Fpru19f8rf Parts

This sleeve is a small spacer/bushing used in select Frigidaire-built appliances to keep mating parts aligned and moving smoothly. Replacing a worn sleeve helps eliminate play, reduce friction, and restore proper operation.

• Provides a guided, low-friction surface between parts that slide or rotate
• Maintains correct spacing/alignment to prevent wobble and rubbing
• Helps reduce wear on shafts, pins, or fasteners it interfaces with
• Typical symptoms: looseness or wobble, squeaking/scraping noises, uneven movement, or visible cracking/missing sleeve

• Disconnect power before servicing; shut off gas/water if applicable to your model
• Use your model's diagram to locate the sleeve and note orientation before removal
• Clean and inspect the mating shaft/pin or fastener; replace any severely worn components
• Seat the sleeve fully; avoid over-tightening hardware that passes through the sleeve

Replacement slide restores smooth, reliable movement for a single appliance drawer or shelf. Replacing a worn or damaged slide can stop sticking, sagging, or misaligned travel and restore proper alignment. What it does:

• Guides and supports the drawer or shelf along its track for smooth opening and closing; symptoms: sticking, binding, or incomplete travel.
• Keeps the drawer aligned and prevents sagging or tilting; symptoms: drawer sits uneven or rubs against the cabinet.
• Replaces worn, cracked or broken slide hardware to reduce noise and catch/drag during use; symptoms: grinding, rattling, or sudden drops.
• Enables consistent load support and smoother operation after wear or accidental damage.

• Disconnect power or unplug the appliance if work requires removing panels near electrical components; follow appliance safety guidance.
• Remove drawer or shelf and inspect mating rails and fasteners; replace damaged screws or clips before installing the slide.
• Use appropriate hand tools and avoid forcing parts; align slide evenly and test full travel before returning the drawer to service.

This replacement screw secures appliance components so brackets, shelves, trim, or panels stay firmly in place. Install a new screw when the original is missing, stripped, or corroded to restore a tight, rattle-free fit.

• Fastens brackets, panels, trim, or covers to the cabinet or liner
• Helps maintain alignment and reduce vibration and noise
• Direct replacement for a missing, rusted, or stripped fastener
• Use wherever your model's parts diagram specifies this screw

• Disconnect power before servicing; shut off water if working near water lines
• Match thread and length to the original location as shown in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening (especially into plastic)
• Retain and transfer any original spacers or clips used with this fastener

This aluminum strap secures the defrost heater firmly against the evaporator coil to maintain proper contact during defrost. Correct contact improves heat transfer so frost melts evenly and helps prevent recurring ice buildup on the evaporator.

• Secures the defrost heater to the evaporator for proper contact and heat transfer
• Promotes complete, even defrosting across the evaporator coil
• Helps reduce repeat frost/ice accumulation caused by a shifted or loose heater
• Typical clues include a loose heater, uneven frost pattern, or rattling near the evaporator

• Disconnect power and allow ice to melt before accessing the evaporator
• Use care around sharp fins and fragile refrigerant tubing; do not puncture or deform the coil
• Position the heater per your model's parts diagram and tighten the strap for firm, even contact
• Verify wiring is routed clear of the fan and moving parts before reassembly

Quantity of 1 clip.

Note: See kit# 5303922007 and 5304406520.

This freezer hinge kit restores proper pivot and alignment to a freezer door, helping stop sagging, binding, and air leaks. Use it to replace worn or damaged hinge components for smoother, more reliable door operation. What it does:

• Supports the freezer door pivot points and maintains correct alignment to help the door seal evenly.
• Helps resolve symptoms such as door sag, binding when opening/closing, squeaks, or visible gaps at the door edge.
• Replaces worn or damaged hinge components that can cause poor sealing and reduced cooling efficiency.
• Fits into the existing hinge mounting locations to secure the door and restore proper movement.

• Always unplug the appliance or disconnect power before starting any repairs.
• Support and brace the door before removing the old hinge—use a second person if needed to prevent injury or damage.
• Use the correct tools and follow factory torque/fastening practices; avoid overtightening to prevent misalignment.
• After installation, check door alignment and sealing; make any minor adjustments so the door closes evenly.

This bracket is the factory support used to mount a component securely inside your appliance. Replacing a damaged bracket restores proper alignment and reduces vibration, keeping the part stable so it operates as designed. What it does:

• Provides a rigid mounting point for the designated component
• Maintains correct alignment to help prevent rubbing, rattling, or noise
• Replaces a cracked, bent, or missing bracket to restore secure fit
• Typical signs include vibration, a loose or misaligned part, or visible damage

• 1 bracket

• Disconnect power before servicing
• Wear cut-resistant gloves; cabinet edges can be sharp
• Reuse original screws/fasteners and any spacers or grommets from the old bracket
• Mount in the original position and tighten fasteners evenly without overtightening

This replacement screw secures panels, brackets, or internal components in select Frigidaire-made refrigerators and freezers. Use it to replace missing or stripped hardware and restore a secure fit to help reduce vibration and noise.

• Fastens appliance panels, brackets, and internal components
• Helps prevent vibration, rattling, or looseness from missing hardware
• Reliable fix when the original screw is missing, damaged, or stripped
• Designed for proper fit in the original threaded location(s) specified for this part number

• Disconnect power to the appliance before servicing
• Align parts and start the screw by hand to avoid cross-threading
• Tighten snugly; do not overtighten, especially into plastic components
• Reuse any original washers or clips if present and in good condition

This support is a small mounting bracket used inside the appliance to hold an interior component, such as a shelf or basket. Replacing a cracked or missing support restores a secure, level fit and helps prevent wobbling or dropping.

