer one at a time
• Secure with existing hardware and ensure tight electrical connections
• After replacement, clean the lint filter, vent hose, and exhaust duct to ensure proper airflow and prevent repeat overheat trips

This drum glide provides a smooth, low-friction surface at the front of the dryer drum. Replacing worn glides restores quiet, even drum rotation and helps prevent scraping and fabric damage.

• Supports the front of the drum and allows smooth rotation on the front bearing/bulkhead
• Reduces friction and metal-on-metal contact to minimize noise and wear
• Helps maintain proper drum alignment and spacing at the door opening
• Common symptoms of a worn glide: scraping or squealing while tumbling, drum hard to turn, brown/black marks on clothes, or snagging at the front edge

• Disconnect power; shut off gas supply for gas dryers before servicing
• Remove the top and front panel/bulkhead to access the front drum support
• Support the drum when the front panel is off to avoid stressing the rear bearing
• Many models use multiple glides; inspect all front support wear items (glides/slides and felt seal) and replace as needed for even wear

This thermal limiter is the dryer's high-limit thermostat. It monitors temperature and opens the heating circuit if the dryer overheats, helping protect components and allowing the appliance to operate safely.

• Provides over-temperature protection for the dryer's heating circuit
• Opens the circuit when excessive heat is detected to prevent damage
• If failed open, the dryer may run but not heat
• Repeated tripping can cause intermittent heat and longer dry times

• Disconnect power and allow the dryer to cool before servicing; shut off gas supply for gas models
• Handle wiring carefully; transfer leads one at a time and mount the limiter in the original location/orientation
• Use a multimeter to check continuity
• Clear lint buildup and prevent repeat overheating

This gas dryer igniter is the glow-bar element that lights the burner so your dryer can produce heat. Replacing a worn, cracked, or non-glowing igniter restores reliable ignition and consistent drying performance.

• Heats and glows to ignite gas at the burner assembly
• Common symptoms: dryer runs but no heat, igniter does not glow, burner won't light
• Visual cracks or a non-heating element indicate failure

• Disconnect power and shut off the gas supply; allow the burner area to cool before service
• Handle by the base only; the igniter element is extremely fragile—do not touch or bump it
• Transfer bracket and wiring from the old part if needed; reuse existing hardware
• Restore gas and power, then the igniter glows and the burner lights properly

This thermostat control replaces the oven's temperature-regulating switch to help restore accurate bake and broil temperatures. It helps the oven reach and hold the set temperature for more consistent cooking results. What it does:

• Senses oven temperature and cycles the heating element or gas valve to maintain the selected temperature.
• Restores consistent bake and broil performance when the oven overheats, underheats, or cycles on and off erratically.
• Can resolve issues with uneven cooking, long preheat times, or temperature that doesn't match the setpoint.
• Interfaces with the oven control harness to manage temperature regulation during cooking cycles.

• Disconnect power to the appliance at the breaker before starting any repair.
• Handle the control carefully to avoid damage to terminals and mounting hardware.
• Verify wire connections and routing before restoring power; secure mounting per the oven's service instructions.

For complete bearing kit order WE25X10001.

This mechanical oven timer restores simple dial-based timing and end-of-cycle alerts so you can set cook times and receive audible reminders. It replaces a worn or non-advancing timer to bring back reliable basic timing functions. What it does:

• Advances and times cook/clean cycles so the oven rings when a set time ends
• Restores manual timing when the clock/timer no longer advances
• Replaces a timer that fails to sound the end-of-cycle buzzer
• Provides a direct, dial-based alternative to electronic controls on compatible units

• Always disconnect power to the appliance before beginning service
• Access typically requires removing the control panel or console; support the console while detaching the timer
• Align the timer shaft and knob carefully during installation to avoid damage

This replacement part is a dryer clip, and it is intended for use in different types of appliances. This is a genuine replacement part made by General Electric. This dryer clip is typically found on dryers and there are usually multiple clips on one appliance. These clips help hold the front panel in place and secure so that it does not come off during the drying cycle. A new dryer clip might be needed if the front panel of the dryer is off balance or not attached correctly. It is possible that the clips can become loose over time as the appliance is prone to shaking and vibrating. The clips are important as it keeps the dangerous parts covered. If the entire front panel can be lifted off then it is time to replace the dryer clips. These clips are sold individually even though dryers typically have more than one. This clip is a genuine OEM part.

A replacement pan head screw used to fasten appliance panels and components. Its standard #8 coarse thread and 3/8-inch length secure trim, brackets, and small assemblies for stable operation. What it does:

• Fastens panels, brackets, and small parts in household appliances
• Replaces stripped, rusted, or missing #8-18 pan head screws
• Restores secure mounting where vibration or wear caused looseness
• Works with sheet-metal or threaded inserts designed for #8-18 screws

• Disconnect power to the appliance before beginning any repair
• Use the correct #2 Phillips or compatible driver to avoid cam-out
• Thread in straight and tighten until snug; avoid over-tightening to prevent stripping
• Keep small screws away from children and dispose of old fasteners safely

This dryer bearing bracket secures the drum's rear bearing to keep the drum aligned and rotating smoothly. Replacing a worn bracket can help reduce drum wobble, scraping noises, and uneven drum rotation. What it does:

• Supports and locates the rear drum bearing to maintain proper drum alignment.
• Helps prevent the drum from wobbling, rubbing, or scraping against the cabinet.
• Can reduce or eliminate grinding, squealing, or thumping noises caused by a loose or damaged rear support.
• Works with the dryer's rear bearing assembly to enable consistent drum rotation.

• Disconnect electrical power (and gas, if applicable) before beginning any repair.
• Access typically requires removing the dryer drum and rear bulkhead.
• Inspect the bearing, shaft, and surrounding glides; replace any worn components to prevent repeat failure.

This is a dryer timer. The part is used to control the dryer's cycles. If this part is damaged or faulty, the dryer may skip cycles, fail to complete them, or get stuck in a particular cycle.Although the dryer timer tends to be durable, there's a chance that it could wear out over time. It could also become damaged from misuse. Before beginning the repair, unplug the dryer.The dryer time will work with models from GE. This is a genuine OEM replacement part. It was sourced from the manufacturer, and it is sold individually.