Gdf530pgmobb Parts

This leveling leg adjusts the dishwasher's height at the base, helping you level and stabilize the unit inside the cabinet. Proper leveling reduces rocking and vibration and promotes a tight door seal and smooth rack operation.

• Screws into the base frame to set height and level the dishwasher
• Supports the unit to prevent rocking or wobbling
• Helps maintain door alignment and sealing; poor leveling can contribute to leaks
• A worn, bent, or missing leg can make leveling difficult and increase vibration/noise

• Disconnect power and shut off water; slide the dishwasher out if needed for access
• Turn the leg with a wrench or pliers to adjust height; replace by threading the new leg into the base
• Use a bubble level to set side-to-side and front-to-back level before re-securing the unit
• Do not overtighten; ensure both legs carry weight evenly on a solid floor surface

The Vent Filter is an OEM part for GE dishwashers. It helps to capture and filter out food particles, grease, and other debris. 

Causes of a bad vent filter can include clogging or blockage due to accumulated debris, wear and tear over time, or damage to the filter material.

Symptoms of a bad vent filter include:

• Lingering unpleasant odors during or after the dishwasher cycle
• Visible signs of debris or buildup on the filter surface
• Reduced effectiveness of the dishwasher's drying performance

Replace your worn-out or clogged vent filter with this genuine OEM GE part to restore your dishwasher. 

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

Rack bracket with three wheels for the dishwasher rack. This assembly mounts to the rack and rides in the rail to keep the rack level and rolling smoothly, replacing cracked wheels or a damaged bracket to restore easy operation.

• Supports the rack and rolls along the rail on three wheels
• Restores smooth in-and-out rack movement
• Helps keep the rack aligned and prevents derailing or dropping
• Typical failure signs: cracked/broken wheels, damaged bracket, rack binding

• Disconnect power at the breaker; shut off water supply for safety
• Pull the rack out and remove any rail end caps/stops to access the bracket
• Release the old bracket and install the new one in the same orientation
• Reinstall stops, reseat the rack, and verify smooth travel

This dishwasher junction box cover encloses the power-connection compartment at the base of the unit. Replacing a damaged or missing cover helps protect wiring from debris and accidental contact, restoring a safe, secure connection area. What it does:

• Covers and secures the dishwasher's electrical junction box
• Helps shield wire splices from moisture, dust, and accidental contact
• Restores proper fit when the original cover is cracked, broken, or missing
• Useful if the junction box won't stay closed or the cover no longer secures properly

• Includes 1 junction box cover

• Disconnect power at the circuit breaker before servicing
• Remove the lower access/kick panel to reach the junction box
• Remove the old cover and screw, position the new cover, and secure with the existing hardware
• Ensure all wiring and the strain relief are fully inside the box before closing; restore power and test

The Sump Overmold Service Kit is an OEM part for GE dishwashers. It includes the sump and filter assembly that collects food debris and drains water at the bottom of the dishwasher. This over-molded, tightly-sealed design removes soils and prevents leaks. 

Causes of failure can be cracks, chips, or splits to the sump overmold due to excessive mineral buildup, high heat, or other wear over time. Foreign objects entering the sump area may also damage the filter mesh.

Symptoms of a faulty sump over mold assembly include:

• Standing water at the bottom of the dishwasher  
• Water leaks during or after the cycle
• Poor draining or poor rinsing performance
• Grime or food debris stuck to dishes

This genuine GE part is compatible also with Hotpoint, RCA, and select Kenmore brands.

This Roller and Bracket Assembly is an OEM part for GE dishwashers. It is an essential component in the dishwasher's rack system, providing smooth and stable movement for the racks as they slide in and out. This assembly includes both the rollers and the brackets that attach them to the dishwasher racks, ensuring effortless gliding and reliable support. 

The need to replace the roller and bracket assembly can arise from wear and tear, damage, or misalignment. 

Symptoms of a faulty Roller and Bracket Assembly include:

• Difficulty in sliding the racks in and out smoothly.
• Racks getting stuck or derailing during movement.
• Noticeable wear or damage to the rollers or brackets.
• Unusual noises when moving the dishwasher racks.
• Loosening or detachment of the assembly from the racks.

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

The Housing UI Board is an OEM part for GE dishwashers. This housing ensures that the electronic components within the UI board are shielded from environmental factors such as moisture, heat, and physical impact, which could otherwise lead to malfunctions. 

Causes of a bad Housing UI Board can include physical damage from impacts or accidents, wear and tear from frequent use, or warping due to exposure to high temperatures or moisture.

Symptoms of a malfunctioning Housing UI Board include:

• Difficulty in operating the dishwasher controls
• Visible damage or cracks on the housing that could allow moisture or debris to affect the UI board
• The dishwasher failing to respond to input from the control panel

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Configured Machine Control Board is an OEM part for GE dishwashers. As the central processing unit, it operates all wash cycle functions and ensures communication between electronic components.

