Fffu06m1tw Parts

The Air Tower is an OEM part for Frigidaire refrigerators. The cover helps circulate cold air throughout the freezer while also protecting internal components from damage or debris.

Over time, freezer air tower covers can become damaged or discolored due to repeated exposure to cold temperatures and humidity inside the freezer. Signs of a bad cover include cracks, holes, or missing pieces that compromise its ability to properly ventilate the freezer.

Symptoms of a bad freezer air tower cover include:

• Inefficient air circulation leading to warmer freezer temperatures
• Formation of ice buildup around the evaporator coil
• Exposure of internal freezer components to damage or contamination

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Replacement door magnet that helps the refrigerator or freezer door stay closed for a tighter seal and more consistent cooling. Restores magnetic hold so doors close reliably and reduce warm spots. What it does

• Provides magnetic hold for the door liner so the door stays shut during normal use
• Helps maintain the gasket engagement to preserve internal temperature
• Common symptom: door not staying closed, food warming, or frost build-up near the door
• Used in door/gasket assembly where magnets secure the seal

• Turn off power to the appliance or unplug before removing door trim or accessing internal components
• Remove door liner or gasket per service instructions to access and replace the magnet; keep fasteners and seals intact
• Press or seat magnet into its channel or mounting location; use the OEM fastener or adhesive method specified by the manufacturer

This gasket creates a tight seal between appliance components to prevent leaks and maintain efficient performance. Replacing a worn or damaged gasket restores proper sealing, helping stop moisture or air from escaping and reducing related issues. What it does

• Forms a compressible barrier between mating surfaces to block water, air, or debris
• Helps maintain correct temperatures and/or contain water during operation
• Addresses symptoms like leaks, moisture or frost buildup, and poor sealing
• Replace if the original is cracked, flattened, torn, or misshapen

• Includes 1 gasket

• Disconnect power and shut off water before servicing
• Remove the old gasket and clean mating surfaces thoroughly; avoid sharp tools that could mar the seal area
• Seat the new gasket evenly without stretching; ensure it's fully seated in its groove or channel
• Reassemble and test for proper seal and leaks before returning to service

This replacement screw secures panels, brackets, or internal components in select Frigidaire-made refrigerators and freezers. Use it to replace missing or stripped hardware and restore a secure fit to help reduce vibration and noise.

• Fastens appliance panels, brackets, and internal components
• Helps prevent vibration, rattling, or looseness from missing hardware
• Reliable fix when the original screw is missing, damaged, or stripped
• Designed for proper fit in the original threaded location(s) specified for this part number

• Disconnect power to the appliance before servicing
• Align parts and start the screw by hand to avoid cross-threading
• Tighten snugly; do not overtighten, especially into plastic components
• Reuse any original washers or clips if present and in good condition

The Freezer Shelf is an OEM part for Frigidaire refrigerators. It provides storage and organization within the freezer compartment. This shelf can be positioned at different heights to accommodate varying package sizes. 

Symptoms of a bad freezer shelf include:

• Cracks or damage allowing stored items to fall through
• Difficulty removing or repositioning the shelf 
• Warping or bending under weight

Causes of a bad shelf can include wear and tear over time from repeated loading and unloading of items, as well as potential stresses or shocks from accidental impacts.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This support is a small mounting bracket used inside the appliance to hold an interior component, such as a shelf or basket. Replacing a cracked or missing support restores a secure, level fit and helps prevent wobbling or dropping.

• Provides a stable mounting point for a shelf, basket, rail, or panel
• Keeps interior components aligned and level
• Common symptoms: shelf/basket tilts, won't seat, or falls; visible cracks or missing support
• Replace if broken, deformed, or worn to restore proper fit

• Disconnect power and clear the work area before starting
• Remove the affected shelf/basket/panel to access the mounting point
• Release the damaged support (snap tabs or remove screw), align, and install the new support
• Reinstall the component and verify it sits level and secure

This inverter is the compressor drive module that controls variable-speed operation to help your refrigerator cool efficiently and quietly. It replaces a failed drive unit so the compressor can respond to temperature controls. What it does

• Converts incoming power and controls compressor motor speed for proper cooling
• Restores variable-speed compressor operation when the drive has failed
• Resolves symptoms like reduced or no cooling, long run cycles, or inverter-related fault codes
• Works with the fridge's control system to regulate compressor performance

• One inverter (compressor drive) module

• Disconnect power to the appliance before starting; verify the unit is completely de-energized
• Handle the module carefully and avoid contact with exposed circuitry or connectors
• Match connector pins and mounting points; secure all electrical connections

The EVAPORATOR INSULATOR is an OEM part for Frigidaire refrigerators. It is a heat-resistant insulating pad or wrap that surrounds the evaporator coils. The insulator works to retain cool air and prevent warmer air from entering the refrigerated compartment.  

Causes of a bad insulator can include deterioration or breakdown of insulating properties over time due to aging materials. Cracks, holes, or compressed sections of the insulator result in reduced insulation performance.

Symptoms of a bad evaporator insulator include:

• Inconsistently cool or warmer fridge temperatures 
• Frost or ice buildup on evaporator coils or surrounding areas
• Higher than normal electric bills from inefficient cooling
• Warm or cold spots inside refrigerator shelves and compartments

This OEM Frigidaire replacement insulator is compatible with some Kitchenaid, Electrolux, Gibson, Kelvinator, and Kenmore side-by-side refrigerator models. 

