Gdp280edoww Parts

This fixed dishrack bracket secures one end of a rack component (such as a fold-down tine row), keeping it anchored during wash cycles. Replace a cracked or missing bracket to restore stable support and reliable rack function.

• Anchors a rack component to the dishrack in a fixed position
• Helps keep dividers/tines aligned so dishes stay upright
• Replaces a broken, worn, or missing bracket
• Symptoms may include loose or collapsing tines, dishes tipping, or visible bracket damage

• Unload and extend the rack; remove the rack if needed for access
• Release the locking tabs/clips and remove the damaged bracket
• Align the new bracket and snap/slide it fully into place until it locks
• Verify a secure fit and smooth rack movement; wear gloves to protect hands
• Some racks use both fixed and adjustable brackets—confirm the side you need before ordering

This dishwasher fill funnel guides water flow into the appropriate channel, helping ensure proper distribution during wash cycles. Replacing a warped or damaged funnel can prevent leaks and restore consistent spray performance.

• Directs water into the dishwasher's internal water feed path
• Helps maintain correct water pressure for spray arms
• Common failure signs: leaking at the funnel area, poor spray performance, residue on dishes, or misalignment with the water feed tube
• Physical damage, warping, or a loose fit are typical replacement indicators

• Disconnect power and turn off water supply before servicing
• Access from inside the tub; remove any retaining screws or clips
• Inspect and reuse existing hardware/seals if still in good condition
• After installation, run a short cycle and check for leaks or misalignment

Black

This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.

• Provides adjustable support at one corner of the appliance
• Helps level the unit for correct alignment with floor or cabinetry
• Reduces rocking, vibration, and rattling noises
• Replaces stripped, bent, cracked, or missing leg

• Disconnect power and, if applicable, shut off water before servicing
• Carefully support or brace the appliance to access the base safely
• Start the new leg by hand to avoid cross-threading; adjust height gradually
• Use a level to check side-to-side and front-to-back, then recheck after positioning

The Door Harness Assembly is an OEM part for GE dishwashers. It routes power to key sensors and components located on the dishwasher door, including the door latch and interior lighting system. 

Causes of a bad Door Harness can include cracked insulation, pinched or cut wiring, or broken wire terminals due to repeated bending at connection points during door opening/closing cycles.

Symptoms of a bad Door Harness include:  

• Door latch not functioning properly
• Interior lighting not turning on 
• Delayed door locking or failure to latch fully
• Cycles not starting unless the door is firmly shut

Replace yours today with this genuine OEM GE part to ensure a proper seal and power delivery to key door systems. This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This fill funnel hose directs incoming water from the inlet assembly into the tub through the fill funnel. Replacing a worn or cracked hose helps stop leaks and restores a reliable, sealed fill path for consistent wash performance.

• Carries water from the inlet assembly through the fill funnel into the tub
• Maintains a watertight path to prevent external leaks
• Symptoms of failure: dripping during fill, puddles beneath the unit, or visible cracks/splits in the hose
• A significant leak may lead to low water level or extended fill times

• Disconnect power and shut off the water supply before servicing
• Remove the toe-kick/kickplate; pulling the dishwasher forward may be needed for access
• Place a towel or pan to catch residual water; move clamps, remove the old hose, and fully seat the new hose on both fittings
• Re-secure clamps, restore water and power, and run a short fill to check for leaks before reinstalling panels

This control box top is the plastic cover that protects the appliance's control board and user controls while keeping the front of the console finished and safe. It helps prevent dust, moisture, and accidental contact with internal electronics. What it does

• Covers and protects the control board and internal wiring behind the console.
• Provides the mounting surface and openings for buttons, knobs or touch interfaces.
• Prevents dirt, lint, and moisture from reaching sensitive electronics.
• Restores a secure, finished appearance to a damaged or cracked console area.

• Always disconnect power to the appliance before beginning work to avoid electrical shock.
• Remove any bezel, screws or clips securing the old top and transfer any required mounting hardware or trim pieces.
• Handle the control board and connectors with care; avoid touching circuit components or bending contact pins.

