Dlg7051v Parts

This moisture sensor connector assembly links the dryer's sensor bars to the control to monitor fabric dryness and adjust cycle time. Replacing a damaged or loose harness restores consistent Auto Dry operation.

• Connects the moisture sensor bars to the main control for Auto Dry feedback
• Transmits the low-voltage signal used to determine when clothes are dry
• Failure may cause Auto Dry to end too soon, run too long, or deliver inconsistent results
• Typical issues include broken wires, loose/corroded terminals, or a heat-damaged plug

• Disconnect power; if gas, shut off gas supply before service
• Access the moisture sensor area at the front/lint housing
• Match routing and clips, seat terminals fully on the sensor tabs, and secure the connector
• Keep wiring clear of sharp edges and moving parts; reassemble and test a Sensor Dry cycle

This duct assembly channels airflow inside the appliance to guide exhaust and internal air between components. Replacing a damaged or obstructed duct helps restore proper airflow and can reduce poor performance or long cycles. What it does:

• Directs exhaust and circulation air between internal components to maintain airflow
• Prevents leaks that can reduce efficiency or cause longer cycle times
• Helps avoid overheating or moisture build-up from restricted airflow
• Reduces rattling or vibration caused by a cracked or loose duct

• Disconnect power (and turn off gas supply for gas appliances) before beginning work.
• Handle edges carefully — sheet metal can be sharp; wear cut-resistant gloves.
• Ensure duct is seated and fastened to create a tight seal where it connects to other components.
• After reassembly, run a test cycle to confirm airflow and proper operation.

The Blower Wheel is an OEM part for LG dryers. This part circulates air through the dryer drum and out the exhaust vent, ensuring proper airflow for efficient drying of clothes.

Causes of a bad blower wheel can include accumulation of lint and debris, wear and tear over time, or physical damage due to foreign objects entering the blower housing.  

Symptoms of a bad blower wheel include:

• Reduced or no airflow from the exhaust vent
• Unusual noises such as rattling or squealing during the drying cycle
• Clothes taking longer to dry or remaining damp
• Overheating or frequent shutdowns of the dryer

This OEM LG part is also compatible with some Kenmore models.

This drying rack sits inside the dryer drum to hold items stationary while warm air circulates around them. It lets you rack-dry shoes and delicates without tumbling, helping prevent banging and scuffing that can happen when items rotate. What it does:

• Provides a stable platform inside the drum for stationary drying
• Allows heated air to circulate around items while preventing tumbling
• Used for shoes, sweaters, hats, and other items approved for rack-dry cycles
• If missing or damaged (cracked frame, broken tabs, poor seating), you may hear rattling or be unable to rack-dry items

• 1 drying rack

• Disconnect power and allow the drum to cool before inserting or removing the rack
• Insert the rear of the rack into the drum supports, then rest the front edge on the door opening; ensure it is level and fully seated
• Load items evenly and do not overload; use the rack-dry or low-heat settings recommended in your owner's manual
• Remove the rack before resuming standard tumble cycles

This dryer duct assembly channels air from the drum to the blower and exhaust. Replacing a cracked or warped housing restores proper airflow, helps prevent lint bypass, and supports consistent drying performance.

• Directs and seals airflow between the drum and blower housing
• Helps maintain drying efficiency by minimizing leaks and lint bypass
• Damage or warping can lead to long dry times and reduced airflow
• Signs of failure include visible cracks, melted spots, or air/lint leakage around the duct area

• Disconnect power; for gas models, turn off the gas supply
• Access from the front by removing the top and front panel
• Note fastener locations and any attached brackets/harnesses, then transfer them to the new assembly
• Vacuum lint from internal ducting and verify seals before test run

For propane order 383EEL3002A.

This distortion spring applies the correct tension within the dryer mechanism so parts return to position and operate smoothly. Replacing a fatigued or broken spring helps prevent loose movement, rattling, and inconsistent operation of the related assembly. What it does

• Provides the designed return/tension force for the associated dryer mechanism
• Helps maintain alignment and smooth movement of moving parts
• Can reduce rattling or squeaking caused by weak or missing spring tension
• Symptoms include components not returning to position or intermittent operation

• One distortion spring

• Disconnect power; for gas dryers, also shut off the gas supply
• Allow internal components to cool before service
• Control the spring during removal/installation—springs are under tension and can snap back
• Note the original spring orientation and attachment points to ensure proper reassembly

This adjustable leveling leg screws into the dryer base to support and stabilize the cabinet. Replacing a worn or missing foot helps level the appliance, reduce vibration and noise, and keep it steady on uneven floors.

• Provides threaded height adjustment to properly level the dryer
• Stabilizes the cabinet to minimize rocking, vibration, and walking
• Replaces a broken, worn, or missing foot
• Common symptoms: dryer wobbles, is hard to level, or makes rattling/vibration noise

• Disconnect power; shut off gas supply for gas models
• With a helper, carefully tilt or raise the dryer for access
• Unscrew the old leg; thread the new leg into the base by hand, then adjust with a wrench until the dryer sits level and stable
• Ensure all legs contact the floor and the dryer does not rock

Adapt your gas dryer for propane with this LP conversion kit. It provides the correct orifice and regulator adjustments needed so the burner fires properly on LP fuel, helping ensure safe operation and consistent drying performance after a fuel change.

