Eigd50liwo Parts

This idler spring attaches to the idler arm to keep the drive belt properly tensioned, preventing slip and chatter. Replacing a weak or broken spring restores steady rotation and helps reduce noise and belt wear.

• Maintains correct belt tension by pulling the idler arm into position
• Helps prevent belt slippage, squealing/chirping, and premature belt wear
• A failed spring can cause no or intermittent rotation and the belt coming off
• Typical signs include a loose belt, off-track belt, or rhythmic squeak from the base

• Disconnect power before servicing; if working on a gas appliance, shut off the gas supply
• Access the idler assembly; note belt routing before removal
• Relieve belt tension, then move the idler arm to remove and replace the spring on the same mounting holes
• After reassembly, rotate by hand to verify smooth belt tracking before test

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

Replace a failed thermistor with this factory temperature sensor. It monitors temperature and feeds that data to the control, helping the appliance regulate heat and run cycles correctly. A faulty sensor can cause temperature-related performance issues.

• Senses temperature and sends a resistance signal to the control board for regulation
• Helps maintain proper heating/temperature during operation
• Failure may cause no heat or overheating, erratic or extended cycles, or temperature/sensor error codes
• Replace when sensor is open/shorted or readings are out of range per service diagnostics

• Disconnect power before servicing; if applicable, also shut off water or gas supply
• Access the sensor, unplug the wire connector, and remove any mounting screw/clip
• Install the new sensor; transfer any bracket/seal from the original and route wiring away from hot or moving parts
• Run a diagnostic or test cycle after replacement to confirm normal operation

This metric machine screw features an M5 x 0.8 thread used to secure panels and assemblies inside your appliance. Replacing missing or damaged hardware restores a tight, rattle-free fit and helps maintain proper alignment of parts.

• Fastens appliance components using an M5 x 0.8 machine-thread
• Replaces missing, loose, or stripped screws
• Helps reduce vibration and rattling noises
• Maintains correct alignment of brackets, panels, or internal assemblies

• Disconnect power before servicing; if working near water connections, shut off the supply.
• Match thread and length to the original screw and replace in the same location.
• Start threading by hand to avoid cross-threading; use the correct driver and do not overtighten.
• Reinstall any original washers or lock hardware used with the screw.

The Motor Mounting Clamp is an OEM part for Frigidaire dryers. This clamp secures the motor in place within the dryer, ensuring it operates smoothly and remains stable during the drying cycles. The motor mounting clamp is essential for maintaining the proper alignment and function of the dryer motor.

Over time, the motor mounting clamp can become worn out or damaged due to constant vibration and movement. Accidental impacts or mishandling during maintenance can also cause the clamp to fail, leading to motor misalignment or instability.

Symptoms of a bad motor mounting clamp include:

• Excessive noise or vibration during the drying cycle
• Motor shifting or moving within the dryer
• Reduced drying efficiency
• The dryer not starting or stopping abruptly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This moisture sensor monitors dampness inside the dryer drum and signals the control when fabrics are dry, helping automatic cycles end on time and avoid overdrying. Replacing a failed sensor can restore consistent Auto Dry performance and cycle times. What it does:

• Detects moisture level via conductivity across the sensor surfaces inside the drum
• Sends feedback to the control so Auto Dry cycles advance and stop correctly
• Helps prevent overdrying and underdrying in sensor-based cycles
• Common symptoms of a faulty sensor may include: auto cycles ending too soon or running too long, clothes remaining damp, or the dryer staying on "Sensing" while timed cycles still work

• 1 moisture sensor

• Disconnect power and, if applicable, shut off gas before servicing
• Access the sensor at the front bulkhead/lint housing area; remove front panel as needed per model
• Transfer connectors and route wiring exactly as original; secure the sensor firmly
• Clean the sensor contact surfaces with rubbing alcohol; residue from dryer sheets or fabric softeners can affect readings

This gasket forms a tight seal between mating components in your appliance, helping contain water, air, or heat as designed. Replacing a worn gasket restores proper sealing and helps prevent leaks, performance loss, and residue buildup. What it does:

• Creates a compressible seal between two parts to prevent leakage and maintain proper airflow or water containment
• Helps reduce rattles and wear at the joint by cushioning the connection
• Supports efficiency and consistent performance by keeping the system properly sealed
• Common symptoms of failure: visible cracks/tears or flattening, leakage at the joint, heat or moisture escaping, or persistent odors near the seal

• 1 gasket

• Disconnect power; shut off water supply before servicing
• Note the gasket's orientation and take reference photos during disassembly
• Remove the old gasket and thoroughly clean mating surfaces of residue or debris
• Seat the new gasket evenly without stretching; reassemble and test for a proper seal

The Support Roller Washer is an OEM part for Frigidaire dryers, designed to ensure the smooth and stable operation of the dryer drum. Positioned between the support roller and the shaft, this washer plays a critical role in reducing friction and wear, allowing the drum to rotate smoothly and quietly.

Causes of these symptoms often stem from normal wear and tear, which can lead to the degradation of the washer over time.  

Symptoms of a bad Dryer Support Roller Washer include:

• Unusual noises, such as squeaking or grinding, indicating increased friction during drum rotation
• The dryer drum appears to wobble or is misaligned during operation
• Increased vibration of the dryer, which can lead to wear on other components

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This genuine OEM replacement part is a gas valve assembly for dryers. The burner and gas valve assembly is a complete assembly that contains the burner that distributes the gas in a way that creates an even flame allowing for heat to be distributed properly to perform the dryer's essential functions. If the dryer is no longer drying clothes effectively, or heating properly, then it might be time for it to be replaced. Luckily repairing a gas valve assembly is an easy fix.To replace the burner and gas valve assembly, begin by shutting off power to the appliance. Next, pull the dryer away from the wall to gain access to the back panel. Remove the back panel and locate the gas valve assembly. Remove the mounting screws that hold it in place. After removing the screws use both hands to pull and release the old valve assembly. Set it off to the side and proceed to install the new one by refastening the screws that hold it in place.This replacement part is sold individually and is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand washers.

