Ffbd240ns0a Parts

This bezel is a trim piece for Frigidaire dishwashers that finishes and protects an opening on the door/control panel, helping the mating component sit properly while restoring a clean, factory look.

• Frames and protects the panel opening for a control or latch component
• Helps keep the mating part aligned and seated correctly
• Covers raw edges and gaps to reduce wear and debris buildup
• Common symptoms: broken or missing trim, loose/wobbly bezel, cracked retaining tabs, cosmetic damage

• Disconnect power to the dishwasher before servicing
• Remove the control knob or latch handle to access the bezel
• Release the bezel's retaining tabs/clips and lift it out from the panel
• Align the new bezel and snap/secure it into place; reinstall any removed parts and test operation

This thermistor is the dishwasher's temperature sensor. It reports water temperature to the control so the heater and cycle timing are managed correctly, helping restore reliable wash performance and more consistent drying.

• Monitors water temperature in the tub/sump and sends readings to the control board
• Helps the control regulate heater operation and determine cycle progress/timing
• Failure can result in no heat or poor drying
• May cause unusually long/short cycles or temperature-related fault codes

• Disconnect power at the breaker and shut off the water supply before servicing
• Access is typically from the toe-kick/base area or sump; remove the lower access panel as needed
• Release the locking tab/clip, remove the sensor, and ensure the existing seal/O-ring is properly seated; install the new sensor fully to prevent leaks
• Reconnect the wire harness, restore power, and run a test cycle to check for leaks and proper heating

This Shield is a protective cover used in select appliances. It helps guard nearby components and guide airflow or heat as designed, restoring proper protection when the original shield is cracked, warped, damaged, or missing.

• Acts as a barrier/deflector to protect components from heat, moisture, grease, or debris as designed for your model
• Helps maintain intended airflow, heat path, or splash control inside the appliance
• Replace if the shield is cracked, warped, burned, broken, or missing
• Symptoms can include visible damage, scorched or discolored areas near the shield, rattling/vibration, or exposed areas that were previously covered

• Disconnect power before servicing; also shut off gas
• Wear gloves—edges can be sharp on metal shields
• Reuse original screws/clips unless your model provides replacements
• Seat the shield flat and do not overtighten fasteners

This kickplate (toe plate) replaces the lower front trim on compatible refrigerators to restore appearance and protect the cabinet base from scuffs and drafts. Durable sheet-metal construction keeps the front edge looking clean. What it does:

• Covers and protects the refrigerator's lower front area from kicks, scuffs and dirt.
• Restores a secure trim piece when the original is bent, dented or loose.
• Helps reduce visible gaps at the cabinet base for a neater fit.
• Improves appliance appearance after damage or during refurbishment.

• Disconnect power to the appliance or follow the manufacturer's safety guidance before beginning work.
• Remove the old kickplate by loosening the retaining screws or clips; lift out and set aside.
• Align the replacement plate, engage any clips or tabs, and reinstall screws; avoid overtightening.

This door gasket is the flexible rubber seal that closes the refrigerator door, helping keep cold air in and reduce energy loss. Replacing a worn or torn gasket restores a tight seal and helps the appliance maintain proper temperature. What it does:

• Seals the cabinet to keep cold air inside and warm air out
• Helps maintain consistent fridge/freezer temperature and efficiency
• Reduces frosting and moisture buildup caused by leaks
• Commonly needed when the seal is cracked, torn, warped, or no longer mates flush with the cabinet

• One replacement door gasket

• Clean the door flange and gasket mounting area before installing to ensure a proper seal
• Inspect for mounting clips or retainer channel; follow appliance-specific alignment steps for a snug fit
• Warm the gasket slightly (per OEM guidance) if needed to ease installation — avoid open flames or excessive heat

A replacement bearing that supports the dryer drum and restores smoother, quieter rotation. Replaces a worn or damaged bearing to help reduce noise and prevent excess drum play. What it does

• Provides a low-friction mounting point for the drum shaft to rotate smoothly
• Keeps the drum aligned and reduces wobble during operation
• Helps prevent metal-on-metal contact that causes grinding or rumbling noises
• Can reduce strain on the motor and belt by restoring proper drum support

• Disconnect power before beginning any disassembly
• Replacement typically requires removing panels and the drum;
• Inspect surrounding seals, shafts, and mounting hardware and replace if worn

This outer refrigerator door restores the appliance's exterior and helps maintain proper sealing and temperature control. It replaces a cracked, dented, or damaged door to improve appearance and function. What it does

• Replaces a damaged outer door panel so the fridge can close properly and look like new
• Helps maintain an effective seal when used with an intact gasket, reducing cold air loss
• Stops drafts and visible damage that can lead to higher energy use or interior moisture
• Works with existing hinges and trim when the correct hardware is transferred

• Disconnect power to the appliance before starting and remove food from door shelves as needed
• Transfer existing hinge assemblies, handles, trim, and gasket to the new door unless this part specifically includes them
• Use caution when lifting and aligning the door to avoid chipping paint or damaging the hinge pins
• If you see missing or damaged hardware, get the required screws/hinges separately.

This genuine replacement screw secures appliance panels and components so assemblies stay tight and stable. It's a simple, direct fix when a missing or damaged screw causes loose trim, rattling, or misaligned parts. What it does:

• Fastens panels, brackets, and trim to restore proper alignment and stability
• Stops rattling or vibration caused by loose hardware
• Replaces stripped or corroded screws to ensure secure connections
• Works wherever the OEM screw is specified in the appliance

• Use the matching driver and proper torque to avoid stripping the head or threads
• Replace only with the exact OEM screw to maintain fit and function
• Disconnect power before accessing internal components; follow appliance safety instructions
• Replace all like-for-like for best results

Color: White

Color: Black