• Converts a compatible gas dryer from natural gas to liquid propane (LP)
• Helps ensure proper burner flame characteristics on LP
• Appropriate when moving to a home with propane or changing utilities
• Symptoms can include weak heat, improper flame, or sooting

• Disconnect power and shut off gas before servicing
• Installation and regulator/orifice adjustments must be performed per the service manual
• After installation, leak-check all connections and verify proper burner operation
• Do not attempt conversion without the correct kit for your specific model

This replacement screw secures appliance components in their proper position. Use it to restore a tight, rattle-free fit when the original fastener is missing, stripped, or corroded. What it does:

• Fastens brackets, panels, or trim to keep assemblies aligned and secure
• Helps prevent vibration, rattling, and gaps from loose hardware
• Restores proper attachment when a screw is lost, worn, or damaged
• Common symptoms: loose panel/handle, misalignment, rattling, or a missing screw

• Disconnect power; shut off water or gas before service
• Match location to the original; start threads by hand to avoid cross-threading
• Use the correct driver bit; do not overtighten (especially into plastic)
• If the original hole is stripped, repair threads before installing the new screw

This factory fastener is the customized screw used to secure components on compatible LG appliances. It replaces missing or damaged screws to keep brackets, panels, and covers tight so parts stay aligned and rattle-free.

• Secures brackets, panels, trim, or covers at their mounting points
• Helps maintain alignment and reduce looseness, gaps, squeaks, and rattling
• Replaces stripped, rusted, or missing screws caused by vibration or wear
• Restores proper hold so components stay in place during normal use

• Disconnect power; shut off water to the appliance if applicable
• Use the correct driver bit and apply straight, firm pressure to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• If replacing multiple screws, swap one at a time to maintain alignment

Restore smooth, aligned door movement with this refrigerator door hinge assembly. A worn or bent hinge can cause sagging and poor sealing; replacing it helps the door close properly so your fridge maintains consistent performance. What it does:

• Allows the door to pivot smoothly on the cabinet
• Helps keep the door aligned for proper gasket contact and sealing
• Replaces worn or bent hinge components to restore correct door operation
• Typical symptoms: door sagging or rubbing, difficulty closing, uneven gasket contact, squeaks/clicks when opening or closing

• One hinge assembly

• Unplug the refrigerator; shut off water supply to the unit
• Support the door and use a second person to prevent dropping or misalignment
• Note/mark hinge positions and transfer any spacers or caps from the original hinge as needed
• After installation, verify even gasket contact and adjust leveling before tightening fasteners fully

This micro switch is a compact, snap-action electrical switch that sends an on/off signal when a lever, latch, or paddle is moved. Replacing a worn switch restores reliable detection and control response for the affected function.

• Converts mechanical movement into an electrical open/close signal to the control
• Commonly used for lever/paddle actuators, latches, or interlock detection within the appliance
• Safe symptom clues: no response when actuated, intermittent operation, or a function stuck on/off
• Physical clues: weak or absent "click" when pressed, heat discoloration or damage at terminals

• Disconnect power before servicing; if the product is connected to a water line, close the supply valve
• Note wire positions and terminal labels (COM/NO/NC); transfer wires one at a time to matching terminals
• Match the actuator orientation and mounting position to the original for proper operation
• After installation, verify continuity with a multimeter and test function before reassembly

This door hinge supports and pivots the appliance door so it opens smoothly and closes securely, maintaining proper alignment and latch engagement. Replacing a worn hinge restores consistent door operation and helps prevent sagging, rubbing, and incomplete closure.

• Provides the pivot point and structural support for the door
• Helps keep the door aligned for proper latching and closure
• Common signs: door sagging, rubbing, or binding during operation
• Door won't close flush or pop open unexpectedly
• Visible hinge wear, looseness, or damage

• Disconnect power to the appliance before servicing
• Support the door to relieve hinge load before removing screws or pins
• Transfer any reusable spacers, bushings, or screws from the old hinge
• After installation, verify door alignment and latch engagement; adjust as needed

This self-tapping screw fastens panels, brackets, and internal components in compatible appliances. Replace a stripped, corroded, or missing screw to restore a secure fit and help prevent vibration, rattling, and misalignment.

• Forms/engages its own threads in sheet metal or plastic for a secure hold
• Secures covers, brackets, and assemblies to maintain alignment
• Helps reduce vibration and noise from loose components
• Replace if the head is stripped/broken, threads are worn, or the screw is missing

• Disconnect power and shut off water or gas, as applicable, before servicing
• Match to the original location and hardware; use identical length and thread where specified
• Start by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving hole is damaged, repair it before installing the new screw

This replacement locker hook mounts on the dryer door and engages the cabinet catch and door switch. It keeps the door securely closed so cycles can start and continue without interruption. What it does:

• Attaches to the door and latches into the cabinet catch to secure the door
• Actuates the door switch so the appliance recognizes the door is closed
• Replaces a cracked, bent, or worn hook
• Resolves issues like the door not latching, popping open, or the unit not starting

• 1 locker hook

• Disconnect power; if gas, also shut off the gas supply
• Open the door and remove the mounting screws securing the old hook
• Position the new hook and tighten screws, reusing existing hardware
• Check latch alignment; the door closes securely and the cycle starts