Fphb2866lf8 Parts

This replacement guide aligns and supports a moving component so it travels on its intended path without binding. Replacing a worn or broken guide restores smooth operation and helps prevent scraping, jamming, or premature wear of connected parts.

• Keeps the associated rack, drawer, or panel centered and properly aligned during movement
• Provides a track/stop for the mating part to follow
• Reduces friction and noise for smoother sliding
• Typical failure signs: sticking, uneven travel, scraping noises, or visible cracks/broken tabs

• Disconnect power; also shut off water or gas
• Remove the associated assembly to access the guide and note its orientation
• Reuse original screws/clips and tighten securely without overtightening
• Test movement after installation; replace worn mating rails or rollers if needed

This is the vertical flipper mullion assembly that mounts to one fresh-food door and pivots closed to seal the center gap when both refrigerator doors are shut, helping maintain proper temperature and energy efficiency.

• Creates the center seal between French-door refrigerator doors
• Helps prevent warm air infiltration and moisture/condensation in the fresh-food section
• Common failure signs include a loose or broken hinge, mullion not staying aligned, condensation at the door center, or doors not sealing properly
• May also be noted if doors pop open or temperature fluctuates in the refrigerator compartment

• Unplug the refrigerator before servicing
• Remove door bins to access mounting screws/clips
• Transfer any original covers or hardware if not part of the new assembly
• Verify proper hinge engagement so the mullion flips and seals smoothly before restoring power

This freezer air duct directs cold air from the evaporator fan through the freezer compartment, helping maintain steady temperatures and airflow. Replace a cracked, warped, or missing duct to restore consistent cooling and reduce frost or noise. What it does:

• Channels air from the evaporator fan outlet to the freezer vents for even cooling
• Helps maintain targeted freezer temperature and proper circulation
• A damaged or loose duct may contribute to weak airflow, frost buildup near vents, temperature swings, or rattling noises
• Seals the airflow path when properly seated to minimize leaks and hotspots

• 1 freezer air duct

• Disconnect power to the refrigerator before servicing
• Clear the freezer and remove any panels, shelves, or the ice bin as needed for access
• Remove mounting screws or clips, note seal orientation, and seat the new duct fully
• Reuse original hardware, restore power, and verify airflow from the vents

This slide set replaces the side guides that support a sliding rack or drawer inside your appliance. Fresh slides restore smooth in-out movement, keep alignment true, and help prevent binding or derailment.

• Supports and guides a rack or drawer for smooth travel
• Helps maintain alignment and reduces friction during use
• Replaces cracked, warped, or worn slides that cause sticking or grinding
• Can help resolve binding, uneven movement, or a rack/drawer that pops off the track

• Disconnect power; shut off water or gas if applicable
• Remove the rack/drawer and retain any end stops, clips, or screws
• Note right/left orientation; transfer reusable hardware to the new slides
• Test full travel and smooth operation before returning to service

This replacement screw secures refrigerator components such as brackets, trims, and covers. Replace missing or stripped hardware to keep parts tight and aligned, helping eliminate rattles and restoring a solid, reliable fit.

• Fastens interior or exterior components to the cabinet or doors
• Replaces missing, rusty, or stripped hardware
• Helps reduce vibration noises from loose parts
• Restores proper fit and alignment of panels, trims, or covers

• Disconnect power; turn off water supply if working near the dispenser or ice system
• Retain and reuse any original spacers or washers
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace one fastener at a time to maintain alignment

This is the complete ice container assembly for the dispenser. It stores ice and drives cubes to the chute so your dispenser can deliver ice reliably and without jams.

• Holds finished ice in the freezer and feeds it to the dispenser
• Integrated auger moves and helps break up ice for consistent dispensing
• Common failure signs: ice not dispensing, auger not turning, loud grinding, or cracked/leaking bucket
• Restores proper in-door ice dispensing performance

• Unplug the refrigerator and remove the ice bin from the freezer door or shelf
• Transfer any remaining ice to a cooler; let any frost melt to avoid damage
• Align the drive coupling and slide the new bin fully into place
• Restore power and test ice dispense for cube and crush functions

This main power control board assembly is the refrigerator's central controller. It manages power to the compressor, fans, and defrost system so the unit cools consistently and responds correctly to temperature settings.

• Distributes and regulates power to the compressor, condenser/evaporator fans, and defrost components
• Processes inputs from temperature sensors and the user interface to coordinate cooling cycles
• Common symptoms it may address: not cooling or intermittent cooling, fans/compressor not running, unit won't defrost/ice buildup
• May also help with unresponsive controls or repeated clicking/buzzing from the control area

• Disconnect power before servicing; handle the board by the edges and use ESD protection
• Access location varies by model; typically mounted in a rear control compartment behind an access cover
• Photograph wiring and move connectors one at a time to the new board; ensure all locking tabs are fully seated
• Reinstall covers, restore power, and verify compressor/fans operate and cooling resumes

This is the drive gear for the ice maker module. It transfers motor power to the ejector/harvest mechanism so cubes release consistently; worn or stripped teeth can cause clicking, stalls, or little to no ice production.

