Gdf570ssjoss Parts

This wiring harness assembly connects and routes power and control signals for the appliance's AC components, restoring reliable electrical connections and proper operation when the original harness is damaged or worn. What it does:

• Provides the factory wiring path for AC-related components so they receive correct power and signals
• Replaces frayed, damaged, or burnt wires that can cause intermittent operation or failures
• Helps eliminate symptoms such as components not powering on, intermittent operation, or electrical arcing at connections
• Ensures connector fit and terminal alignment for a secure electrical connection

• Disconnect power before beginning any repair to avoid electrical shock
• Note or photograph wire routing and connector positions before removal for correct reinstallation
• Secure harness with existing clips or fasteners to prevent chafing and strain on terminals

This rubber grommet provides a protective seal where hoses, wires or components pass through openings, helping prevent chafing and moisture intrusion. Use it to restore a tight fit and reduce wear at the penetration point. What it does:

• Seals and cushions openings to help prevent water leaks and air gaps.
• Protects wiring and hoses from rubbing on sharp metal edges that can cause wear or shorts.
• Reduces vibration and rattling by holding parts securely in place.
• Common symptoms of failure: visible cracking, missing or torn grommet, water dripping near the opening, or rubbing noises.

• Disconnect power to the appliance and turn off water supply before beginning any repair.
• Remove the access panel or boot as needed to reach the opening; press the grommet into the hole until fully seated.
• Inspect surrounding seals, hoses and wiring; replace any damaged components to prevent repeat issues.

This SCR 8-18 silicon-controlled rectifier replaces the control semiconductor that switches and regulates power to heating or motor circuits in compatible appliances, restoring proper power delivery and control. It's a direct-fit electrical replacement part. What it does

• Acts as a switching device on control boards to allow or block current flow when signaled.
• Regulates power delivered to heating elements or motor circuits to enable proper operation.
• Commonly linked to symptoms like no heat or intermittent heating, motors that won't start, or erratic control-board behavior.
• Helps restore reliable on/off control when a failed SCR is causing open or shorted conditions.

• One SCR 8-18 silicon-controlled rectifier (WD02X10160).

• Always disconnect power before servicing the appliance to avoid shock.
• Handle the part carefully; avoid touching leads and use anti-static precautions if available.
• Inspect surrounding connectors and wiring for damage; replace any corroded terminals.

This control box bottom is the lower housing piece that secures and protects the appliance control board and related components. It restores a stable mounting surface and helps keep electronics shielded from vibration and debris. What it does:

• Provides the lower half of the control box housing to support and protect the control board
• Keeps wiring and connectors routed and held in place to prevent strain
• Replaces cracked, broken or warped housing that can expose electronics
• Helps stop rattling or movement of the control assembly that can cause intermittent controls

• Control box bottom

• Power off and unplug the appliance before starting any repair
• Handle the control board and connectors carefully to avoid electrostatic or mechanical damage
• This part typically installs with screws or clips; retain fasteners and note their locations during disassembly
• Inspect and address the electronics before reassembly

A silicon-controlled rectifier (SCR) used on appliance control boards to regulate power to motors, igniters or other loads. Replacing a faulty SCR can restore proper power switching and steady operation of the driven component. What it does:

• Acts as a power-switching semiconductor in appliance electronic control circuits to allow current flow only when triggered.
• Enables controlled delivery of voltage/current to motors, igniters and similar loads on the control board.
• A failing SCR can cause symptoms such as no power to a motor or igniter, intermittent operation, or complete failure of the driven component.
• Match the SCR package and electrical ratings to the control board before replacing.

• Disconnect all power to the appliance before accessing control electronics to avoid shock or damage.
• Take electrostatic-discharge (ESD) precautions; handle the SCR by its body and avoid touching leads.
• Package orientation and electrical ratings on the control board and wiring before installation.

This is a stainless steel hex washer-head screw used to fasten and secure components. Its integrated washer head provides a broad bearing surface for a tight, durable hold in appliance assemblies.

• Secures panels, brackets, and hardware to prevent looseness and vibration
• Restores proper fastening when originals are stripped, missing, or corroded
• Stainless construction helps resist rust in moisture-prone areas
• Common symptoms of a needed replacement include rattling, loose panels, or missing hardware

• Disconnect power and, if applicable, shut off water before servicing
• Use the correct nut driver or socket for the hex head to avoid stripping
• Replace any damaged or missing fasteners in matched pairs or sets for even clamping
• Do not overtighten; snug to manufacturer torque guidance when available

This foam vent insert seals and cushions the dryer vent opening to reduce airflow leaks, vibration noise, and lint bypass. It helps maintain proper venting and stops drafts for more efficient drying and quieter operation. What it does:

• Forms a compressible seal around the dryer vent outlet to limit air and lint escape
• Cushions the vent connection to reduce rattling and vibration noise
• Helps prevent drafts from entering the cabinet when the dryer is off
• Supports consistent airflow path for better drying performance

• Designed for snap-in or press-fit installation at the vent opening; your model diagram for location
• Turn off and unplug the appliance before accessing the vent area
• Inspect surrounding vent and ductwork for damage or excessive lint; replace if needed

This floor plate is the OEM-style replacement that fits under the oven cavity to protect internal components and provide a stable cooking surface. Restores proper support and helps maintain even heat distribution in the lower oven area. What it does

• Covers and protects the oven's lower cavity from spills, drips, and falling debris
• Helps funnel heat and airflow for more consistent baking and roasting performance
• Prevents direct contact between food/drips and heating components
• Reduces corrosion and wear to inner oven parts caused by spills