• Provides a stable mounting point for a shelf, basket, rail, or panel
• Keeps interior components aligned and level
• Common symptoms: shelf/basket tilts, won't seat, or falls; visible cracks or missing support
• Replace if broken, deformed, or worn to restore proper fit

• Disconnect power and clear the work area before starting
• Remove the affected shelf/basket/panel to access the mounting point
• Release the damaged support (snap tabs or remove screw), align, and install the new support
• Reinstall the component and verify it sits level and secure

This mounting bracket secures internal components or panels to restore proper alignment and reduce vibration. A simple, direct replacement that helps stop rattling, sagging or loose panels caused by a cracked or bent bracket. What it does:

• Holds and supports a component or panel to the appliance cabinet, maintaining proper fit and alignment.
• Prevents movement and vibration that can cause noise or wear.
• Replaces cracked, bent or broken brackets that cause loose panels, misalignment or rattling.
• Restores secure attachment points so doors, drawers or control housings sit correctly.

• One mounting bracket

• Disconnect power before starting any repair to avoid shock or injury.
• Basic hand tools (screwdriver, nut driver) are typically required; retain original fasteners unless replacements are provided.
• Inspect surrounding parts and mounting holes for damage; replace any worn screws or clips.

The EVAPORATOR INSULATOR is an OEM part for Frigidaire refrigerators. It is a heat-resistant insulating pad or wrap that surrounds the evaporator coils. The insulator works to retain cool air and prevent warmer air from entering the refrigerated compartment.  

Causes of a bad insulator can include deterioration or breakdown of insulating properties over time due to aging materials. Cracks, holes, or compressed sections of the insulator result in reduced insulation performance.

Symptoms of a bad evaporator insulator include:

• Inconsistently cool or warmer fridge temperatures 
• Frost or ice buildup on evaporator coils or surrounding areas
• Higher than normal electric bills from inefficient cooling
• Warm or cold spots inside refrigerator shelves and compartments

This OEM Frigidaire replacement insulator is compatible with some Kitchenaid, Electrolux, Gibson, Kelvinator, and Kenmore side-by-side refrigerator models. 

The Hinge-Lower is an OEM replacement part for Frigidaire refrigerators. It is the bottom hinge that attaches the freezer door to the refrigerator body, allowing smooth opening and closing of the door. As a moving part, these hinges endure stress and wear from frequent use over the lifespan of the appliance.

Causes of a bad lower hinge can include repetitive opening and closing cycles that degrade lubrication over time. General wear and tear or physical impacts that bend or warp the hinge assembly will reduce function.  

Symptoms of a bad lower hinge include: 

• Door not sitting flush or securely closing  
• Loose or sagging door that does not stay in position  
• Noisy “creaking” sounds when opening or closing
• Visible damage or separation of hinge components

This OEM Frigidaire replacement hinge is compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Screen - drain keeps the drain path clear by trapping lint and small debris before it reaches the pump or drain hose, helping reduce clogs and improve drainage. Simple replacement restores proper water flow and drain performance. What it does:

• Traps lint, hair and small debris to help prevent clogs in the drain path
• Helps maintain consistent water drainage and pump operation
• Replace if you notice slow draining, standing water, or visible debris at the drain opening
• Sits in the appliance's drain assembly to protect downstream components

• Disconnect power to the appliance before servicing; turn off the water supply if the model requires it
• Access the drain area per your model's service instructions (remove access panel or wash tub components as needed)
• Inspect surrounding seals and hoses for damage and clean mating surfaces before installing the new screen

This #8-32 x 3/8 screw secures appliance panels, brackets, and assemblies. Replace a missing or stripped fastener to keep parts tight and aligned, reduce vibration, and restore proper fit in compatible refrigerators and freezers.

• Machine-thread fastener sized #8-32, 3/8-inch length
• Secures control housings, trims, covers, and support brackets per model design
• Replaces missing, worn, or corroded screws that cause loose or rattling parts
• Helps maintain alignment and stability after service

• Unplug the appliance; shut off water if applicable
• Match thread size to the original and start by hand to avoid cross-threading
• Use the correct driver; do not overtighten, especially into plastic
• Verify component alignment and operation after fastening

• Thread size: #8-32
• Length: 3/8 inch

This condenser coil assembly removes heat from the refrigerant so the refrigerator can cool efficiently. Replacing a damaged or clogged condenser restores proper heat transfer and helps the unit run more reliably. What it does:

• Condenses refrigerant from a gas to a liquid by releasing heat to the surrounding air
• Helps maintain correct system pressures so the compressor cycles normally
• Commonly fixes symptoms like the fridge running constantly, higher-than-normal interior temperatures, or overheating at the rear/bottom of the cabinet
• Improves cooling efficiency when the original condenser is bent, crushed, or clogged with debris

• Disconnect power to the appliance before servicing.
• Inspect mounting brackets, lines, and electrical connections during replacement; replace any damaged fasteners or clips.
• Avoid bending fins; straighten with a fin comb if minor damage is present, and ensure adequate ventilation around the condenser after reinstalling.