Frigidaire Gas Range M Parts

This factory screw secures brackets, panels, and internal components so assemblies stay tight and aligned. Replace a missing or damaged fastener to eliminate rattles, looseness, and misaligned parts. What it does:

• Fastens components, panels, hinges, or brackets to the appliance frame
• Helps maintain proper alignment and a solid, rattle-free fit
• Replaces stripped, rusted, or missing hardware
• Can address vibration noises and loose assemblies

• Includes 1 screw

• Unplug the appliance and shut off water before servicing
• Wear gloves; sheet-metal edges can be sharp
• Start threads by hand to avoid cross-threading; use the appropriate driver
• Tighten snugly—do not overtighten to prevent stripping

This ice maker stripper is the front comb that helps release cubes from the ejector during harvest. It guides ice cleanly into the bin to reduce jams and keep ice production running smoothly. What it does

• Strips ice cubes off the ejector fingers as the ice maker cycles
• Directs cubes into the bucket, helping prevent jams and cube bridging
• Wear, cracks, or warping can cause cubes to stick, spill, or clump
• Symptoms include cubes piling at the front, clicking during harvest, or reduced/no ice

• 1 ice maker stripper

• Disconnect power and shut off water before servicing
• Remove the ice bin and access the ice maker front (remove cover if present)
• Release the old stripper (tabs/screws), align the new stripper with the ejector fingers, and seat it fully
• Reinstall cover and bin; restore power and allow a full cycle to verify operation

This center hinge pin is the pivot shaft for the door at the middle hinge on select refrigerators. Replacing a worn or bent pin restores proper door alignment and smooth movement to help the door close and seal correctly.

• Serves as the door's pivot on the center hinge
• Maintains correct door height and alignment
• Helps the door open and close smoothly without binding
• Common symptoms: door sagging or rubbing, squeaking, wobbling, or not closing fully/popping open

• Unplug the refrigerator and remove items from the door to reduce weight
• Support the door before removing the center hinge bracket fasteners
• Install the new pin on the center hinge; reuse original spacers/bushings in their original order
• Reassemble, then check door alignment and gasket contact; adjust the hinge as needed per your model

This center hinge supports and pivots the refrigerator door at the middle of the cabinet. Replacing a bent or worn hinge restores smooth door movement and a reliable seal to help maintain proper temperatures.

• Supports door weight and provides the center pivot for opening and closing
• Helps maintain door alignment for even gasket contact
• Wear or damage can cause sagging, rubbing, squeaks, or doors that won't close/seal
• Visible bending, looseness, or a damaged hinge bracket/pin indicates replacement is needed

• Disconnect power and remove items from the door to reduce weight
• Support the door and have a second person assist; note the order of any spacers/washers
• Remove mounting screws, replace the hinge, and reinstall while keeping the door square
• Verify the door swings freely and the gasket seals evenly; adjust alignment as needed

This ice maker fill cup directs water from the refrigerator fill tube into the ice maker mold so each cycle fills correctly. Replacing a damaged cup restores consistent ice production and helps prevent water spills. What it does:

• Channels water from the fill tube into the ice maker mold for proper tray filling.
• Prevents water from dripping into the freezer compartment when intact.
• A cracked, warped, or missing fill cup can cause underfilled ice cubes, overflowing molds, or water pooling in the freezer.
• Compatible with common top/front-mounted household ice makers that use a separate plastic fill cup.

• Disconnect power and shut off the water supply before starting work.
• Remove the ice bin or ice maker assembly as needed to access the fill cup.
• The cup typically snaps or slides into place; use gentle pressure and avoid forcing plastic tabs.

This leveling leg supports and stabilizes the refrigerator cabinet. Adjusting it keeps the unit level so doors align and seal correctly, helping reduce vibration and noise for smoother, more reliable performance.

• Threads into the base to support and level the appliance
• Allows height adjustment for proper door alignment and gasket contact
• Helps reduce rocking, vibration, and rattling noises
• Resolve issues like doors not closing fully, uneven gaps, or a wobbly cabinet

• Disconnect power and move the appliance carefully to access the leg
• Use a helper and protect flooring; tip the unit slightly and support it securely
• Unthread the old leg; hand-thread the new leg, then adjust as needed with a wrench
• Level front-to-back and side-to-side; avoid cross-threading or overtightening

This plug button is a small snap-in cap used on refrigerators to cover exposed holes on door handles, liners, or trim. It restores a clean, finished look while helping keep dust and moisture out of the cabinet.

• Snaps into a screw or access hole on a handle, liner, or trim panel
• Covers fasteners and gaps for a clean, finished appearance
• Helps block dirt and moisture from open holes
• Typical symptoms: missing cap, broken or loose plug, visible screw hole or cosmetic gap

• Unplug the appliance before servicing and use caution around sharp edges
• Align the plug with the hole and press straight in by hand until fully seated and flush
• For handle screw holes, tighten fasteners first, then install the cap
• Avoid using metal tools on finished surfaces to prevent scratches

This reversible door plug is a small trim cap that fills the unused holes on a refrigerator door after changing the door swing. It restores a clean, finished look and helps keep dust and moisture out.