• One floor plate as shown

• Designed to be installed in the lower oven cavity; for exact placement
• Remove power (unplug or shut off breaker) and allow the oven to cool before servicing
• Use appropriate gloves to avoid sharp edges; avoid forcing the part into place

This block foam door is an insulated panel that fits inside the appliance door to help reduce heat transfer and maintain consistent internal temperatures. It restores door insulation for more efficient cooling and temperature stability. What it does:

• Provides thermal insulation inside the door to reduce heat gain or loss
• Helps prevent frost buildup and cold spots by improving temperature consistency
• Supports efficient compressor cycling and can reduce energy waste when functioning properly
• Common symptom: uneven temperatures, visible condensation or frost on the door, or reduced cooling performance

• One block foam door

• Disconnect power before servicing and follow the appliance manufacturer's disassembly instructions
• May require removing the inner door liner and fasteners to access and replace the foam; keep hardware for reassembly
• Handle carefully to avoid damaging the foam or door liner; use appropriate hand protection

This latch cam engages the door latch mechanism so the appliance door closes and stays secure during cycles. A worn or broken cam can prevent the door from latching or cause the door to feel loose. What it does

• Rotates with the latch to lock the door securely during operation
• Ensures the latch striker catches and holds the door closed
• Common symptom: door won't stay latched or appliance won't start
• Common symptom: door feels loose, noisy, or intermittently opens during cycles

• One latch cam

• Disconnect power before starting any repair to avoid shock or injury
• Inspect surrounding latch components and replace any visibly damaged parts
• Use basic hand tools; keep track of small fasteners and alignment during reassembly
• Test door operation several times after installation to ensure secure engagement

This silicone light pipe guides an appliance's indicator or control panel light to the front-facing bezel so lights appear bright and centered. It restores proper light transmission for clearer, easier-to-read controls. What it does:

• Transmits LED or bulb light from the lamp housing to the control surface or bezel
• Helps ensure indicator lights and touch-control icons appear centered and visible
• Commonly replaced when the lens is cracked, torn, missing, or deformed
• Can resolve symptoms like dim, distorted, or missing panel illumination

• Disconnect power before servicing any electrical or control components
• Remove the control panel or bezel per your model's service instructions to access the light pipe
• Handle the silicone gently—avoid stretching or pinching that could deform the part
• Ensure the light pipe is fully seated in its housing and the bezel is reinstalled to prevent light leaks

Replacement control box top that restores the protective cover for the appliance control housing, keeping wiring and electronics enclosed for a cleaner appearance and safer operation. What it does:

• Covers and protects the control housing and internal wiring from dust, spills, and accidental contact
• Helps secure control components in place and maintain the appliance's factory appearance
• Commonly replaced when the original cover is cracked, broken, missing, or shows visible damage
• Can prevent loose wiring from catching or being accidentally disturbed

• One control box top

• Disconnect power to the appliance before beginning any work to avoid shock or injury
• Remove any screws or retainers securing the existing cover and lift off the old top; keep fasteners if reinstalling
• Align the replacement top and secure with the original fasteners; ensure wiring is routed and seated before closing

This replacement lower dishrack restores smooth rolling and secure loading on the bottom level of your dishwasher, helping plates, bowls, and pots stay in place for consistent spray coverage and reliable cleaning results. What it does

• Organizes and supports dishes, cookware, and utensils on the lower level during wash and dry cycles
• Rolls in and out on the tub rails for easy loading and unloading
• Positions items for effective spray coverage and drainage
• Replace if tines are broken, coating is peeling/rusting, the rack derails or won't roll smoothly, or items tip over

• One lower dishrack

• Turn off power to the dishwasher before servicing
• Pull the old lower rack straight out; release/remove any rack stops if present
• Transfer any removable accessories from the old rack (such as utensil basket or clips), if needed
• Slide the new rack onto the rails and verify smooth operation

This high loop drain hose creates the required elevated drain loop to help prevent dishwasher backflow and ensure proper drainage. It replaces a worn or damaged drain loop and restores correct drain routing for reliable performance. What it does:

• Forms the high loop in the dishwasher drain line to reduce risk of sink water siphoning back into the appliance
• Directs wastewater from the dishwasher into the household drain properly
• Helps avoid intermittent draining issues caused by a collapsed or split drain loop
• Fits into existing drain connections—used where an elevated drain loop is required

• Designed for in-line replacement; route the hose to create a high loop secured under the countertop or cabinet as shown in the appliance installer instructions
• Turn off power and water supply to the appliance before performing service
• Inspect clamps and fittings and replace if corroded; ensure all connections are snug but not over-tightened

The Turbidity Sensor is an OEM part for GE dishwashers. It is a water quality monitor that detects small food particles in the rinse water during dishwashing cycles. The sensor plays an important quality control role by ensuring water has achieved the necessary clarity before terminating the rinse phase.

Symptoms of a bad turbidity sensor include:

• Incomplete or unsatisfactory rinsing results
• Cycles not advancing properly beyond the rinse stage
• Error codes related to turbidity detection

Causes can be mineral deposits interfering with the sensor's ability to transmit light through the water, or failure of the electronic components over time.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Rack Roller is an OEM component compatible with GE dishwashers. Located on the rack guide rails inside the washer tub, it facilitates smooth gliding of rack shelving in and out for easy loading and unloading. 

Causes of failure can include cracked/warped rollers from years of continual movement, accumulation of debris preventing free motion, or detachment of roller heads compromising installation.

Symptoms include:

• Difficulty fully extending or retracting racks  
• Off-tracking of shelving from left to right rails
• Scratches or damage to dishware from improper rack functioning 

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.