Fge3055mfe Parts

The Fresh Food Door Gasket is an OEM replacement part for Frigidaire refrigerators. It creates a seal around the refrigerator door to maintain a consistent temperature by keeping cold air in and warm air out. This helps ensure proper refrigerator conditions and prevents energy loss.

Over time, gaskets can degrade due to wear, exposure to extreme temperatures, or cleaning with harsh chemicals. A damaged or worn gasket may fail to seal properly, affecting the freezer's efficiency and potentially leading to increased energy consumption.

Symptoms of a bad gasket include:

• Frost or ice buildup inside the refrigerator
• Difficulty keeping the refrigerator door fully closed
• Warm air entering the refrigerator, causing temperature fluctuations
• Increased energy bills due to inefficient operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

NOTE: GASKET NOW GRAY, NOT WHITE

This water filter base secures the refrigerator's replaceable water filter cartridge and directs filtered water to the dispenser and icemaker. Replacing a damaged base restores a proper seal and helps prevent leaks and flow interruptions. What it does:

• Holds and seals the water filter cartridge so water passes through the filter media
• Directs filtered water to the dispenser and icemaker plumbing
• Prevents leaks caused by cracked or worn filter housing
• Can resolve low water flow, intermittent dispensing, or water taste issues when base is leaking or not sealing

• One water filter base assembly

• Turn off refrigerator and shut off the water supply before starting
• Relieve system pressure by dispensing water until flow stops, if applicable
• Remove the old housing carefully; inspect O-rings and replace if damaged
• Hand-tighten only; check connections and test for leaks after restoring water and power

The Lens is an OEM component for Frigidaire freezers. It acts as a transparent cover and protective barrier for the freezer compartment lights. Crafted for durability and clarity, the lens avoids frost and minimizes condensation while allowing visibility inside the freezer.

Causes of a bad lens can include deep scratches or cracks developing over time from repeated wiping or exposure to chemicals like frost removers.

Symptoms of a bad freezer lens include:

• Cloudiness, fogginess, or smears inhibiting internal visibility
• Cracks or breaks compromising the protective barrier
• Distorted views make it difficult to assess food levels
• Diffused lighting with shadows instead of a clear view

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Door Lock Motor and Switch Assembly is an OEM component specifically designed for Frigidaire ranges. This locking system safely secures oven doors during cleaning or self-clean cycles through the electromagnetic operation. 

Symptoms of a defective assembly include: 

• Failure to engage or release the door lock function
• Loud buzzing or grinding noises from internal mechanisms  
• Error codes related to door lock detection problems

Causes relate to wear from continual operation of locking solenoids over extended use. Exposure to cooking residues and cleaning chemicals can deteriorate switches. 

This OEM Frigidaire part is also compatible with some Kenmore and GE appliance brands. Replacing worn components restores reliable door locking to automatically secure during high-heat cycles. Timely maintenance preserves safety functionality.
 

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head

This refrigerator water filter mount secures the filter head/housing to the liner so the cartridge seats squarely and seals. Replace a cracked or loose mount to restore a snug fit and help prevent leaks or vibration.

• Holds the water filter housing firmly in place
• Aligns the cartridge for proper engagement with the filter head
• Helps maintain a watertight seal at the filter connection
• Common symptoms: filter won't lock in or sits crooked, drips around the filter area, difficulty installing/removing the filter, or rattling from a loose housing

• Disconnect power and shut off the water supply; dispense water to relieve line pressure
• Remove the filter and any cover/trim to access the mount; retain existing screws for reuse
• Install the new mount and tighten screws gently to avoid cracking plastic
• Reinstall the filter, restore water and power, flush the dispenser, and check for leaks

Restore smooth, level oven rack movement with this right-side rack support. It mounts to the oven wall to hold and align the racks at the correct heights so cookware stays stable while baking and roasting.

• Mounts on the right interior wall to support and guide oven racks
• Keeps racks level and properly spaced across multiple positions
• Replaces a bent, cracked, or missing side rail
• Typical symptoms: racks wobble, bind, tilt, or won't slide in/out smoothly

• Disconnect power and allow the oven to cool before servicing
• Remove oven racks to access the side support
• Retain and reuse existing mounting hardware unless directed otherwise by your model's service instructions
• The rail is seated and level before reinstalling the racks

This electrical switch restores reliable on/off control to the designated circuit in your appliance. Replacing a worn or stuck switch helps ensure lights, fans, or motors operate only when they should. What it does

• Opens and closes an electrical circuit when actuated
• Helps correct issues like a light that won't turn on/off or a component that won't run or won't stop running
• Resolves intermittent operation caused by worn contacts or a loose/broken actuator
• Addresses signs such as melted/discolored terminals or an unusually loose/tight switch feel

• 1 switch

• Disconnect power to the appliance before servicing (unplug or switch off the circuit breaker)
• Access the switch location per your model's service information
• Photograph wire positions and transfer connectors one at a time to the new switch; do not force terminals
• Secure the switch, reassemble, restore power, and test operation

This support beam is the structural rail that supports a refrigerator shelf and its pantry/drawer assembly. Replace a cracked or missing beam to restore level support, prevent sagging, and keep drawers operating smoothly.

