Ffht1831qp2 Frigidaire/ Refrigerator Parts

This freezer temperature control assembly regulates cooling by monitoring cabinet temperature and switching the cooling system on and off to match your setting. Replace it if temperatures drift, the unit short-cycles or runs constantly, or the control stops responding. What it does:

• Senses freezer temperature and commands the cooling system to maintain your selected set point
• Provides user adjustment of freezer temperature via the control mechanism
• Helps restore consistent, reliable freezing performance
• Common failure symptoms include too warm or too cold temperatures, continuous running or no run, and an unresponsive temperature dial

• 1 freezer temperature control assembly

• Disconnect power before servicing
• Access the control housing; note wire/harness positions and component orientation for reassembly
• Transfer any reusable mounting parts from the original control as needed; secure wiring away from moving parts
• Set the control to a mid-range setting and allow up to 24 hours for temperatures to stabilize after replacement

This defrost pan collects water from the refrigerator's automatic defrost cycle and sits over warm components so it can evaporate safely. Replace a cracked or deformed pan to help prevent floor puddles and musty odors. What it does:

• Collects defrost condensate and allows it to evaporate in the machine compartment
• Helps keep floors dry by managing defrost water
• Replace if the pan is cracked, warped, leaking, or missing
• Common symptoms include water under the refrigerator, recurring puddles, or musty odors

• 1 defrost drain pan

• Disconnect power and pull the refrigerator away from the wall before servicing
• Remove the rear access panel to reach the drain pan
• Slide out the old pan carefully and empty any water; reuse any original supports/brackets if present
• Set the new pan on its supports, ensure the drain outlet/tube drips into the pan, reinstall the panel, restore power, and check for leaks

This aluminum strap secures the defrost heater firmly against the evaporator coil to maintain proper contact during defrost. Correct contact improves heat transfer so frost melts evenly and helps prevent recurring ice buildup on the evaporator.

• Secures the defrost heater to the evaporator for proper contact and heat transfer
• Promotes complete, even defrosting across the evaporator coil
• Helps reduce repeat frost/ice accumulation caused by a shifted or loose heater
• Typical clues include a loose heater, uneven frost pattern, or rattling near the evaporator

• Disconnect power and allow ice to melt before accessing the evaporator
• Use care around sharp fins and fragile refrigerant tubing; do not puncture or deform the coil
• Position the heater per your model's parts diagram and tighten the strap for firm, even contact
• Verify wiring is routed clear of the fan and moving parts before reassembly

This center hinge bracket mounts to the refrigerator cabinet at the middle hinge location. It provides a secure mounting point for the hinge, keeping the door aligned for smooth operation and a reliable gasket seal.

• Secures the middle hinge to the cabinet to support the door
• Helps maintain alignment for smooth opening/closing and proper gasket contact
• Common fix for a sagging, rubbing, or misaligned door
• Replaces a bent, cracked, or worn bracket

• Disconnect power and support the door before loosening center hinge fasteners
• Remove the old bracket and transfer the hinge and any spacers/washers to the new bracket if applicable
• Install the new bracket, align the door, then tighten screws securely
• Verify smooth swing and full gasket contact; readjust if needed

Color: White

This compressor mounting clip secures the compressor to its chassis to reduce movement and noise for reliable operation. It replaces worn or broken clips that allow the compressor to shift during use. What it does:

• Holds the compressor in place on the mounting bracket to prevent shifting
• Reduces vibration and rattling noises caused by a loose mount
• Helps maintain proper compressor alignment for steady operation
• Useful when a cracked or bent clip no longer secures the compressor

• Disconnect power to the appliance before accessing compressor area
• Inspect surrounding mounts and rubber isolators; replace if damaged
• Secure clip fully so compressor is held without forcing or misaligning components

Color: White

This seal kit replaces worn sealing material in your appliance to restore a tight, reliable barrier. A fresh seal helps stop leaks and drafts, reduces noise, and supports proper temperature and moisture control.

