Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Replace your washer's housing cover if the original is cracked, broken, or missing. This protective cover installs on the exterior to shield internal components.
Usually ships within 4 - 14 days
Left apron bracket for washers. Secures the apron panel to the washer cabinet. Replace if cracked, broken, or missing to restore proper panel support.
Right side apron bracket for washers. Secures the apron panel to the washer cabinet. Replace if cracked, bent, or broken to restore proper panel support.
Washer leg and platform assembly that supports and levels your washer. Replace if the leg is cracked, broken, or the platform is damaged or missing.
This 1/4-20 screw secures the leg and platform assembly in your top-load washer. Replace missing or loose screws to restore proper balance.
OK kids, pay attention! This was my second attempt @ this repair. My first repair started leaking right away and had to be re-done about 6 months later. HERE IS THE PROBLEM!. In the video, you'll notice that (while putting it back together) when you put the square hole washer and split-ring over the shaft, they look to land atop the rubber seal, buy when you do this in real life, there is a gap between the seal and the washer. (This gap was close to a 1/4 inch). I THINK that the first time I... Read more
Replace your washer's touch pad control panel when buttons are unresponsive, cracked, or worn. This panel mounts on the console for cycle selection.
White right-hand console endcap for dryers. Replaces cracked, broken, or missing endcaps to restore the finished look of your control panel.
Replacement end cap for washer left-side assembly. Secures cabinet alignment and protects internal components. Needed when original is cracked or missing.
Self-leveling bracket for top-load washers. Mounts to the base to stabilize the unit. Replace if broken, bent, or missing to restore proper leveling.
Outer tub cover kit for washers. Includes bleach funnel, clamps, wire tie, and cap. Replace if cracked, broken, or missing components after repair work.
I looked up causes on the internet.I decided what parts I needed then found them on AppliancePartsPros.com. Their videos on how to replace their parts were very good, and customer service was great. My washer is running good now. Read more
Fix a washer that won't spin or agitates weakly with this motor and clutch kit. Solves pulsing motors and failed spin cycles. DIY repair takes 2-3 hours.
Handy Husband took off front of washing machine, unbolted motor then I held motor in place while he bolted on new one.He had to connect new wire harness.One wire was different color..orange instead of white with red stripe.He wrapped old hanging wires to steel bar supporting drum and new wire harness attached to inside where original used to be.He put on the new belt as well since old one was a bit old.He needed a phillips, metric tools..sockets, wrenches, wire cutters,a crimper, pliers and it... Read more
Converts older 3-piece washer support apron to one-piece design. Replaces sagging, bent, or broken apron brackets that cause motor clearance issues.
Installed GE # WH49X20925 Rod Support Sub-Frame, a factory specified upgrade. As a Design Engineer I would categorize this "fix" as an "Engineering Correction" a.k.a. a classic designer "screw-up". The Appliance Chassis was collapsing and required significant straightening before we could even begin the new perimeter frame install. Shame on GE! Otherwise a fine Family Unit being well abused. Read more
This ATC wiring harness connects the appliance's ATC control to the wiring harness, restoring reliable electrical connections for temperature/controls. It's a direct-fit replacement that helps resolve intermittent power or control failures caused by damaged wiring. What it does
Replacement plug insert for washer control panels and cabinet surfaces. Snaps into pre-drilled holes to cover openings or secure components. Needed when original plug is missing, cracked, or broken.
Fix washer overfilling or underfilling issues with a new pressure switch. Controls water levels by sensing tub pressure. Moderate DIY repair.
Conduit hose for top-load washers. Protects wiring connections inside the cabinet. Replace if cracked, split, or damaged to restore proper coverage.