Fftr1821qwo Parts

This wiring harness routes electrical power/signals between refrigerator components. Replacing a damaged harness helps restore reliable connections so fans, sensors, lights, or the icemaker receive proper power and communication.

• Connects internal refrigerator components to the main wiring circuit
• Can help when there are intermittent power issues to fans, lights, or icemaker
• Designed to fit specific layouts; match connectors to your original for compatibility

• Disconnect power before servicing to avoid electrical shock
• Take photos of existing connector locations to ensure correct reassembly
• Handle connectors by the housings; avoid pulling on wires
• If connectors don't seat easily, re-check orientation—do not force

This refrigerator grommet is a small sealing/cushioning insert used where a tube, wire, or component passes through the cabinet or mounts to a panel. It helps keep the opening sealed and protected for reliable operation.

• Seals and cushions an opening or mounting point in the refrigerator cabinet
• Helps prevent water leaks and warm-air infiltration that can lead to frost or moisture
• Reduces chafing, vibration, and wear on tubing or wiring
• Replace if the grommet is cracked, hardened, misshapen, or missing

• Unplug the refrigerator and, if applicable, shut off the water supply
• Access the grommet location by removing any cover or panel as needed
• Remove the old grommet, clean the opening, and press the new grommet fully into place; route the line/wire without kinks
• Restore power (and water, if used) and check for proper sealing and operation

This freezer temperature control assembly regulates cooling by monitoring cabinet temperature and switching the cooling system on and off to match your setting. Replace it if temperatures drift, the unit short-cycles or runs constantly, or the control stops responding. What it does:

• Senses freezer temperature and commands the cooling system to maintain your selected set point
• Provides user adjustment of freezer temperature via the control mechanism
• Helps restore consistent, reliable freezing performance
• Common failure symptoms include too warm or too cold temperatures, continuous running or no run, and an unresponsive temperature dial

• 1 freezer temperature control assembly

• Disconnect power before servicing
• Access the control housing; note wire/harness positions and component orientation for reassembly
• Transfer any reusable mounting parts from the original control as needed; secure wiring away from moving parts
• Set the control to a mid-range setting and allow up to 24 hours for temperatures to stabilize after replacement

Bottom air diffuser directs cold air into the refrigerator's lower cabinet to help maintain even temperatures and reduce warm spots. Replacing a damaged diffuser restores proper airflow and helps the fresh-food section cool more consistently. What it does:

• Redirects cold air from the cooling channel into the refrigerator's lower cabinet for balanced cooling.
• Helps reduce warm spots and uneven temperatures in the fresh-food area.
• A cracked, broken, or missing diffuser can lead to restricted airflow and inconsistent cabinet temperatures.
• Seats into the lower air channel and secures with factory tabs or fasteners; inspect mounting tabs for damage.

• Disconnect power to the appliance before performing any service.
• Remove shelves and drawers as needed for access; work carefully around evaporator/air channels.
• Gently release and re-seat plastic tabs or remove fasteners; avoid forcing parts to prevent breakage.
• If tabs are damaged, replace them or consider replacing adjacent vent components to ensure a secure fit.

This replacement water tube routes water within the refrigerator's internal water system. Installing a fresh, intact tube helps stop leaks and restores reliable water flow to the dispenser and ice maker. What it does:

• Carries water between components such as the inlet valve, reservoir, dispenser, and ice maker
• Maintains a sealed, kink-free path for proper flow and pressure
• Common signs of failure: leaks or puddling, weak or no dispenser flow, ice maker not filling, brittle or discolored tubing

• One tube

• Unplug the refrigerator and shut off the water supply before servicing
• Note the original routing; take photos to match length and path
• If trimming, cut ends square and fully seat into the existing push-to-connect or compression fittings
• Restore water and check all connections for leaks before powering the unit back on

This defrost pan collects water from the refrigerator's automatic defrost cycle and sits over warm components so it can evaporate safely. Replace a cracked or deformed pan to help prevent floor puddles and musty odors. What it does:

• Collects defrost condensate and allows it to evaporate in the machine compartment
• Helps keep floors dry by managing defrost water
• Replace if the pan is cracked, warped, leaking, or missing
• Common symptoms include water under the refrigerator, recurring puddles, or musty odors

• 1 defrost drain pan

• Disconnect power and pull the refrigerator away from the wall before servicing
• Remove the rear access panel to reach the drain pan
• Slide out the old pan carefully and empty any water; reuse any original supports/brackets if present
• Set the new pan on its supports, ensure the drain outlet/tube drips into the pan, reinstall the panel, restore power, and check for leaks

This aluminum strap secures the defrost heater firmly against the evaporator coil to maintain proper contact during defrost. Correct contact improves heat transfer so frost melts evenly and helps prevent recurring ice buildup on the evaporator.

