Gdt655smjoes Parts

This control board clip secures the dishwasher's electronic control board to its mounting location, keeping it properly seated during operation. Replacing a damaged or missing clip helps prevent vibration, movement, and wire-connector strain.

• Holds the electronic control board firmly in its designated mount or housing
• Helps prevent board movement, rattling, and connector stress from vibration
• Replace if the clip is cracked, deformed, or missing
• Symptoms include a loose control assembly, rattling noises, or a board that won't stay seated

• Disconnect power at the breaker before servicing
• Access the control area; support the board when removing/installing the clip
• Handle the control board by the edges and observe ESD precautions
• Ensure the new clip is fully seated and the board is secure before reassembly

This dielectric shield is a small heat-resistant insulator that protects ignition wiring and components from heat and prevents electrical arcing near burners. It helps maintain reliable spark ignition and reduces risk of shorts or damage from high temperatures. What it does:

• Shields spark module wires and electrode areas from direct heat exposure
• Helps prevent arcing and electrical shorts that can interrupt ignition
• Reduces risk of melted or damaged wire insulation near burners or ovens
• Commonly replaced when cracked, deformed, or showing burn marks that affect ignition

• Disconnect power (and gas if applicable) before servicing electrical or ignition components
• Inspect surrounding wiring and connectors; replace any damaged insulation or terminals
• Reinstall using original mounting hardware and ensure the shield fully covers the wire/electrode area

This right-side door trim is a factory-style replacement that restores the finished edge and appearance of the appliance door. It covers the door edge and trim mounting area for a clean, factory look. What it does

• Replaces cracked, chipped or worn right-side door trim to restore appearance
• Covers and protects the door edge and trim fasteners from dirt and damage
• Helps maintain the door's finished look after impacts or wear
• Fits into existing trim mounting points for a direct replacement

• High-level replacement only; follow for disassembly steps
• Remove any contents from the door and move shelves as needed for clearance
• Use proper tools to remove fasteners or trim clips; avoid forcing the trim to prevent damage

This top attachment strip secures the appliance's top panel and provides the mounting point for the door strike, restoring a stable, properly aligned front. It prevents panel movement and reduces rattles for a snug fit and reliable door engagement. What it does:

• Secures the top/front panel to the cabinet to maintain alignment and fit
• Serves as the mounting point for the door strike or latch components
• Helps eliminate rattling, vibration, and gaps at the top of the door area
• Restores reliable door engagement and prevents the strike from shifting

• Disconnect power to the appliance before beginning any repair
• Remove the top panel or access screws to reach the attachment strip; a screwdriver set is typically required
• Handle mounting tabs and edges carefully to avoid bending or damage
• Verify alignment of the door strike and test door closure after installation

This replacement screw fastens and secures appliance components where a 1/4-28 threaded flange screw with an internal hex washer head is required. It restores proper fit and helps prevent movement or rattling of panels and assemblies. What it does:

• Secures panels, brackets and components that use a 1/4-28 threaded flange screw
• Internal hex washer head allows a compact, low-profile drive for tight spaces
• Helps stop looseness, vibration noise, and misalignment when the original fastener is missing or worn
• Matches OEM fit and fastening form for reliable reassembly

• Disconnect power and follow all appliance safety procedures before servicing
• Use the correct hex driver/socket to avoid stripping the head
• Tighten to snug fit—do not overtighten to avoid damaging threads or mating parts
• Replace with identical part number to ensure proper fit and function

This small plastic clip secures a refrigerator's wiring conduit or harness to the cabinet, keeping wires routed and protected from abrasion. It helps reduce strain on connections and prevents wires from contacting moving parts. What it does:

• Holds wiring conduit or harness in place to maintain neat routing
• Prevents wires from rubbing on sharp edges or moving components
• Reduces strain on electrical connections that can cause intermittent faults
• Helps maintain safe separation between wiring and high-heat or mechanical areas

• Turn power off at the appliance and unplug before inspecting or replacing wiring clips
• Remove access panels only as needed to reach the clip; avoid stressing surrounding wires
• Snap the clip into the original mounting slot or replace any damaged fasteners for a secure fit
• If wires show damage or burns, replace the wiring/harness

This drain pump hanger secures the washer's drain pump to the outer tub, keeping the pump and hoses aligned so the pump can remove water reliably. Use it to replace a cracked or broken support that lets the pump shift. What it does

• Holds the drain pump firmly in place and maintains proper pump alignment.
• Helps reduce pump vibration and noise from a loose or mispositioned pump.
• Prevents the pump from pulling on hoses or becoming dislodged during the spin/drain cycle.
• A worn or broken hanger can contribute to poor draining, intermittent drainage, or unusual pump noise.

