Efls527uiw Parts

The Hinge Assembly is an OEM replacement part for Frigidaire washing machines. It is the mechanism that allows the washer door to open and close properly. 

Symptoms of a bad hinge assembly include:

• Loose, wobbly, or unstable door movement  
• Difficulty latching or sealing the door fully shut
• Excessive noise or vibration from the hinge area 
• Misaligned or warped door position

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Motor is an OEM part for Frigidaire washing machines. As an integral internal part, the motor uses its rotating power to agitate clothes and spin water out during the wash and spin cycles. 

Symptoms of a bad motor include: 

• The washer fails to start or complete cycles
• Loud grinding noises emanating from inside the washer cabinet 
• Vibration issues causing the washer to shake excessively
• The drum refusing to spin 

Causes of motor failure can be normal wear and tear over time, impact or water damage corroding motor windings, or burned-out motor starter components like capacitors or brushes.

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

The Motor Control Board is an OEM part for Frigidaire washing machines. It is an electronic control center that regulates power to electrical components including the drive motor, timers, switches and sensors.  

Causes of failure can be water damage, loose or corroded connections over time, or defects in the electronic components themselves.

Symptoms of a bad motor control board include:

• The washer not starting or powering on at all
• Inability to select or change wash cycles
• Erratic or failing responses to button presses
• Odd sounds, smells or smoke coming from internal areas

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Housing is an OEM part for Frigidaire washers. It holds the dispenser cup securely in place and ensures proper functioning of the detergent and fabric softener dispensing system.

This housing is specifically designed to fit within your Frigidaire washer, providing stability and support to the dispenser cup. It helps prevent leaks and ensures that the detergent and fabric softener are dispensed accurately during the wash cycle.

A bad housing can be caused by wear and tear, damage, or improper installation. Signs of a faulty lower housing include leaks, loose dispenser cup, or improper dispensing of detergent or fabric softener.

Symptoms of a bad housing include:

• Leaks or drips from the dispenser
• Loose or wobbly dispenser
• Improper dispensing of detergent 

Replace your defective or damaged housing with this genuine OEM Frigidaire part to restore your washer. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

The Leveling Leg is an OEM part for Frigidaire washing machines. These legs are designed to securely hold the washer in place while allowing adjustable height for proper leveling on uneven surfaces.

Causes of a bad leveling leg can include threads stripping or seizing due to regular height adjustments over time, as well as cracks or breaks from heavy loads or impacts.

Symptoms of a faulty leveling leg include:

• Excessive vibrating or horizontal movement of the washer during spin cycles
• Bowing or sagging of the washer cabinet
• Draining or filling issues due to improper drainage angle
• Premature component wear from long term poor leveling

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This leveling leg threads into the base of your appliance to level and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking, walking, and vibration, protecting the machine and floor for smoother, quieter operation. What it does:

• Provides adjustable height to level the appliance on uneven floors
• Stabilizes the cabinet to reduce vibration and noise
• Replaces a cracked/missing foot or leg with stripped threads
• Helps address rocking, walking, excessive vibration, rattling, or difficulty leveling

• 1 leveling leg

• Disconnect power; turn off water supply and move/tilt the appliance safely with a helper
• Thread the new leg by hand to avoid cross-threading
• Adjust all legs until the unit is level front-to-back and side-to-side
• If the leg uses a jam nut, tighten it to lock the setting; recheck level after initial use

Replacement mounting screw that secures panels, brackets or small components in compatible appliances. Installs quickly to replace stripped or missing fasteners and help stop rattling and restore proper alignment. What it does:

• Fastens panels, trim pieces, brackets and other small assemblies to the appliance.
• Replaces stripped, corroded or broken screws that can cause loose parts or vibration noise.
• Helps restore proper alignment of doors, drawers or trim when a missing screw allows movement.
• Small appliance fastener sized for original mounting points—use the OEM screw whenever possible.

• Disconnect power and water before starting any repair.
• Start the screw by hand to avoid cross-threading; use the correct screwdriver or bit.
• Tighten snugly but avoid overtightening to prevent stripped threads or damaged plastic.

This screw is a direct-replacement fastener used to secure appliance panels and components. It provides a simple, reliable fix when a missing or damaged screw lets parts sit loose or vibrate. What it does:

• Secures service panels, trim pieces, brackets, or small components
• Restores proper fit and alignment to reduce rattling or movement
• Replaces stripped, missing, or corroded screws to maintain safe assembly
• Works wherever the OEM screw specification is required for reliable fastening

• Use the correct driver bit and turn gently to avoid stripping the head
• Ensure mating threads are clean and aligned before tightening
• Tighten until snug; do not over-torque to prevent damage to threads or parts
• Disconnect power before working near electrical components or controls

This air chamber directs and channels cold air inside the appliance to help maintain even temperatures. Replacing a damaged or cracked air chamber restores proper airflow for more consistent cooling and performance. What it does:

• Channels conditioned air from the evaporator into the cabinet to help even temperature distribution
• Prevents air leaks and redirects airflow to the correct compartments
• Can cause uneven cooling, warm spots, or frost buildup when cracked or broken
• Works with fans and ducts to maintain proper airflow balance

• One air chamber assembly

• Disconnect power to the appliance before beginning service
• Remove interior panels or shelves as needed to access the chamber; handle plastic tabs and clips carefully to avoid breakage
• Inspect adjoining ducts, seals, and mounting tabs; replace any damaged components to ensure a proper seal

Size: 6-20 x 0.312 inch.

This is a Phillips pan head machine screw commonly used to secure panels and components in appliances. It provides a reliable, low-profile head for flush fastening and easy Phillips-driver installation. What it does:

• Fastens trim, panels, or internal components where a pan head screw is required
• Designed for secure grip in metal or threaded inserts compatible with #10-16 threads
• Helps prevent loosening from vibration when installed to correct torque
• Often used in refrigeration and major appliance assemblies in limited quantities

• One Phillips pan head screw (#10-16 x 5/8")

• Use the correct #2 Phillips driver and steady pressure to avoid cam-out or stripping
• Do not overtighten; stop when snug to avoid damaging threads or mating parts
• Replace only with an identical thread size and head style to ensure fit
• Wear safety glasses when working around sharp sheet metal and springs

No.8 pan head `10 - 10b x 0.50 `cr/sq drive

This suspension spring supports the washer tub and helps stabilize the drum during spin cycles to reduce vibration and noise. Replaces a worn or broken tub spring to restore smoother operation. What it does

• Holds and stabilizes the inner tub assembly to limit excessive movement during spins
• Helps reduce vibration and rattling that can occur from a loose or broken spring
• Prevents tub misalignment that can cause rubbing or noise
• Works with the washer's suspension system to maintain proper spin balance

• One suspension (tub) spring as shown

• Disconnect power and water supply before starting any repairs
• Springs are under tension; use caution and proper tools to remove/install
• Inspect other suspension components (shocks/rods, mounts) and replace if worn

This mounting bracket secures its associated component inside your appliance, keeping it properly positioned during operation. Replacing a bent or broken bracket helps stop rattling or vibration and restores stable, reliable performance.

• Provides a rigid mounting point to the appliance frame or assembly
• Maintains correct position and alignment of the attached component
• Helps reduce vibration and operational noise
• Common failure signs: cracks, bending, stripped holes, or the part no longer stays secured

• Disconnect power before servicing; if working on a washer, also shut off water supply
• Note the original orientation and hardware locations; transfer any clips or grommets from the old bracket
• Reinstall using existing screws and tighten evenly—do not overtighten