Ffbd2406ns1a Parts

This thermistor is the dishwasher's temperature sensor. It reports water temperature to the control so the heater and cycle timing are managed correctly, helping restore reliable wash performance and more consistent drying.

• Monitors water temperature in the tub/sump and sends readings to the control board
• Helps the control regulate heater operation and determine cycle progress/timing
• Failure can result in no heat or poor drying
• May cause unusually long/short cycles or temperature-related fault codes

• Disconnect power at the breaker and shut off the water supply before servicing
• Access is typically from the toe-kick/base area or sump; remove the lower access panel as needed
• Release the locking tab/clip, remove the sensor, and ensure the existing seal/O-ring is properly seated; install the new sensor fully to prevent leaks
• Reconnect the wire harness, restore power, and run a test cycle to check for leaks and proper heating

This Shield is a protective cover used in select appliances. It helps guard nearby components and guide airflow or heat as designed, restoring proper protection when the original shield is cracked, warped, damaged, or missing.

• Acts as a barrier/deflector to protect components from heat, moisture, grease, or debris as designed for your model
• Helps maintain intended airflow, heat path, or splash control inside the appliance
• Replace if the shield is cracked, warped, burned, broken, or missing
• Symptoms can include visible damage, scorched or discolored areas near the shield, rattling/vibration, or exposed areas that were previously covered

• Disconnect power before servicing; also shut off gas
• Wear gloves—edges can be sharp on metal shields
• Reuse original screws/clips unless your model provides replacements
• Seat the shield flat and do not overtighten fasteners

This door gasket is the flexible rubber seal that closes the refrigerator door, helping keep cold air in and reduce energy loss. Replacing a worn or torn gasket restores a tight seal and helps the appliance maintain proper temperature. What it does:

• Seals the cabinet to keep cold air inside and warm air out
• Helps maintain consistent fridge/freezer temperature and efficiency
• Reduces frosting and moisture buildup caused by leaks
• Commonly needed when the seal is cracked, torn, warped, or no longer mates flush with the cabinet

• One replacement door gasket

• Clean the door flange and gasket mounting area before installing to ensure a proper seal
• Inspect for mounting clips or retainer channel; follow appliance-specific alignment steps for a snug fit
• Warm the gasket slightly (per OEM guidance) if needed to ease installation — avoid open flames or excessive heat

A replacement bearing that supports the dryer drum and restores smoother, quieter rotation. Replaces a worn or damaged bearing to help reduce noise and prevent excess drum play. What it does

• Provides a low-friction mounting point for the drum shaft to rotate smoothly
• Keeps the drum aligned and reduces wobble during operation
• Helps prevent metal-on-metal contact that causes grinding or rumbling noises
• Can reduce strain on the motor and belt by restoring proper drum support

• Disconnect power before beginning any disassembly
• Replacement typically requires removing panels and the drum;
• Inspect surrounding seals, shafts, and mounting hardware and replace if worn

This outer refrigerator door restores the appliance's exterior and helps maintain proper sealing and temperature control. It replaces a cracked, dented, or damaged door to improve appearance and function. What it does

• Replaces a damaged outer door panel so the fridge can close properly and look like new
• Helps maintain an effective seal when used with an intact gasket, reducing cold air loss
• Stops drafts and visible damage that can lead to higher energy use or interior moisture
• Works with existing hinges and trim when the correct hardware is transferred

• Disconnect power to the appliance before starting and remove food from door shelves as needed
• Transfer existing hinge assemblies, handles, trim, and gasket to the new door unless this part specifically includes them
• Use caution when lifting and aligning the door to avoid chipping paint or damaging the hinge pins
• If you see missing or damaged hardware, get the required screws/hinges separately.

This control panel overlay is the thin printed decal that covers the appliance's front control area, restoring labeled buttons and a clean, finished appearance for easier operation and improved aesthetics. What it does:

• Replaces a worn, faded, or damaged control panel decal so button labels and markings are readable
• Protects the underlying control surface from spills, dirt, and everyday wear
• Restores original look and helps ensure users can correctly identify controls
• Useful when the panel graphics are scratched, discolored, or peeling

• One control panel overlay

• Disconnect power to the appliance before beginning any work
• Remove the control panel or trim as needed to access the old overlay per your model's service instructions
• Clean the surface thoroughly and align the overlay carefully; avoid stretching or trapping air bubbles
• If adhesive is used, press firmly and allow any recommended set time before reassembling and restoring power

This replacement brace is a support bracket that helps secure and stabilize appliance panels and components, restoring proper alignment and reducing vibration. Designed for direct fit where the original bracket is damaged or missing. What it does:

• Provides structural support to panels, frames, or assemblies to maintain alignment and fit
• Secures components to prevent wobbling, rattling, or movement during operation
• Helps restore proper door or panel fit when a broken or bent bracket causes misalignment
• Reduces noise caused by loose or unsupported parts

• One replacement brace

• Disconnect power or unplug the appliance before starting any work
• Use the original screw locations and hardware where possible; save any reusable fasteners
• Inspect surrounding panels and mounting points for additional damage before reassembly