• Transfers motor torque to rotate the ejector and complete the harvest cycle
• Replaces a cracked, stripped, or worn gear that prevents proper ice ejection
• Typical symptoms: no ice production, icemaker stuck mid-cycle, clicking or grinding from the module
• Helps restore reliable ice maker cycling

• Unplug the refrigerator before service; turn off the water supply if moving the icemaker
• Remove the icemaker assembly for access; note the original gear's orientation before removal
• Align the new gear with the shaft; do not force it—inspect mating parts for wear
• After reassembly, verify the ejector turns freely; restore power and run a test cycle

This dispenser drip tray sits at the base of the refrigerator's ice/water dispenser. It catches small drips and splashes to help keep the dispenser recess and door front cleaner and drier. What it does:

• Collects minor drips and splashes from the ice and water dispenser
• Helps protect the door finish and surrounding area from moisture
• Replace if the tray is cracked, warped, stained, or missing
• Common signs include water pooling in the dispenser recess or a loose, ill-fitting tray

• 1 dispenser drip tray

• Pull the old tray straight out of the dispenser recess; no tools are typically required
• Clean any mineral deposits or debris in the recess before installing the new tray
• Align and seat the new tray flat and flush in the opening
• Disconnect power and shut off water

This replacement part is a set screw, and it is intended for use in different types of appliances. This is a genuine replacement part made by Frigidaire. This screw set is compatible in many different areas of the appliance. Screws are typically used for keeping parts of the machinery secure and in place. It is possible that screws can become loose over time and need to be replaced. A new screw set might be needed if the user notices parts of the appliances are becoming loose or are falling off. This can be due to screws becoming stripped over time or if the appliance is bumped during transport. It is typically easy to replace screws. Simply remove the old screw and replace it with a new part. The only tools needed for this repair are a screwdriver and possibly pliers if the damaged screw is stuck in place.Note that this is a genuine OEM replacement part and is sourced from the manufacturer. This set screw is sold individually.

This thermistor is a temperature-sensing resistor that monitors internal temperature and reports it to the control. Replacing a faulty sensor restores accurate temperature feedback for proper operation and consistent, reliable cycle performance. What it does:

• Continuously measures temperature and changes resistance for the control to read
• Helps regulate heating/cooling and overall cycle timing
• Supports safety logic that prevents improper temperatures
• Failure may cause inaccurate temperatures, long/short cycles, or temperature-related error codes

• 1 thermistor

• Disconnect power before servicing; shut off water or gas if applicable
• Access the sensor, note wire routing/orientation, and transfer any existing clip or seal as needed
• Make secure electrical connections and route wires away from hot or moving parts
• Many appliances use multiple sensors—diagnose with an ohm/diagnostic test before replacement, then run a test cycle after install

This dispenser control board is the electronic module behind the refrigerator's ice/water dispenser panel. It reads button inputs and powers dispenser functions to help restore reliable dispensing and front-panel control when the original board fails. What it does

• Processes user selections for water, cubed/crushed ice, and dispenser light (model-dependent)
• Sends power to the water inlet valve and auger/dispenser motor as commanded
• Manages dispenser lock and status/display indicators (if equipped)
• Failure symptoms include unresponsive or intermittent controls, no water or ice dispensing, or an inoperative dispenser light

• Includes 1 dispenser control module (electronic board)

• Disconnect power before servicing; use ESD protection and handle the board by its edges
• Remove the dispenser escutcheon/cover to access the module; release locking tabs or screws as needed
• Transfer wire connectors one at a time to the new board, confirming orientation and full seating
• Reassemble, restore power, and test all dispenser functions

This door bin guard secures items on a refrigerator door shelf, preventing bottles and containers from sliding out. Replace it when cracked or missing to restore safe, usable door storage. What it does:

• Mounts to the front of a door bin to hold contents in place
• Replaces a broken, warped, or missing guard
• Helps resolve issues like items falling from the door shelf or a loose/broken bar
• Restores usable door storage space

• 1 door bin guard

• Unplug the appliance or disconnect power before servicing
• Empty the affected bin; release the old guard and align/snap the new guard into the slots
• Let cold plastic warm to room temperature before installation to reduce the risk of cracking
• The guard is fully seated before reloading items

This refrigerator water inlet tube routes water from the supply/valve into the appliance's water system. Replacing a cracked or kinked tube restores proper flow to the dispenser and ice maker while helping prevent leaks.

• Directs water from the inlet valve to internal components for dispensing and ice production
• Maintains a sealed, food-grade water path
• Replace if you notice leaks under/behind the unit, visible cracks/kinks, reduced or intermittent dispenser flow, or ice maker not filling
• Normal wear, brittleness, or damage during moves can lead to failures

• Disconnect power and shut off the water supply before servicing
• Place a towel or tray to catch residual water when disconnecting lines
• Note the original routing; release any retaining clips and disconnect the tube from fittings
• Route the new tube exactly like the original and fully seat tube ends in connectors; restore water and check for leaks

This #10-32 x 3/4-inch machine screw secures appliance components such as panels, brackets, and handles. Using the correct length and thread helps restore a snug, rattle-free hold wherever this screw is specified by the manufacturer.

• Fastens components with a #10-32 machine thread and 3/4-inch length
• Helps keep panels, trim, brackets, or handles secured and aligned
• Replaces missing, stripped, or corroded hardware
• Common signs include loose or wobbly parts, rattling, missing screws, or damaged screw heads/threads

• Disconnect power before servicing; if working near a water connection, shut off the water supply
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten to prevent stripping plastic or threads
• Reuse any model-specific washers or spacers if present

This turntable roller assembly sits under the glass tray to support and guide it as it rotates. Replacing a worn or damaged ring helps restore smooth tray movement for more even heating and dependable microwave performance.

• Supports the glass tray and allows smooth, consistent rotation
• Helps prevent tray wobble, binding, or scraping noises
• Can address issues like the tray not turning or uneven cooking
• Replaces cracked, warped, or missing roller rings

• Disconnect power before servicing
• Remove the glass tray, lift out the old ring, and clean the cavity floor
• Place the new ring wheels-down, seat the tray on the coupler, and test rotation
• Do not operate the microwave without the roller ring and tray properly installed