Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Usually ships within 4 - 14 days
This heater support secures the dryer heater assembly so it stays aligned and stable during operation, helping maintain proper airflow and heating performance. It's a direct-fit replacement designed to restore correct heater positioning. What it does:
Since I didn't take it apart it took me a minute to figure it out where the clips went. The package told me which side was which and I just...clicked them into place. No problems. Read more
This O-ring is a small rubber replacement seal that helps stop water leaks where two components meet. It restores a tight seal to reduce drips and prevent water damage from worn or cracked seals. What it does:
1. To fix the leaks from around the door, I replaced the upper and lower door seals. These were purchased in a separate transcation, so they are not the parts shown here. The upper door seal worked as intended, but the lower seal would not stay in place on the lower edge of the door during a wash. Therefore I cleaned the grease and detergent off the old seal, and installed using silicone sealer/adhesive. The plastic edge pieces for the lower seal were supplied with the kit, and they installed... Read more
This premium dispenser cam engages the dispenser mechanism to control door/lever movement and ensure reliable dispense actions. It replaces a worn cam to restore proper dispenser function and consistent operation. What it does:
Replaced timer,and timer cam. Read more
Replaced the timer in about 20 minutes. Fills completely each time now. Read more
Color: Black.
I had no hope of separating the panel from the frame without damaging the frame since the two parts were rusted pretty badly and the screws holding the panel to the frame were completely beyond salvage. So I had to replace both the panel and the frame. I ended up removing the electrical/electronic connections, removing the panel/frame from the hinge and then replacing it with the new parts. Took about 90 minutes but the hardest part was removing other items from the rusting frame without... Read more
The Thermostat Clip is an OEM part for Whirlpool dishwashers. It plays an important supporting role by securely fastening the thermostat sensor inside the wash chamber.
Symptoms of a faulty Thermostat Clip can include:
Causes could arise from typical wear and tear stresses weakening plastic retaining clips. Exposure to harsh detergents may also erode clip material integrity over time.
This OEM replacement part is compatible with KitchenAid, Jenn-Air, Kenmore, and select Hotpoint and Roper dishwasher models as well.
Size: 8-32.
This lower wash arm bearing keeps the dishwasher's lower spray arm turning smoothly so dishes get even water coverage. It replaces a worn bearing to reduce noise and restore proper spray-arm rotation. What it does:
After discovering that these parts were not the problem. I found replacements for the impeller online and replaced those parts plus these parts. Disassembly was difficult and one bolt inside of the motor shaft had to be drilled out. Other than that, these replacement parts were an exact fit and the video on your page made the replacement no problem. Read more
The Latch Switch Kit, an OEM Replacement Part is designed to ensure the safe operation of your Whirlpool dishwasher. The kit includes two microswitches and a wiring harness. It prevents the appliance from running when the door is open. If defective, the door switch may prevent the dishwasher from operating even when the door is closed.
Causes of a bad door switch can include wear and tear, exposure to moisture, or a broken actuator.
Symptoms of a bad door switch include:
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
I ordered the Door Switch Kit, along with a few other items. However, the switch kit was all that was needed. Isimply followed the instructions that came with the kit. It was necessary to cut the wires which connected to the wire assembly in the door of the dishwasher. I then connected the pieces from the switch kit and then connected the end pieces to the door. I closed the door, and started up the dishwasher. It worked as well as before. Read more
Very easy to repair. All the parts fit perfect. Entire repair took 20 mins. Read more