This burner assembly restores proper gas flame and heat in your dryer. It directs and mixes gas and air for clean ignition at the igniter, helping clothes dry efficiently and consistently.

• Provides the flame path and mixing chamber for gas ignition
• Helps resolve symptoms like no heat, intermittent heat, or very long dry times
• Can address issues where the burner won't ignite or the flame will not stay lit
• Designed to fit the factory burner mount and align with the igniter and flame sensor

• Disconnect power and shut off gas supply before servicing; allow the appliance to cool
• Access is typically from the front lower panel or burner compartment
• Transfer any reusable hardware from the original assembly if required
• After reassembly, restore gas and check all connections for leaks using a soapy water solution

This factory fastener secures appliance components and cabinet panels. Replacing a stripped, rusted, or missing screw restores a tight fit, reduces rattles and vibration, and keeps parts aligned for reliable operation. What it does:

• Fastens brackets, panels, and internal components to the cabinet/frame
• Helps maintain alignment and stability under vibration
• Direct replacement when the original is lost, corroded, or threads are damaged
• Common symptoms: loose or rattling panels, gaps/misalignment, or visibly missing hardware

• 1 screw

• Disconnect power; shut off gas/water if applicable before servicing
• Support the panel or component while removing/starting screws
• Match location and length to the original; start threads by hand to avoid cross-threading
• Tighten snugly—do not overtighten to prevent stripping

This small spacer fits on the idler assembly shaft to properly space and align the belt tensioner. Replacing a worn spacer helps keep the drive belt tracking correctly so the drum/tub runs smoothly and quietly. What it does:

• Spaces and centers the idler pulley on its shaft
• Helps maintain proper belt alignment and tension
• Can reduce squeaking or chirping from the idler area
• A worn or missing spacer may let the belt ride off, fray, or stop the drum/tub

• 1 idler spacer

• Disconnect power before servicing; let hot components cool
• Access the idler assembly per your model, relieve belt tension, and remove retaining hardware to slide off the pulley and old spacer
• Install the new spacer in the same location/orientation; reassemble and route the belt correctly
• Rotate the drum/tub by hand to verify smooth belt tracking before restoring power

This burner orifice meters gas to a range/cooktop burner through a calibrated opening. Replacing a clogged, damaged, or incorrect-size orifice helps restore proper flame height and clean, consistent combustion for reliable cooking performance.

• Regulates fuel flow to the burner via the precisely sized orifice opening
• Helps address weak/uneven flame, yellow or sooty flame, or delayed ignition
• Replaces stripped, blocked, or wrong-size orifice spud
• Size- and position-specific—match the stamped size and location

• Disconnect electrical power and shut off the gas supply before servicing
• Allow the cooktop to cool; remove grates, caps, and burner head to access the orifice holder
• Use the proper orifice/nut driver; do not overtighten or alter/enlarge the opening
• After reassembly, restore gas and leak-test with an approved solution; verify a stable blue flame and adjust air shutters if applicable

This duct routes air through the appliance's ventilation path to help maintain proper airflow and performance. Replace a cracked, warped, or obstructed duct to restore efficient air movement and reduce noise or uneven temperatures.

• Directs air along the intended passage between the fan/blower and internal compartments
• Helps prevent air leaks and bypass that can reduce efficiency
• Common symptoms include weak airflow, longer run times, rattling/vibration, or visible damage
• Replace if tabs are broken, the duct is deformed, or airflow is restricted by cracks/debris

• Disconnect power before servicing; allow hot components to cool
• Access typically requires removing a cover or panel—note screw lengths/locations
• Reuse existing fasteners and any gaskets/foam seals unless replacing them separately
• Ensure all mating surfaces seat fully to avoid air leaks before reassembly

Replacement striker for the refrigerator door latch that provides the catch point for the door to close securely. Restores proper door engagement to help maintain a tight seal and consistent internal temperature. What it does:

• Provides the catch point for the door latch so the door closes and stays latched
• Helps maintain an effective door seal to preserve cooling performance
• Common symptom: door won't stay closed, pops open, or fails to latch
• Also helps reduce drafts and noise caused by a misaligned latch

• Turn off power to the appliance before starting work
• Access the striker area, remove mounting fasteners, and replace with the new striker
• Align the striker so the latch engages smoothly; tighten screws securely
• Use care not to overtighten or strip mounting holes; replace damaged hardware as needed

This clip is a hose clamp used in select laundry appliances. It secures a hose connection to prevent leaks and keep water or air moving where it should, helping maintain reliable washer or dryer performance.

• Secures hose to its fitting to prevent leaks or disconnections
• Helps resolve issues like leaking at a hose joint, loose hose, or poor draining/airflow related to a slipped hose
• Durable spring-style clamp designed for repeatable tension
• Commonly used on internal washer or dryer hose connections

• Unplug the appliance and turn off water supply before service
• Have a towel or pan ready for residual water when removing hoses
• Use pliers to compress and slide the clamp; note original clamp position for reassembly
• Inspect hose ends for cracks; replace the hose if damaged before reinstalling the clamp