Fftr1835vw Parts

The Cold Control is an OEM part for Frigidaire refrigerators. It plays a key role in regulating the refrigeration cycle and maintaining optimal temperatures inside the refrigerator and freezer compartments. The cold control sensor monitors interior conditions and signals the compressor and condenser fan module to turn on or off accordingly.

Causes of bad cold control can include fatigue of internal components from repeated cycling over the refrigerator's lifespan, mineral or moisture buildup affecting sensors and circuitry, or failure due to sudden temperature fluctuations. 

Symptoms of a bad cold control include:

• Inconsistent or fluctuating temperatures within compartments
• The refrigerator or freezer running constantly 
• Food not staying freshest as long as expected
• Frost or ice buildup inside that is difficult to remove

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This bearing supports and allows smooth rotation of the dryer drum, helping reduce noise and wear. Replacing a worn bearing restores stable drum movement and helps prevent scraping, thumping, or drag during cycles.

• Supports the rear of the drum for proper alignment and smooth rotation
• Can help address squeaking, grinding, scraping, or thumping sounds
• Reduce drum wobble, drag, or intermittent stopping during operation
• Wear item that can degrade over time with heat and load stress

• Disconnect power before service and allow components to cool
• Access typically requires removing the top and front panels
• Inspect the drum shaft, support bracket, and glides for wear; replace if needed
• Apply manufacturer-approved high-temp lubricant where specified

The Hook is an OEM part for Frigidaire refrigerators. It helps to ensure a secure and proper closure of the refrigerator door.

A bad door closer hook can be caused by wear and tear, damage, or misalignment. Signs of a faulty door closer hook include the door not closing fully or not staying closed, difficulty in opening or closing the door smoothly, or a loose or wobbly door.

Symptoms of a bad door closer hook can include:

• The refrigerator door not sealing properly
• Excessive force required to open or close the door
• Visible damage or misalignment of the door closer hook

Replace your worn or damaged door closer hook with this genuine OEM part to restore your refrigerator door. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This refrigerator grommet is a small sealing/cushioning insert used where a tube, wire, or component passes through the cabinet or mounts to a panel. It helps keep the opening sealed and protected for reliable operation.

• Seals and cushions an opening or mounting point in the refrigerator cabinet
• Helps prevent water leaks and warm-air infiltration that can lead to frost or moisture
• Reduces chafing, vibration, and wear on tubing or wiring
• Replace if the grommet is cracked, hardened, misshapen, or missing

• Unplug the refrigerator and, if applicable, shut off the water supply
• Access the grommet location by removing any cover or panel as needed
• Remove the old grommet, clean the opening, and press the new grommet fully into place; route the line/wire without kinks
• Restore power (and water, if used) and check for proper sealing and operation

This replacement refrigerator bin restores safe, organized storage space inside your appliance. It securely holds bottles, jars, and small items so they don't tip, spill, or get lost—helping you maximize capacity and keep contents easy to reach. What it does:

• Provides contained storage for food and beverages in the designated compartment
• Attaches to molded supports/rails for stable, removable organization
• Replaces cracked or broken bins to restore usable space
• Common symptoms: stress cracks, broken tabs, bin won't stay seated, items falling or spilling

• 1 bin

• Remove contents, then lift the old bin up and out from its supports
• Align the new bin on the supports; slide or press down until fully seated
• Do not force or overload; verify placement and orientation per your model
• Minimize door-open time to maintain temperature; no electrical work required

Color: Black

The Condenser Fan Motor is an OEM part for Frigidaire refrigerators. Located behind the rear refrigerator wall and grille, the condenser fan motor works to dissipate heat from within the refrigerator system. 

Symptoms of a bad condenser fan motor include:

• Refrigerator failing to adequately cool or ice up  
• Increased humming and vibrations
• Elevated compressor run times 
• Warm air discharge from rear grill

Causes of a bad condenser fan motor can include winding failures, bearing seizing, or obstructed fan blades no longer spinning freely.

This genuine OEM Frigidaire motor is compatible with some Electrolux, KitchenAid and Danby French door refrigerator models as well.

The Screw is an OEM hardware component specifically designed for Frigidaire refrigerators. These fasteners secure interior shelves, bins, and exterior trim panels through precise threaded shafts. 

Symptoms of damaged or missing screws include:

• Shelving and bins becoming loose or detached within the fridge
• Door and side panel seals shifting out of position

Causes related to normal wear from repeated shelf adjustments over years of use. Potential impacts during moves can also strip or bend screws.

This OEM Frigidaire hardware is also compatible with Electrolux and Crosley refrigerators. Replacing loose or damaged screws preserves proper mounting of critical refrigerator accessories as intended by engineering specifications. Maintaining the integrity of small components avoids potential repairs.
 

This aluminum strap secures the defrost heater firmly against the evaporator coil to maintain proper contact during defrost. Correct contact improves heat transfer so frost melts evenly and helps prevent recurring ice buildup on the evaporator.

