Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Replaces damaged outer and inner door panels to restore appearance and maintain proper door alignment. Replace if panels are cracked, warped, or dented. Verify fit with your model number.
Replaced front panel and inner liner of door (kit), trap duct assembly, both bearing slides (gray and white), and drum front support bearing. Procedure is pretty much what one sees in the video clips. Exceptions in our case included: 1. The fact that our door latch¹ was on the front panel while the door strike² was on the door. The newer (replacement) design has the latch on the door and the strike on the front panel! 2. The new door did NOT have the door latch installed (as shown in the... Read more
Set of 12 size 8-18 mounting screws for dishwashers. Replaces lost, stripped, or missing screws for secure installation of handles and components.
Ordered the cord through appliance parts pros, with additional screws and it works! Yay after waiting months and everywhere was out. Thank you. Read more
Replacement mounting screw for dryer panels, brackets, and components. Needed when screws are missing, stripped, or damaged during repairs or disassembly.
Upon examination of the dryer, I noticed that the belt was intact, though a little worn and hard. However, I noticed that the belt had came of the idler pulley. So I put it back on and had the owners try it out on their next load of wash. It, once again failed to keep the drum turning. So I ordered a new belt and idler pulley (order # 8676164). I found it necessary to remove the drum, in order to change out the new pulley. However, while trying to reinstall the drum, we damaged some of the... Read more
Secures the drive motor to its mounting bracket. Replace if cracked, broken, or missing to keep the motor and blower aligned and stable during operation.
Replacement screw for securing dryer panels and internal components. Restores proper fit when original screws are stripped, missing, or damaged.
Hex washer head screw for refrigerators, freezers, and other appliances. Replaces lost, stripped, or damaged screws during repairs or panel assembly.
Factory replacement screw for securing dryer panels, brackets, and components. Restores lost or loose hardware to eliminate rattling and ensure proper fit.
Replaces cracked, torn, or deteriorated dryer exhaust duct hose. Connects dryer to wall vent to safely channel hot air and lint outside your home.
Replaces a worn, damaged, or misaligned dryer motor pulley. Guides the drive belt and transfers motor power to the drum for proper rotation.
Replaced belt, pulley with a 4 grove pulley. Pulley that was on there was a 3 grove pulley, Had to cut the old one off, Press on to shaft. Replaced rear drum bearing. Bearing was locked on with a snap ring. Access to it from a removable plate on the back side of dryer. Reset belt and idler puller by removing a long back plate on the bottom rear side of the dryer. None of this was shown in your Video. Read more
Ground strap assembly connects drum shaft to dryer frame for electrical safety. Replace if damaged, corroded, or causing startup squealing noise.
My GE dryer from the late 80's/early 90's was squealing when it would start up, belt or bearing I was thinking. I found a manual online that covered my model and I watched a video on this site that showed me how to take it all apart, mine was a bit different but the principles were the same. I took it apart and added some quick-disconnects to 2 wires so next time I can take the front panel off easily. When I got to the bearing it looked worn but not bad so I cleaned it and put it back. ... Read more
Dryer not starting or stopping mid-cycle? This relay switch controls power to key components. Common fix for erratic operation. Moderate DIY repair.
Metal bracket that secures the dryer motor and blower assembly in place. Replace if your mounting bracket is cracked, broken, or causing loose components.
Secures the ground wire to the dryer cabinet for safe electrical connection. Replace if missing, stripped, or corroded to restore proper grounding.
Mounting bracket that secures the gas valve assembly in your dryer. Replace if bent, broken, or missing to properly support and position the valve.
This valve elbow redirects the appliance's water line to the inlet valve, providing a secure 90° connection to help prevent kinks and ensure consistent water flow. Simple, compact replacement for a worn or damaged elbow. What it does