• Covers unused hinge/handle screw holes created during a door reversal
• Press-fit cap designed to match lighter gray door trim
• Helps maintain appearance and reduce entry of dirt and moisture
• Replace if missing, cracked, discolored, or won't stay seated

• Disconnect power if removing or repositioning the door/hinges
• Use your model's parts diagram to confirm the plug location and color
• Align with the hole and press in by hand until flush with the surface
• Do not force; verify correct part if the plug will not seat properly

This compressor start relay and overload is the start device for your refrigerator's compressor. It helps the motor start and protects it from overheating, supporting reliable operation when the original start components fail.

• Provides the initial boost to start the compressor via a PTC start relay
• Overload protector opens the circuit if temperature or current is excessive
• Common symptoms: compressor won't start and repeatedly clicks
• Warm or rising fresh food/freezer temperatures
• Compressor starts then stops after a few seconds

• Disconnect power and allow the compressor to cool before servicing
• Access the compressor compartment; note wire locations and device orientation
• Pull the old device straight off the compressor pins; press the new assembly fully onto the terminals and reconnect wires securely
• Inspect connectors for heat damage and replace any burned terminals before restoring power

This top hinge and pin assembly supports the refrigerator door at the upper corner and provides the pivot point for smooth opening and closing. Replacing a worn hinge restores proper alignment and a consistent, reliable door seal.

• Supports door weight at the top and provides the pivot for smooth swing
• Maintains door alignment to prevent rubbing and uneven gaps
• Helps the door close securely for proper gasket contact
• Typical symptoms: door sags or scrapes, doesn't close flush, binds/clicks at the top, visible wobble

• Disconnect power and remove items from the door shelves
• Have a helper support the door; remove the top hinge cover and mounting screws, then lift the door straight up/off
• Position the new hinge, secure with the original hardware, and set the door back on the pins
• Adjust leveling if needed before restoring power

The Handle Mount is an OEM component specifically designed for GE French door refrigerators. It serves as the attachment point for refrigerator door handles.

The handle mount connects the handle assembly securely to the refrigerator door itself. Its sturdy construction manages stress from frequent usage while allowing for smooth operation.

Symptoms of a bad handle mount include:

• Loose, unstable, or detached door handles
• Handles difficult-to-operate or open doors with  
• Visible bending, cracks, or damage to the mount
• Reduced grip strength or door control

Causes can involve normal wear over extended periods, imprecise impacts, or repeated stress from heavy handling exceeding the mount’s limits. 

Replace with this genuine GE OEM part to restore a tight, lasting connection between handles and doors. Compatible also with Hotpoint, RCA, and Kenmore French door refrigerator models.
 

This control knob fits onto the refrigerator's control shaft so you can turn and set temperature or other settings. Replace a cracked, stripped, or missing knob to restore smooth operation and reliable adjustments.

• Connects to the control shaft to adjust temperature or feature settings
• Provides a secure, correct fit to prevent slipping or free-spinning
• Restores the ability to set and read the desired level
• Common symptoms: broken/cracked knob, knob won't stay on, spins freely, can't change settings

• Disconnect power to the refrigerator before servicing
• Pull the old knob straight off; gently wiggle if needed—avoid prying on the panel
• Align the flat/D-shaped opening with the control shaft and press on until fully seated
• Turn the control to verify smooth operation and proper alignment with markings

This cable clamp secures refrigerator wiring to the cabinet, keeping harnesses organized and protected. Replacing a missing or damaged clamp helps prevent chafing and vibration noise while maintaining proper clearance from fans and other moving components.

• Anchors wire harnesses in their designed routing
• Helps prevent insulation wear from rubbing or vibration
• Keeps wires clear of sharp edges and moving parts
• Common signs it's needed: missing/broken clamp, loose or dangling wires, or new rattling/buzzing noises

• Disconnect power before servicing
• Access the clamp location and note original wire routing
• Position the clamp and secure with the existing fastener; do not overtighten
• Ensure wires aren't pinched and have clearance from the fan/compressor before restoring power

This vinyl sleeve fits over a rod, tube, or wire in the refrigerator to protect and cushion contact points. It reduces wear and vibration and helps keep components aligned for smooth, reliable operation.

• Provides a protective barrier at contact points to prevent abrasion or marring
• Helps maintain spacing and alignment for a snug, proper fit
• Cushions to damp vibration and reduce rattles or squeaks
• Replace if the sleeve is missing, cracked, hardened, or if components feel loose or make noise

• Disconnect power; turn off the water supply if working near water lines
• Note the sleeve's original location and orientation; take a photo for reference
• Remove the old sleeve and any debris; slide the new sleeve into the same position
• Check clearance and resecure related parts before restoring power

This is a refrigerator freezer door assembly that is stainless steel in color. This part includes the inner liner and the outer panel. Additional parts may be included. This is only the top freezer door. The door is very heavy and may require two people to lift it safely.A new refrigerator freezer door will be needed if it becomes dented or otherwise damaged in any way. This can happen if a sharp and heavy object makes a forceful impact on the door and dents it. Even if the door is operating properly, the owner may choose to replace it for cosmetic reasons. Be careful when lifting the original freezer door off of the hinges so that it isn't dropped, which could damage flooring or injure someone.As a genuine OEM part, it comes directly from the manufacturer. It is sold individually. This refrigerator freezer door is compatible with appliances that are manufactured by GE.

Size: 10-16 ab.