This screw set replaces missing, stripped, or damaged fasteners to secure components in your appliance. Restoring proper hardware helps keep parts aligned, reduces rattling, and maintains a solid, reliable fit. What it does:

• Fastens panels, brackets, and other components as specified by the manufacturer
• Replaces worn or lost screws to restore secure attachment points
• Helps resolve loose handles or panels, vibration/rattling noises, and shifting parts
• Supports correct alignment for dependable operation

• Screw set as supplied by the manufacturer

• Disconnect power before servicing; wear cut-resistant gloves
• Support the part being fastened (door, panel, bracket) to prevent damage
• Start screws by hand to avoid cross-threading; tighten evenly and do not overtighten
• Replace one screw at a time to maintain alignment

Made for use with refrigerators by several major manufacturers, this is a full compressor kit. It is an internal part that is tasked with moving refrigerant throughout the appliance. It also works by adding pressure to part of the circuit to heat up the refrigerant. This creates a high pressure, hot gas that is moved to the compressor to be cooled and used to keep the appliance at the appropriate temperature. If the compressor is damaged or broken, it can cause the refrigerator to start making loud noises. The compressor may turn on and off more frequently than expected, created overheating and improper cooling, and create clicking noises. If the compressor kit is damaged, it should be replaced. Turn off the circuit breaker or unplug the refrigerator. Pull out the refrigerator and take off the access plate. Let it cool down before the compressor is removed. Use the contents of the kit to replace the part before reassembling and turning the power back on.This is a genuine OEM replacement part that can be used with Frigidaire, Kenmore, Gibson, Westinghouse, Tappan, Crosley, Kelvinator, Universal, and Electrolux freezers and refrigerators. It is sold as an individual part.

The Socket is an OEM part for Frigidaire refrigerators. It is responsible for holding and connecting the light bulb in the refrigerator, allowing for proper lighting inside the appliance.

A bad light socket can be caused by electrical issues, physical damage, or wear and tear over time. Signs of a faulty light socket include a non-functional light bulb, flickering or dim lighting, or a loose connection.

Symptoms of a bad light socket can include:

• The refrigerator light not turning on 
• Intermittent flickering or dimming of the light
• Difficulty in installing or removing the light bulb
• Visible damage on the socket

Replace your malfunctioning light socket with this genuine OEM part to restore your refrigerator. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

The Potentiometer Retainer Clip is an OEM part for Frigidaire bottom-mount refrigerators. Located inside the ice maker assembly, this small clip firmly holds the potentiometer dial in position. The potentiometer regulates water temperature for producing quality ice cubes.

Potential causes of failure include normal wear from extended use in the refrigerator environment. Heat cycling during ice production may cause faster deterioration over time.

Symptoms of an improperly secured or damaged retainer clip include:

• Loose or faulty potentiometer preventing ice making  
• Water not dispensing at the proper temperature
• Inability to reliably produce clear, solid ice cubes
• Internal noises from components loosened without the clip

This retainer clip fits additional brands including Electrolux, Gibson and select Kenmore models.

This light socket securely holds the appliance bulb and provides the electrical connection to illuminate the compartment when the door is opened. Replacing a faulty socket restores interior lighting so you can easily see contents.

• Provides the electrical connection and physical mounting for the light bulb
• Common failure symptoms: light won't turn on, flickers, or only works when the bulb is jiggled
• Show signs of heat discoloration, loose terminals, or intermittent contact

• Unplug the appliance before service; power is off
• Allow the bulb and surrounding area to cool before handling
• Handle wiring carefully; transfer conductors to the new socket one at a time to maintain correct connections
• Do not exceed the bulb type/wattage specified on the appliance rating label

A small replacement mounting clip that secures interior trim or panels on select refrigerators, helping restore a snug fit and reduce loose, rattling parts. Fits where worn or broken clips allow trim to shift. What it does:

• Holds trim, panels or small components in place to prevent rattling and movement.
• Restores proper alignment of affected panels so edges sit flush and look finished.
• Simple mechanical fastening — replaces brittle or broken clips that no longer grip.
• Helps reduce noise caused by loose interior parts during normal operation.

• Always unplug the appliance or switch off power at the breaker before servicing.
• Remove the affected trim or panel per manufacturer instructions to access the clip location.
• Press the clip into the mating slot or post until it seats securely; use a small tool if needed to avoid fingernail or surface damage.
• Inspect surrounding mounting surfaces for cracks or wear; damaged supports may require additional replacement parts.

This precision bearing supports a rotating component inside your appliance, reducing friction for smooth, reliable operation. Replacing a worn bearing can eliminate noise and restore proper movement in the affected assembly.

• Provides low-friction support for a rotating shaft or component
• Helps maintain alignment for smooth, quiet operation
• Common symptoms include squealing/grinding noises, wobble/play, or binding/seized rotation
• Excess drag can cause overheating or motor overload

• Disconnect power and shut off gas/water supplies as applicable before service
• Match orientation to the original and your model's diagram for placement
• Clean the shaft/bore and inspect mating parts; replace worn components; apply OEM-approved lubricant only if specified
• If press-fit is required, use proper drivers/press tools; do not hammer directly on the bearing

This is an authentic OEM freezer basket bumper sourced directly from the manufacturer for use on freezer baskets. Freezer basket bumpers are attached to the baskets to keep them from sliding around inside the freezer. If the bumper breaks, the basket will not stay in place, and the contents could shift or fall out. Freezer baskets create more storage room inside a freezer. These baskets are normally located on the bottom of the freezer, with freezer racks located above. Freezer baskets are ideal for storing smaller packages that might not stack well on the racks. Over time, normal wear and tear may cause the bumper to crack or break completely; if this happens, the bumper should be replaced. Remove the contents of the freezer basket. Remove the freezer basket from the freezer. Push the new bumper onto the freezer basket. Replace the contents of the basket and put it back into the freezer. This handle freezer basket is made of high-quality, white molded plastic. It is designed for use in freezers manufactured by Frigidaire, Kenmore, Gibson, and Electrolux.