• Creates a secure seal between mating surfaces or components
• Helps prevent air or water leaks around the sealed area
• Can reduce vibration noise from gaps or loose fits
• Supports stable temperatures and overall efficiency
• Common signs include visible gaps, cracking, flattening, or persistent leakage

• Disconnect power (and water or gas, if applicable) before servicing
• Remove the old seal and thoroughly clean mating surfaces of residue
• Test-fit for length/orientation; trim only if instructed by the manufacturer
• Press into place evenly; if adhesive-backed or cement is used, allow proper set time before use and check for leaks

This drain trough directs defrost water from the evaporator to the refrigerator drain, helping prevent pooling, leaks and ice build-up in the fresh-food compartment. A correct trough keeps defrost water flowing and reduces odors or floor damage. What it does:

• Channels defrost/condensate water from the evaporator to the drain system
• Prevents water pooling under shelves or in the crisper area
• Reduces ice buildup and attendant leaks when the drain path is clear
• Replace if cracked, warped, or if water is collecting where it shouldn't

• Disconnect power to the appliance before servicing
• Remove interior shelves/drawers as needed to access the trough
• Clean the drain channel and clear any debris before installing the new trough
• Make sure the trough is fully seated and aligned so water drains properly; follow OEM fastener/placement points

This replacement cover restores a clean, finished look and protects the designated compartment in your refrigerator. Replacing a cracked or missing cover helps keep internal components shielded and secure so the unit operates as intended. What it does

• Shields internal components and wiring from damage and debris
• Helps maintain proper airflow or routing where used as a duct/guard
• Restores secure fit when the original cover is cracked, warped, or missing
• Common symptoms: broken tabs, cracks, rattling/vibration, loose or missing cover

• 1 cover

• Disconnect power; turn off water supply if working near water/ice components
• Remove any screws or release tabs; retain and reuse original fasteners
• Align tabs and seat fully before tightening; do not overtighten to avoid cracking
• Plastics can be brittle when cold—allow the part/area to warm to room temperature

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required

This OEM ring is a small hardware component used within the appliance assembly to secure or support a mating part, helping restore proper fit, alignment, and dependable operation when the original ring is worn, damaged, or missing.

• Holds a component in position within the assembly to prevent unwanted movement
• Helps maintain alignment and reduce wobble, vibration, or rubbing
• Common signs of a failing ring include looseness, rattling noises, or parts drifting out of place
• Replacing a damaged ring can restore smooth, consistent operation of the related mechanism

• Disconnect power (and shut off gas/water if applicable) before servicing
• Carefully remove the old ring and seat the new ring fully in its groove or mounting point
• After installation, verify the related part is properly retained and moves or operates freely as intended

Replacement refrigerator interior light socket that secures the interior lamp and connects it to the cabinet wiring, restoring reliable interior illumination. Use this when the light fails to come on, flickers, or the bulb sits loosely. What it does:

• Holds the interior lamp and provides the electrical connection for lighting
• Restores consistent contact to prevent flicker or intermittent operation
• Common repair for a light that won't turn on or a bulb that won't stay seated
• Fits into the interior housing to maintain proper lamp alignment

• Disconnect power to the appliance before inspecting or replacing the socket
• Remove the bulb before swapping the socket to avoid breakage or shock
• Inspect wiring and connectors for damage; replace if wiring is frayed
• Avoid getting the socket wet and use only the correct bulb type and wattage specified by the appliance

A replacement name plate that restores the appliance's factory identification label so model and serial information are legible for service and parts lookup. Helps maintain the appliance's appearance and accurate identification. What it does:

• Provides the factory identification area showing model/serial and manufacturer data for parts lookup and service.
• Use when the original label is missing, scratched, faded, or peeling and no longer readable.
• Restores exterior appearance where the original name plate has cosmetic damage.

• Clean and dry the mounting surface before installing; remove old adhesive residue if present.
• Align carefully and press firmly; some installations may require removal of trim or a cover.
• Use appropriate tools and avoid sharp solvents that could damage surrounding surfaces.

Here is a replacement shelf support grommet that is used in freezers and refrigerators. The grommets are used to provide stability for the shelves in the refrigerator. If they are broken or missing, the shelves will not sit correctly, and owners won't be able to put anything onto the shelves. A replacement grommet should slide into place, but may need to be gently tapped to ensure a proper seal is made.The shelf support grommet is for use with certain refrigerator models from Frigidaire, Kenmore, Gibson, and Crosley. This is a genuine OEM replacement part that was sourced directly from the manufacturer. It is important to note that the grommets are sold individually. If more than one is needed, owners will need to order multiple.