Fghd4261kw1 Parts

This replacement gasket creates a tight seal between mating components to prevent air and moisture leaks. It helps restore proper airflow and efficiency and can reduce vibration and noise when the original gasket is worn or damaged.

• Forms a seal between parts to prevent air bypass and moisture intrusion
• Helps maintain proper airflow and overall performance
• Cushions components to reduce vibration and rattling
• Replace if the gasket is torn, brittle, compressed, or missing
• Common symptoms include drafts/air leaks, condensation at the seam, unusual noise, or reduced cooling/dehumidifying performance

• Disconnect power to the appliance before servicing
• Remove covers or panels to access the sealed joint; note the gasket's routing/orientation
• Clean and dry mating surfaces; remove old adhesive/foam debris
• Install the new gasket without stretching; press evenly, reassemble, and check for a uniform seal

Replacement door bin for the refrigerator door. This snap-in shelf restores secure, organized storage on the door so bottles, condiments, and small items stay in place and easy to access.

• Holds items on the refrigerator door; also called a door shelf or rack
• Replaces cracked, broken, or missing bins
• Helps prevent items from tipping or falling when the door opens
• Common symptoms: bin won't stay seated, broken tabs, sagging, or lost door storage

• Remove contents from the old bin; lift it up and off the door mounting tabs
• Align the new bin with the same slots and press down until it clicks firmly into place
• Match the bin to the correct door position—some models use different-width bins by location
• Handle cold plastic gently; let it warm to room temperature to reduce the chance of cracking

This float detects and monitors water levels in the appliance's sump/drain area to help prevent overfilling and water pooling. Replacing a damaged or stuck float restores proper water sensing and reduces leak risk. What it does:

• Senses water level in the drain pan or sump so the appliance can stop or redirect water flow
• Helps prevent water from overflowing or pooling under the appliance
• Can stop false fill/overfill conditions caused by a stuck or broken float
• Fault symptoms include water pooling, continuous or unexplained filling, or failure to drain properly

• Always unplug the appliance before accessing internal panels or service areas
• Remove the required access panels or trim to reach the sump/drain area; follow the model's service manual
• Handle the float and any clips or wiring carefully to avoid damage; reconnect any electrical connectors securely
• After installation, restore power and run a manual fill/drain test to verify proper operation

Color: Grey

Nylon

The Pump Cover is an OEM part for Frigidaire dishwashers. It is designed to cover and protect the dishwasher's pump, which is essential for the proper circulation of water during the wash cycle. This cover helps ensure that the pump operates efficiently and prevents debris from entering and damaging the pump.

Causes of a bad pump cover can include repeated exposure to high water pressure, accidental impact during loading or unloading of dishes, or buildup of debris and hard water deposits.

Symptoms of a bad Pump Cover include:

• Leaks coming from the pump area
• Unusual noises during the wash cycle
• Decreased washing performance
• Visible cracks or wear on the cover

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This cover assembly replaces a damaged or missing cover on your appliance, protecting internal components and restoring a clean, finished appearance. Use it when the original is cracked, loose, or no longer secures properly.

• Shields internal parts from debris, spills, and accidental contact
• Helps keep components enclosed and aligned for reliable operation
• Restores the appliance's finished look after damage or wear
• Common signs of failure: cracks, broken or missing tabs, discoloration, rattling, or a cover that won't stay in place

• Disconnect power before servicing; shut off water supply if working near water connections
• Remove retaining screws or release tabs; note the orientation of the original cover
• Transfer and reuse original screws, clips, or seals if required
• Do not overtighten fasteners into plastic; ensure all tabs fully engage before testing

This replacement guide aligns and supports a moving component so it travels on its intended path without binding. Replacing a worn or broken guide restores smooth operation and helps prevent scraping, jamming, or premature wear of connected parts.

• Keeps the associated rack, drawer, or panel centered and properly aligned during movement
• Provides a track/stop for the mating part to follow
• Reduces friction and noise for smoother sliding
• Typical failure signs: sticking, uneven travel, scraping noises, or visible cracks/broken tabs

• Disconnect power; also shut off water or gas
• Remove the associated assembly to access the guide and note its orientation
• Reuse original screws/clips and tighten securely without overtightening
• Test movement after installation; replace worn mating rails or rollers if needed

This replacement bracket secures a component to the appliance frame, keeping it aligned and stable during operation. Install it to replace a bent, cracked, or missing bracket and restore a solid, rattle-free mount.