Size: 8-16 x 2 inch ss.

This vent screen covers the dishwasher door vent, allowing steam to escape while blocking food particles and debris. Replacing a damaged or missing screen helps maintain proper airflow and can reduce moisture and odors around the vent area.

• Screens the door vent to keep debris out of the vent duct and fan path
• Maintains airflow for venting steam during the dry cycle
• A clogged, cracked, or missing screen may lead to moisture at the vent, odors, or reduced drying performance
• Replace if warped, broken, or lost during service

• Disconnect power to the dishwasher at the breaker before servicing
• Open the door and remove inner-door screws to access the vent assembly
• Remove the old screen, seat the new screen fully and evenly, then reassemble without overtightening
• Run a short cycle and check the vent area for proper airflow and moisture

Screw: 8-16 x 3/8 inch.

This is the screw used to secure the dishwasher spray arm assembly components together, helping keep the arm properly attached so it can rotate and distribute wash water effectively.

• Fastens the spray arm assembly components to prevent wobble or detachment
• A loose or missing screw can cause poor cleaning, noisy operation, or a spray arm that falls off
• Restores stable spray arm rotation and consistent wash coverage

• Disconnect power and shut off water before servicing
• Open the dishwasher, remove the lower rack, and support the spray arm to prevent damage
• Use the correct screwdriver and avoid overtightening to protect plastic parts
• Check spray arm for free rotation after installation

This small check ball helps control water flow inside the refrigerator's water/ice system to prevent backflow and ensure proper filling. It restores reliable water seating where valves or distributor ports use a ball-style check. What it does:

• Acts as a one-way seal to stop water from flowing backward into the supply line or valve bore
• Helps the ice maker and dispenser fill correctly by allowing water in but not back out
• Common symptom: intermittent or incomplete ice maker fills
• Common symptom: slow or continuous dripping from dispenser or valve area

• Shut off water supply and unplug the appliance before starting
• Small part — handle carefully and note orientation/seat before removal
• Inspect valve bores and seals for debris; clean area before installing new check ball

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

The Upper Rack Bracket Assembly is an OEM replacement part for GE dishwashers. It is located inside the dishwasher tub and functions to securely mount the upper dish rack. It allows for adjustable height positioning and prevents rack movement during washing.

Causes of a bad upper rack bracket assembly can include cracks or breaks in the mounting points, stripped screw holes allowing rack sway, or deformities preventing proper seating.

Symptoms of a bad upper rack bracket assembly include: 

• Loosening or detaching of the upper rack during the cycle  
• Restricted rack adjustment or inability to set desired height
• Noise or vibration from an unsecured rack vibrating against the tub

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Right-hand door trim that replaces damaged or worn outer trim to restore the door's appearance and protect the door edge. Fits the right side and matches OEM fit and finish for a factory look. What it does:

• Covers and protects the outer edge of the refrigerator/freezer door from chips, dents and wear
• Restores a finished appearance when original trim is cracked, broken or missing
• Holds the door edge trim in place and conceals mounting points and seams
• Common symptoms: visible cracks or breaks in right-side door trim, loose or missing trim, or cosmetic wear

• Disconnect power to the appliance before starting any repair
• Handle trim carefully to avoid scratching the finish or damaging clips

The Filter Coarse is an OEM component specifically designed for GE dishwashers. It refers to the screen installed before the wash pump that traps soil and food particles. Subject to continuous wear from both water circulation and collected debris, the filter mesh can worsen over time.  

Causes of a bad coarse filter include:

• Clogged perforations blocking drainage and reducing water pressure  
• Loose mounting clips releasing trapped soils back into wash water instead of tube drain 
• Stretched or warped mesh no longer shutting tight to form a watertight seal

Symptoms of a failed coarse filter include:

• Soil tracked throughout the dishwasher unseen 
• Excessive residue left on dishes after washing and rinsing cycles
• Puddling inside the tub or continuing sound of draining after the cycle ends

This GE replacement part is also compatible with some Hotpoint and RCA models.