• Spans the compartment to support the shelf/pantry frame and distribute weight
• Keeps the shelf level and stable under load
• Helps maintain proper alignment for attached drawers or bins
• Common symptoms: shelf tilts or sags; drawers bind, scrape, or drop
• Visible cracks, broken tabs, or a missing beam

• Disconnect power before servicing
• Remove food items, the shelf/frame, and any drawers or bins supported by the beam
• Release the beam from locking tabs or fasteners and remove the old part
• Seat the new beam fully in the mounting points, then reinstall the shelf and drawers and check for level

Restore reliable heat with this replacement heating element. A worn or damaged element can cause long heat-up times, uneven temperatures, or no heat at all. Swapping it out helps return consistent, dependable heating performance.

• Converts electrical energy to heat when energized
• Common symptoms: no heat, slow to heat, or uneven/inconsistent temperatures
• Visual clues: cracks, breaks, burn spots, or terminals damaged/corroded
• Helps resolve heat-related error codes after proper diagnosis

• Disconnect power at the breaker before servicing; verify no voltage present
• Note wire positions and terminal orientation before removal
• Handle carefully; avoid stressing terminals and element sheath
• Inspect wiring and connectors; replace any heat-damaged spade terminals before reassembly

This 100W radiant element replaces a failed warming element to restore gentle, even heat in the appliance's warmer/drawer. It delivers low-profile radiant heat for keeping food warm between cooking and serving. What it does:

• Radiates low-level heat to maintain food temperature in the warmer or drawer
• Replaces a broken or non-heating warmer element
• Common symptom: warmer drawer not holding temperature or not heating
• Works as the heating element that sits under the warming surface to provide consistent warmth

• Disconnect power to the appliance before attempting service
• Inspect mounting and wiring; replace any damaged connectors or mounting hardware as needed
• Handle the element carefully to avoid bending or damaging the heating surface

This is a smoothtop assembly intended for use with ranges by major manufacturers. This component is located on top of the stove and protects the wiring and heating elements on the interior. The smoothtop assembly is made of strong glass. This part can become damaged and may be unsafe for use. If this happens, the smoothtop assembly will need to be replaced.A set of basic tools will be needed to replace this part. Work gloves can also be useful for preventing injuries from broken glass. First, turn off the range. Unplug it from the wall and make sure it is cool to the touch. Open the oven to remove the screws that hold the smoothtop assembly in place. Pick it up and disconnect the heating elements and wires. Next, install the new smoothtop assembly and hook back up the internal components. Plug in the appliance before use.This is an authentic OEM replacement component that is sourced directly from the manufacturer. It is sold on an individual basis. The smoothtop assembly is made to be used with ranges, ovens, and stoves created by Ikea, Frigidaire, and Crosley.

This hex head screw secures panels, brackets, and small components on appliances, restoring proper fit and stability. It's a direct replacement fastener when an original mounting screw is missing, loose, or damaged. What it does:

• Secures panels, brackets, trim, and internal components to prevent rattling or movement
• Replaces stripped, missing, or damaged mounting screws that cause loose parts or misalignment
• Restores reliable mechanical fastening so doors and panels sit flush and operate correctly
• Works as a general-purpose appliance mounting screw when original fasteners are worn

• Always disconnect power to the appliance before starting any repair
• Match the screw to the original location and thread engagement; start by hand to avoid cross-threading
• Use the correct driver or socket for the hex head and tighten until snug—do not overtighten
• If the original hole or threads are damaged, repair or replace the mating hardware before installing the screw

This cover shields the control knob housing, protecting internal switch components and giving the control panel a finished look. Replacing a damaged cover helps keep debris out and maintains proper knob alignment and appearance.

• Protects the control area from dust, moisture, and accidental contact
• Helps maintain smooth knob operation and alignment
• Common failure signs: cracked or missing cover, loose knob feel, exposed control components
• Restores a clean, finished look to the control panel

• Disconnect power before servicing
• Pull off the knob, then release any tabs or screws retaining the cover
• Note orientation before removal; seat the new cover fully
• Reinstall knob and test for proper fit and operation