• Provides a rigid mounting point to hold the specified part in place
• Helps maintain alignment to reduce vibration, rubbing, or noise
• Replaces damaged or corroded hardware to restore a secure fit
• Common symptoms: loose or sagging component, unusual vibration/noise, or part shifting out of position

• Disconnect power before servicing; shut off water supply if working near water lines
• Note original orientation and fastener locations; take a reference photo
• Transfer and reuse existing screws/clips as needed; tighten fasteners evenly without over-torquing
• Verify alignment and test operation before final reassembly

This freezer air duct directs cold air from the evaporator fan through the freezer compartment, helping maintain steady temperatures and airflow. Replace a cracked, warped, or missing duct to restore consistent cooling and reduce frost or noise. What it does:

• Channels air from the evaporator fan outlet to the freezer vents for even cooling
• Helps maintain targeted freezer temperature and proper circulation
• A damaged or loose duct may contribute to weak airflow, frost buildup near vents, temperature swings, or rattling noises
• Seals the airflow path when properly seated to minimize leaks and hotspots

• 1 freezer air duct

• Disconnect power to the refrigerator before servicing
• Clear the freezer and remove any panels, shelves, or the ice bin as needed for access
• Remove mounting screws or clips, note seal orientation, and seat the new duct fully
• Reuse original hardware, restore power, and verify airflow from the vents

Color: light gray. Each prong goes out about 10 inches from the center.

This replacement screw secures refrigerator components such as brackets, trims, and covers. Replace missing or stripped hardware to keep parts tight and aligned, helping eliminate rattles and restoring a solid, reliable fit.

• Fastens interior or exterior components to the cabinet or doors
• Replaces missing, rusty, or stripped hardware
• Helps reduce vibration noises from loose parts
• Restores proper fit and alignment of panels, trims, or covers

• Disconnect power; turn off water supply if working near the dispenser or ice system
• Retain and reuse any original spacers or washers
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace one fastener at a time to maintain alignment

This refrigerator water tube carries fresh water between the valve, reservoir, dispenser, and/or ice maker. Replacing a cracked or kinked tube restores proper water flow and helps stop leaks inside or behind the refrigerator.

• Directs pressurized water between components in the refrigerator's water system
• Common failure signs: leaks, visible cracking, kinks, or pinhole sprays
• May cause no or slow dispenser flow, or an ice maker that doesn't fill
• Restores correct routing after tubing becomes brittle or damaged with age

• Unplug the refrigerator and shut off the household water supply before servicing
• Place a towel under connections and dispense water to relieve line pressure
• Depress quick-connect collars or loosen clamps to remove the old tube; route the new tube exactly like the original
• Fully seat tubing in fittings, perform a gentle tug test, restore water, check for leaks, and flush several cups to clear air

The Dispenser Control Board is an OEM part for Frigidaire refrigerators featuring interior dispensers. It oversees dispensing of ice and water according to user selection. Located within the refrigerator door panel, it activates motors and solenoids.

Symptoms of a bad dispenser control board include:  

• Inability to dispense ice or water from lever/button
• Dispenser motors or solenoids not activating properly   
• Unresponsive or stuck dispenser lights and selection buttons
• Water or ice volumes not measured accurately

Causes can be long-term moisture exposure degrading circuitry or power surges overloading sensitive components. Proper drying and periodic cleaning help prevent issues.

This genuine OEM control board is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore refrigerator models.

This strike is the receiver the door latch engages with to keep the door securely closed. A properly aligned strike helps the appliance recognize a closed door so cycles can start and run without interruption. What it does

• Provides the catch point for the door latch to secure the door during operation
• Helps align the latch for smooth, consistent engagement
• Ensures the door-closed switch can be activated so the unit can start
• Worn, bent, or broken strikes can cause the door not to latch, pop open, or trigger door-open errors

• 1 strike

• Disconnect power before servicing; follow manufacturer safety procedures
• Note the strike's orientation and any shims/spacers before removal
• Reuse existing mounting hardware unless your model specifies otherwise
• After installation, check alignment and the latch engages smoothly without force

This dispenser drip tray sits at the base of the refrigerator's ice/water dispenser. It catches small drips and splashes to help keep the dispenser recess and door front cleaner and drier. What it does:

• Collects minor drips and splashes from the ice and water dispenser
• Helps protect the door finish and surrounding area from moisture
• Replace if the tray is cracked, warped, stained, or missing
• Common signs include water pooling in the dispenser recess or a loose, ill-fitting tray

• 1 dispenser drip tray

• Pull the old tray straight out of the dispenser recess; no tools are typically required
• Clean any mineral deposits or debris in the recess before installing the new tray
• Align and seat the new tray flat and flush in the opening
• Disconnect power and shut off water