Gaffers Sattler Parts

This evaporator wire harness routes power and signals to the freezer evaporator components so the cooling and defrost systems operate correctly. It replaces a damaged or disconnected harness to restore circuit connections behind the evaporator. What it does:

• Provides electrical connections to evaporator components such as the defrost heater, thermostat/thermistor, and fan motor
• Ensures consistent signaling for defrost cycles and evaporator fan operation
• Helps stop symptoms like a warm freezer, intermittent cooling, or failed defrost when caused by wiring faults
• Maintains proper routing and secure connector fit to prevent shorts or intermittent contacts

• One evaporator wire harness assembly

• Disconnect power to the appliance before starting any repair
• Remove evaporator cover panels carefully; avoid bending evaporator fins
• Match connector shapes and routing to the original harness; secure away from moving parts

Size: 1/4 lb.

Size: 1/4 inch.

Size: 6 - 20 x 1 1/16 inch.

This drive coupler connects the washer motor to the transmission so the agitator or drum turns smoothly. It's a direct-replacement part that restores drive engagement when the original coupler is worn or damaged. What it does

• Transfers motor rotation to the transmission/agitator so the tub agitates or spins.
• Commonly replaced when the washer won't agitate, spin, or makes grinding or clunking noises.
• Resists normal wear from torque and repeated use; failure causes slipping or loss of drive.
• Helps prevent further damage to the motor or transmission when replaced at first signs of wear.

• One drive coupler

• Disconnect power and water supply before beginning any repairs.
• Access typically requires removing the cabinet or front panel; follow the manufacturer service manual.
• Inspect motor shaft and transmission input for damage when replacing the coupler.
• If transmission or motor splines are damaged, replace the damaged assembly rather than relying on a new coupler.

This perimeter door gasket seals the refrigerator compartment, helping keep cold air in and humid room air out. Replacing a worn or torn gasket restores a tight seal for better temperature stability, reduced frost and condensation, and efficient operation.

• Creates an airtight seal when the door closes to maintain set temperatures
• Helps prevent moisture, sweating, and frost buildup around the door opening
• Reduces warm-air infiltration so the unit doesn't run as long or as often
• Common symptoms include tears, warping, gaps, persistent condensation, or doors that won't seal

• Disconnect power before servicing
• Lay the new gasket flat to relax; warming with hot water or low heat can help remove kinks—do not overheat
• Remove the old gasket and press the new one fully into the retainer/channel, starting at the corners and working around
• Close the door and check for uniform contact all around; adjust door alignment if needed and recheck the seal (paper "dollar bill" test)

The Drain Tube is an OEM part for Whirlpool-brand French door refrigerator water dispensers and ice makers. It channels excess water away during the icemaking process. 

Causes of a bad drain tube can include mineral buildup clogging the narrow opening over time or cracks developing from rigid ice contact every cycle.

Symptoms of a bad drain tube include:

• Water failing to properly drain away from the ice maker
• Puddles or leaks appearing near the freezer floor   
• Ice production deteriorating due to water backup
• Mineral scale deposits accumulating around connections

Replacing it with this OEM tube restores full water ejection to produce clean ice. Also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore refrigerators.

This wire harness is a factory-style wiring assembly designed to restore reliable electrical connections between major appliance components. It helps ensure consistent power and signal routing for proper operation and safety. What it does:

• Routes power and control signals between components to enable normal appliance functions
• Replaces damaged, burned or frayed wiring that can cause intermittent operation
• Can resolve symptoms such as components not powering, controls not responding, or cycles failing to start
• Provides original-style connector ends and wire routing for a plug-and-play fit when installed correctly

• Disconnect power (and gas if applicable) before beginning any repair
• Compare the new harness to the old one to confirm connector types and lengths before installing
• Route and secure the harness following original cable paths and mounting points to avoid chafing or heat exposure
• If wiring or connector damage is extensive, inspect associated components and replace as needed.

This is a replacement 8-18 threaded screw used to secure panels and components on compatible Whirlpool appliances. It restores proper fastening where a missing or damaged screw causes loose parts or vibration. What it does

• Fastens panels, brackets, and small assemblies to the appliance frame
• Replaces stripped, corroded, or missing screws that cause rattling or loose components
• Helps maintain proper alignment of panels and controls for safer operation
• Suitable where an 8-18 threaded machine screw is specified by the manufacturer

• One replacement screw

• Disconnect power to the appliance before service to prevent shock or injury
• Use the correct driver to avoid stripping the screw head; do not force mismatched tools
• Tighten until snug — avoid over-tightening which can strip threads or crack plastic
• If replacing multiple fasteners, check mating threads and replace any damaged clips or anchors as needed