• Secures the defrost heater to the evaporator for proper contact and heat transfer
• Promotes complete, even defrosting across the evaporator coil
• Helps reduce repeat frost/ice accumulation caused by a shifted or loose heater
• Typical clues include a loose heater, uneven frost pattern, or rattling near the evaporator

• Disconnect power and allow ice to melt before accessing the evaporator
• Use care around sharp fins and fragile refrigerant tubing; do not puncture or deform the coil
• Position the heater per your model's parts diagram and tighten the strap for firm, even contact
• Verify wiring is routed clear of the fan and moving parts before reassembly

The Door Hinge is an OEM part for Frigidaire refrigerators. It is a component that allows the refrigerator door to swing open and closed easily while ensuring a proper seal is maintained each time. The hinge supports the weight of the door and controls its movement into both open and closed positions.

Causes of a bad hinge can include continued normal wear and tear over time, damage from excessive weight or impact, or corrosion that causes mechanisms to freeze up or fail.

Symptoms of a bad hinge include:

• The door not sealing properly when closed
• Difficulty in opening or closing the door
• The door swinging open or closed unintended
• Noise or squeaking coming from the hinge area

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Refrigerator Hook-Auto Closer is an OEM part for Frigidaire French door refrigerators. Located on the top inside edges of the refrigerator doors, the hook-auto closer attaches the closing mechanism arms to allow automatic opening and closing functions. 

Symptoms of a bad hook-auto closer include: 

• Doors detached from closing mechanism  
• Linkages slipping out of place 
• Loose or unstable door movement
• Grinding noises when doors open or close

Causes of a bad hook-auto closer can be damage or deformation from excessive impact, broken weld points, or normal wear over time.

This genuine Frigidaire part is compatible with some Electrolux and Kenmore French door refrigerator models as well.

This door shelf bin restores usable storage on the inner door. Replace a cracked, broken, or missing bin to keep items organized and help prevent spills when opening and closing the door.

• Attaches to the door liner to hold food items and containers
• Replace if the original is cracked, warped, or has broken mounting tabs
• Common symptoms: bin falls off or won't stay seated, reduced door storage, items tipping or sliding
• Restores proper fit and organization on the door

• Empty the bin and support the door while working
• Remove the old bin by lifting up and out; align the new bin with the door rails and press down until fully seated
• Do not force; ensure you're installing in the correct door position for this bin
• No electrical work required; handle plastic parts carefully to avoid cracking

This hinge assembly restores smooth, controlled door movement and proper alignment so the door closes flush and latches reliably. Replacing a worn hinge can help eliminate binding, sagging, or gaps that compromise performance.

• Provides the pivot and support point for the door
• Helps keep the door square to the cabinet for consistent latching and sealing
• Restores smooth opening/closing action
• Common failure symptoms include door sagging, rubbing/binding, squeaking, or not staying closed

• Disconnect power to the appliance before servicing
• Support the door to prevent strain on remaining hinges
• Mark orientation, transfer any original spacers/bushings, and reinstall hardware securely
• Verify door alignment and latch operation after installation

This auto-closer hook mounts at the door hinge and engages the closer/cam to help pull the door shut for a reliable seal. Replace a worn or broken hook to restore smooth, consistent self-closing action. What it does

• Couples the door to the hinge's auto-closer/cam mechanism
• Helps the door finish closing and stay closed
• Reduces bounce-back so the gasket can seal properly
• Common symptoms: door won't self-close, pops back open, feels loose at the lower hinge, or the original hook is cracked/worn

• 1 auto-closer hook

• Disconnect power before servicing; support the door and use a helper if removing it from the hinge
• Access the lower hinge/closer area; remove the damaged hook and transfer any spacers or screws
• Install the new hook in the same orientation; tighten hardware securely
• Recheck door alignment and inspect the mating cam/closer if issues persist

Replace a cracked or missing cover with this cover assembly. It safeguards internal components and restores a secure, finished fit so the area it protects functions and looks the way it should.

• Shields internal wiring and mechanisms from dust, spills, and accidental contact
• Helps maintain proper coverage and airflow around the protected area
• Secures panels to reduce vibration and rattling
• Replace if cracked, warped, missing, or if mounting tabs are broken and the cover won't stay in place

• Disconnect power to the appliance before servicing
• Retain and reuse original mounting screws/clips unless new hardware is supplied
• Transfer any attached seals, foam, or brackets from the old cover if present
• Align and tighten fasteners evenly; avoid overtightening and verify the cover clears any moving parts before restoring power

The Frigidaire refrigerator center door hinge pin is an OEM replacement part responsible for providing stability and allowing the smooth opening and closing of the refrigerator door. It secures the center hinge of the refrigerator door, ensuring proper alignment and movement of the door. The hinge pin is typically located in the center of the refrigerator door, connecting it to the refrigerator cabinet

Causes of a bad pin can include regular wear and tear, corrosion due to exposure to moisture, or physical damage from impact or mishandling.

Symptoms of a bad pin include:

• Loose or misaligned components
• Unusual noises during operation
• Difficulty in opening or closing doors or panels
• Parts not staying securely in place

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.