Frs6hf6jqo Parts

This refrigerator light socket holds and powers the interior bulb so you can clearly see inside. Replace a cracked, heat-damaged, or loose socket to restore reliable illumination when the interior light won't work or flickers.

• Provides the electrical connection and mounting point for the compartment light bulb
• Fixes symptoms such as no interior light with a known-good bulb
• Addresses intermittent flickering when the door is opened or closed
• Helps resolve visible charring, melting, or broken contacts on the socket
• Corrects a loose bulb that won't stay seated or lit

• Disconnect power to the refrigerator before servicing; remove the light lens/cover and bulb
• Note wire positions; release the old socket from its mount
• Transfer wires to the new socket one lead at a time and seat the socket fully
• Reinstall the bulb and cover; restore power and test
• Use only the bulb type and wattage specified for your model

The Light Switch is an OEM part for Frigidaire refrigerators. It is designed to control the interior lighting of the refrigerator; the switch activates when the door is opened and deactivates when closed. 

Causes of a bad Light Switch can include mechanical wear from frequent use, which may cause the switch to fail to engage or disengage properly. Electrical issues such as short circuits or loose connections can also prevent the switch from functioning correctly.

Symptoms of a bad Light Switch include:

• The refrigerator light staying on when the door is closed
• The light not turning on when the door is opened
• Flickering or intermittent lighting when the door position changes

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Nylon

The Door Light Switch is an OEM part for Frigidaire refrigerators. It is a component located inside the refrigerator door that turns the interior light on and off based on door position. The light switch works with a door switch plate and light socket assembly to automatically illuminate the interior when the door is opened.

Causes of a bad switch can be normal wear and tear over time, especially from frequent door openings. The contact points within the switch can become corroded or damaged.

Symptoms of a bad light switch include:

• Interior light not turning on at all when door is opened
• Light remaining constantly on even when door is closed
• Inconsistent or intermittent lighting

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
 

This spacer fits between the fixed crusher blades inside the refrigerator's ice bucket assembly. It preserves the correct gap and alignment so the auger turns freely and crushed ice dispenses smoothly without jams or grinding.

• Maintains the correct spacing between fixed crusher blades in the ice bucket
• Keeps the blade stack and auger aligned for smooth rotation
• Helps prevent ice jams, grinding noises, and inconsistent crushed-ice output
• Replaces a worn, cracked, or missing spacer discovered during service

• Disconnect power before servicing; remove the ice bucket from the freezer door/bin
• Carefully disassemble the crusher housing, noting the exact order of blades, spacers, and washers
• Wear cut-resistant gloves; crusher blades are sharp
• Reassemble in the original sequence and verify the auger turns freely before reinstalling

This cover assembly replaces a damaged or missing cover on your appliance, protecting internal components and restoring a clean, finished appearance. Use it when the original is cracked, loose, or no longer secures properly.

• Shields internal parts from debris, spills, and accidental contact
• Helps keep components enclosed and aligned for reliable operation
• Restores the appliance's finished look after damage or wear
• Common signs of failure: cracks, broken or missing tabs, discoloration, rattling, or a cover that won't stay in place

• Disconnect power before servicing; shut off water supply if working near water connections
• Remove retaining screws or release tabs; note the orientation of the original cover
• Transfer and reuse original screws, clips, or seals if required
• Do not overtighten fasteners into plastic; ensure all tabs fully engage before testing

Kit includes ice and water actuator arms.

This evaporator fan motor mounting bushing isolates the motor from its bracket to reduce vibration and rattling. Replacing a worn bushing helps keep the fan secure and centered so airflow remains smooth and operation is quieter. What it does:

• Cushions and isolates the evaporator fan motor to reduce vibration and noise
• Helps maintain motor alignment to prevent the fan blade from rubbing the shroud
• Secures the motor to the mounting bracket
• Typical symptoms: rattling or buzzing from the freezer, fan wobble, loose motor, or a cracked/missing bushing

• One motor mounting bushing

• Unplug the refrigerator before servicing and wear safety gloves
• Remove the freezer back panel/evaporator cover to access the fan motor
• Support the motor, remove fasteners, and transfer/install the bushing on the bracket/motor as shown in your service diagram
• Ensure the bushing is fully seated and the fan blade spins freely with proper clearance before reassembly

This position-specific ice crusher blade (#1) fits inside the refrigerator's ice bucket assembly. It helps break up cubes into crushed ice; replacing a bent or worn blade restores consistent crushing and reduces jams or grinding noises during dispensing.

• Works with the auger and other numbered blades to crush ice when "Crush" is selected
• A bent, dull, or corroded blade can lead to no crushed ice, only cubes, slow dispensing, or scraping/grinding noises
• Restores even crushing and smoother auger rotation
• Position- and orientation-specific within the blade stack; match to your original

• Disconnect power and switch the ice maker OFF before servicing
• Remove and empty the ice bucket; allow any frost to thaw
• Disassemble the bucket front/auger and note the exact blade order and orientation—take photos for reference
• Wear cut-resistant gloves; reassemble blades, spacers, and washers exactly as removed and verify the auger turns freely before reinstalling

The defrost drain pan collects water that melts off the evaporator during automatic defrost and holds it near the warm compressor so it can evaporate. Replacing a damaged pan helps prevent leaks, puddles, and odors around the base of the refrigerator.