• Secures the defrost heater to the evaporator for proper contact and heat transfer
• Promotes complete, even defrosting across the evaporator coil
• Helps reduce repeat frost/ice accumulation caused by a shifted or loose heater
• Typical clues include a loose heater, uneven frost pattern, or rattling near the evaporator

• Disconnect power and allow ice to melt before accessing the evaporator
• Use care around sharp fins and fragile refrigerant tubing; do not puncture or deform the coil
• Position the heater per your model's parts diagram and tighten the strap for firm, even contact
• Verify wiring is routed clear of the fan and moving parts before reassembly

The Power Cord is an OEM replacement part for Frigidaire refrigerators. As the lifeline connecting the appliance to a wall outlet, this cord safely delivers necessary voltage to operate refrigerator systems. 

Potential causes for needing a new power cord include exposure to cuts, abrasions or rodent damage over time in the storage area. Repeated bending stress during installation or removal can also wear out plastic insulation faster.

Symptoms of a faulty power cord include: 

• Refrigerator fails to power on at all
• Flickering lights or inconsistent runs of the compressor  
• Shock, buzzing or humming sounds coming from the cord
• Bare copper wire showing through damaged insulation

This power cord also fits some Electrolux and Gibson refrigerators.

This plug covers the small factory test opening on an appliance cabinet or liner. Replacing a missing or damaged plug helps close the opening to maintain a better seal and restore a clean, finished appearance.

• Seals the factory test opening in the cabinet/panel
• Helps limit air and moisture infiltration through the hole
• Reduces condensation or frost forming around the opening
• Restores a finished look when the original cap is missing or damaged

• Disconnect power before servicing the appliance
• Clean and dry the opening area for proper fit
• Align and press the plug in by hand until it sits flush—do not force or enlarge the hole
• Avoid sharp tools or sealants that could damage the liner or insulation

Replacement air purifier assembly that restores the refrigerator's internal air-care function and helps reduce persistent odors. Installs in the fresh-food compartment to restore the appliance's odor-control and air-freshening performance. What it does:

• Houses the refrigerator's air-purifying module to help trap and reduce odors and airborne contaminants.
• Restores air-care performance when the original purifier is damaged, clogged, or missing.
• Works as part of the fridge's internal air circulation and odor-control system.

• One air purifier assembly

• Disconnect power to the appliance before accessing internal panels or components.
• Remove interior panels or shelves as required to reach the purifier; keep parts and fasteners organized.
• Handle the assembly carefully to avoid damage; use basic hand tools.

This center hinge bracket mounts to the refrigerator cabinet at the middle hinge location. It provides a secure mounting point for the hinge, keeping the door aligned for smooth operation and a reliable gasket seal.

• Secures the middle hinge to the cabinet to support the door
• Helps maintain alignment for smooth opening/closing and proper gasket contact
• Common fix for a sagging, rubbing, or misaligned door
• Replaces a bent, cracked, or worn bracket

• Disconnect power and support the door before loosening center hinge fasteners
• Remove the old bracket and transfer the hinge and any spacers/washers to the new bracket if applicable
• Install the new bracket, align the door, then tighten screws securely
• Verify smooth swing and full gasket contact; readjust if needed

Color: White

This control box is the molded assembly in the refrigerator compartment that supports the temperature control and air duct components. Replacing a cracked or sagging box helps restore a secure mount and proper airflow routing. What it does

• Mounts the cold control/thermostat and the air diffuser/ducting in the fresh food section
• Helps channel cold air from the freezer into the refrigerator compartment
• Provides attachment points for control knobs and trim
• Typical failure signs: broken tabs, drooping housing, loose control dial, rattling, or obstructed airflow path

• 1 control box

• Disconnect power to the refrigerator before servicing
• Remove shelves/cover to access; take photos to note wiring and component locations
• Transfer existing controls and hardware as needed, then reinstall the housing with original fasteners
• Verify the damper moves freely and controls operate before restoring power

This compressor mounting clip secures the compressor to its chassis to reduce movement and noise for reliable operation. It replaces worn or broken clips that allow the compressor to shift during use. What it does:

• Holds the compressor in place on the mounting bracket to prevent shifting
• Reduces vibration and rattling noises caused by a loose mount
• Helps maintain proper compressor alignment for steady operation
• Useful when a cracked or bent clip no longer secures the compressor

• Disconnect power to the appliance before accessing compressor area
• Inspect surrounding mounts and rubber isolators; replace if damaged
• Secure clip fully so compressor is held without forcing or misaligning components

Color: White

This air diffuser kit replaces the vent/damper assembly that meters cold air from the freezer into the fresh-food section. It restores proper airflow and temperature balance when the original diffuser is stuck, broken, or leaking around the vent.

• Regulates and directs airflow from the freezer to the refrigerator compartment to maintain set temperatures
• Opens/closes the damper to reduce warm or cold spots in the fresh-food section
• Helps resolve symptoms such as a warm refrigerator with a normal freezer, weak airflow at the diffuser, temperature swings, or frost/condensation near the vent
• Replaces cracked housings, missing seals, or jammed/broken damper blades

• Disconnect power before servicing; wear cut-resistant gloves
• Remove shelves/covers to access the diffuser; note part orientation and screw locations
• Ensure all seals seat properly to prevent air leaks; do not overtighten plastic fasteners
• Restore power and allow up to 24 hours for temperatures to stabilize; adjust controls as needed