Symptoms of a failed control board include:

• Fault codes displayed
• Non-responsive buttons and displays  
• Inability to initiate or advance cycles
• Drainage, heating or motor errors

Causes can be physical damage, electrical surges compromising electronics, or simply wear over time degrading circuitry performance. 

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This right-hand rack slide and end cap assembly guides and retains the dishwasher rack on its track. Replacing a worn assembly restores smooth rack travel and helps prevent the rack from over-extending or dropping on the right side.

• Provides the right-side slide track for the dishrack and includes the built-in end-cap stop
• Maintains rack alignment for smooth in-and-out movement
• Replace if the slide is bent or the stop/end cap is cracked or missing
• Typical symptoms include the rack falling off the track, over-extending, binding, or sitting unevenly on the right side

• Disconnect power at the breaker and turn off water if moving the appliance for access
• Pull the rack out; support it before removing the existing slide
• Remove any mounting screws or release locking tabs to detach the old slide; transfer hardware if required
• Position and secure the new right-hand slide; ensure the end cap locks, then test rack travel

This clamp kit replaces worn Piranha-style clamps used in the dishwasher's wash system. Restores a tight, reliable seal on internal connections to help prevent leaks and maintain proper water circulation for consistent cleaning results.

• Secures internal hose and pump connections within the wash system
• Helps stop water leaks caused by loose, stretched, or damaged clamps
• Supports proper circulation and wash performance by keeping joints sealed
• Common symptoms: water under the unit, drips at hose joints, loose connections, vibration or rattling from the sump area

• Disconnect power and shut off the water supply before servicing
• Access the sump/pump area from the front toe-kick or by pulling the unit out as needed
• Replace one connection at a time; position and fully seat the new clamp(s) on clean hose/barb surfaces
• Restore power/water and run a short cycle to check carefully for leaks before reinstalling panels

This replacement O-Ring restores a watertight seal at an internal dishwasher connection, helping stop leaks and protect surrounding cabinetry. Replace a hardened, cracked, or flattened seal to maintain reliable wash performance and prevent water damage.

• Creates a watertight seal between mating parts inside the dishwasher
• Helps prevent drips and leaks during fill, wash, and drain cycles
• Addresses leaks caused by a worn, flattened, or damaged seal
• Visual clues: cracks, brittleness, deformation, or mineral trails at the joint

• Disconnect power and shut off the water supply before servicing
• Access the affected connection and remove the old O-ring
• Clean the groove and mating surfaces; lightly lubricate with food-grade silicone grease; seat evenly without twisting or pinching
• Reassemble and run a brief test cycle to check for leaks

This upper wash impeller circulates water to the upper spray system during the wash cycle, helping deliver thorough cleaning across dishes on the upper rack and throughout the tub.

• Drives water flow to the upper spray arm/manifold
• Worn or damaged impeller can cause weak spray, poor cleaning, or longer cycle times
• Physical damage (warping, cracks, stripped splines) warrants replacement

• Disconnect power and water before servicing
• Access is typically through the sump/pump area; note impeller orientation during removal
• Inspect mating parts (seal, hub, shaft/splines) and replace if worn
• Hand-tighten fasteners to OEM guidance and verify free rotation before reassembly

Size: 8-18 AB TSQ 5/8 SS

This is a machine screw used to secure dishwasher components. The 10-32 thread and 3/8-inch length with an integrated hex washer head provide a firm, vibration-resistant hold to keep parts properly fastened.

• Secures brackets, panels, or internal assemblies in the dishwasher
• Helps prevent looseness, rattling, or misalignment during operation
• Common symptoms of a missing/stripped screw include panel movement, vibration, or loose mounting points

• Disconnect power and shut off water before servicing
• Use the correct nut driver or socket to avoid stripping the head
• Replace any damaged or missing screws in matching locations
• Do not overtighten; snug to manufacturer's torque guidance when available

The Funnel Service Kit is an OEM replacement part for GE dishwashers. It includes a water inlet funnel and seals necessary for proper water flow within your dishwasher. This part helps prevent leaks and ensures that water is properly directed into the dishwasher.

Symptoms of a faulty water inlet funnel service kit include:

• Water leaks from the dishwasher
• Insufficient water flow during the wash cycle
• Inconsistent cleaning or rinsing performance

Causes of a bad water inlet funnel service kit can include wear and tear over time, blockage from debris or mineral buildup, or damage to the funnel or associated components. If you notice issues such as water leaks, inadequate water flow, or inconsistent cleaning results, it may be time to replace the old or damaged water inlet funnel service kit with this genuine OEM part.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.