• Collects defrost water routed from the evaporator drain
• Positions water in warm airflow near the compressor for evaporation
• Replace if the pan is cracked, warped, missing, or leaking
• Symptoms can include water on the floor, moisture under the unit, or musty odors

• Unplug the refrigerator; wear cut-resistant gloves
• Pull the unit forward and remove the lower rear access panel to reach the pan near the compressor
• Lift out the old pan; transfer any reusable clips/brackets; seat the new pan under the drain tube and ensure it's level and clear of moving parts
• Reinstall the panel, restore power, and check for proper drainage and evaporation

This replacement screw secures refrigerator components such as brackets, trims, and covers. Replace missing or stripped hardware to keep parts tight and aligned, helping eliminate rattles and restoring a solid, reliable fit.

• Fastens interior or exterior components to the cabinet or doors
• Replaces missing, rusty, or stripped hardware
• Helps reduce vibration noises from loose parts
• Restores proper fit and alignment of panels, trims, or covers

• Disconnect power; turn off water supply if working near the dispenser or ice system
• Retain and reuse any original spacers or washers
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace one fastener at a time to maintain alignment

This is the drive gear for the ice maker module. It transfers motor power to the ejector/harvest mechanism so cubes release consistently; worn or stripped teeth can cause clicking, stalls, or little to no ice production.

• Transfers motor torque to rotate the ejector and complete the harvest cycle
• Replaces a cracked, stripped, or worn gear that prevents proper ice ejection
• Typical symptoms: no ice production, icemaker stuck mid-cycle, clicking or grinding from the module
• Helps restore reliable ice maker cycling

• Unplug the refrigerator before service; turn off the water supply if moving the icemaker
• Remove the icemaker assembly for access; note the original gear's orientation before removal
• Align the new gear with the shaft; do not force it—inspect mating parts for wear
• After reassembly, verify the ejector turns freely; restore power and run a test cycle

This ice crusher blade (#2) mounts in the freezer's ice bucket assembly. It helps break up cubes for the Crushed Ice setting and can restore smooth dispensing when the original blade becomes bent, dull, or broken.

• Mounts inside the ice bucket crusher to slice/crush cubes when Crushed Ice is selected
• Helps maintain consistent ice flow and size through the dispenser
• Wear or damage may lead to no crushed ice, only whole cubes dispensing, jamming, or grinding noises
• Visible bending, dull edges, or a missing blade are common failure signs

• Disconnect power and remove the ice bin from the freezer
• Disassemble the crusher housing to access the blades; note the order/orientation of blade #1 and blade #2 before removal
• Wear cut-resistant gloves—edges are sharp
• Reassemble in the same order, tighten fasteners, reinstall the bin, and test the dispenser

This clip mounts to the refrigerator liner and secures the crisper cover/slide rail so the drawer stays supported and glides properly. Replace a broken or missing clip to restore alignment and smooth operation of the crisper.

• Holds the crisper cover/slide rail firmly against the cabinet liner
• Supports the crisper drawer to prevent sagging or tilt
• Helps restore smooth opening and closing of the crisper drawer
• Common symptoms of failure: loose rail, drawer off-track, difficulty sliding, or a cracked/missing clip

• Unplug the refrigerator or disconnect power before servicing
• Remove the crisper drawer and cover/glass to access the clip
• Release the old clip (snap tabs or screw), align and secure the new clip; reuse the original fastener if your model uses one
• Reinstall the cover and drawer; the drawer slides freely

The Switch-4 Button Assembly is an OEM part for Frigidaire refrigerators. This switch assembly operates important refrigerator functions like the light controls, temperature selection, and ice/water dispenser functions. It contains four precise switches designed to last through years of use while maintaining accurate input control.

Causes of a bad switch assembly can include continuous actuations over time leading to switch wear, accidental damage or spills compromising switch integrity, or failures in electronic components.

Symptoms of a bad switch assembly include:

• Lights or temperature settings not functioning properly
• Ice/water dispenser buttons not working as expected
• Failed or improperly actuating switches
• Water leaks or electrical issues at the switch location

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This ice crusher blade (#3) fits inside the refrigerator's ice bin crusher stack. It helps break cubes into crushed ice when selected, restoring smooth, consistent crushed-ice dispensing if the original blade is bent, dull, or missing. What it does:

• Works within the ice bin's crusher assembly to fracture cubes into crushed ice
• Engages with the auger and spacers as part of the blade stack
• Worn or damaged blades can lead to only cubes dispensing, weak crushing, jams, or scraping noises
• Visible bending, chips, or rust are common signs it needs replacement

• One crusher blade (#3)

• Disconnect power and remove the ice bin before service
• Empty the bin and carefully disassemble the crusher stack; note the exact order and orientation of blades, spacers, and washers
• Wear cut-resistant gloves—blade edges are sharp
• Reassemble in the same sequence and verify the assembly turns freely before reinstalling the bin and restoring power