• One drain pump hanger.

• Disconnect power to the washer before beginning any repair.
• Access typically via the washer's lower front or rear panel; follow for disassembly.
• Inspect and reuse mounting hardware and grommets if undamaged; replace if corroded or broken.

This left-side door trim piece restores the exterior appearance and proper fit of a damaged or worn appliance door. It replaces cracked, chipped, or loose trim to help the door close and sit correctly in the frame. What it does:

• Covers and protects the left edge of the door while providing a finished appearance
• Replaces cracked, broken, or cosmetically damaged trim
• Helps maintain correct alignment of the door edge and attachment points
• Secures to the door with factory mounting tabs or screws
• Useful when left-side trim has snapped, warped, or come loose

• One left side door trim

• Disconnect power and/or fuel supply before beginning any repair
• Use appropriate hand tools; support the door to prevent dropping or damage
• Inspect mounting tabs and nearby components; replace any broken fasteners
• Follow the appliance service manual for disassembly and torque/spec guidance

This control box bottom is the lower housing that protects and supports the appliance's control electronics, helping keep wiring and components secure from debris and moisture. Fits into the control assembly to restore proper enclosure and support. What it does:

• Provides a protective lower enclosure for the control board and wiring harness
• Helps keep dust, lint and moisture away from sensitive electronics
• Secures the control board and related connectors in their correct position
• Prevents rattling or movement that can cause loose connections or noise

• One control box bottom (base cover) as pictured

• Disconnect power before servicing to avoid shock or component damage
• Handle electronics carefully and avoid touching circuit contacts
• Installation typically requires basic hand tools and removal of the control housing

The Filter Adapter is an OEM component specifically designed for GE dishwashers. Located inside the dishwasher tub, it functions to strain out large food particles from water before it reaches the wash arms.  The adapter holds the removable wash/rinse filters in place during operation, functioning as an extension of the filtration system. 

Causes of a bad filter adapter can include cracks or breaks compromising its sealing surface, wear and tear deforming filter retention features over time, or buildup inhibiting functionality.

Symptoms of a bad filter adapter include:  

• Loose or falling out removable filters during washing  
• Bypassing of food particles around compromised seals
• Reduced lifespan of disposable filters placed in a faulty adapter
• Debris accumulation impacting spray arm performance

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This bottle blaster assembly supplies targeted wash water to the dishwasher's Bottle Jets to clean tall, narrow items like baby and sports bottles. Replace a damaged or clogged assembly to restore focused spray and top-rack cleaning performance. What it does:

• Routes wash water to the bottle jet nozzles for concentrated cleaning inside bottles and narrow openings
• Helps improve cleaning on items positioned over the Bottle Jets
• Failure symptoms include no spray from the bottle jets, poor upper-rack cleaning, leaks near the jet area, or visible cracks/damage

• 1 bottle blaster assembly

• Disconnect power and shut off water to the dishwasher before servicing
• Access the bottle jet area; release retaining clips/fasteners and note hose routing and connection points
• Transfer any reusable clips or seals from the original assembly if needed
• Fully seat connections; run a short cycle to check for leaks and proper jet spray

This insulation toe kick is a replacement panel that fits the refrigerator base to help block drafts and protect internal components under the cabinet. It restores the factory barrier that supports temperature stability and efficient operation. What it does

• Replaces damaged or missing toe-kick insulation that lets cold air escape beneath the appliance
• Helps reduce drafts and minimize warm air intrusion into the refrigerator cavity
• Protects wiring and components located in the toe-kick area from dust and debris
• Can help prevent uneven cooling or frost buildup that results from compromised base insulation

• One insulation toe kick panel

• Disconnect power to the appliance before starting any service
• Remove the existing toe kick/board and fasteners, then position the replacement so mounting tabs align with factory slots
• Avoid compressing or tearing the insulation; maintain original fit for proper performance

This harness assembly routes AC power and control signals between components to restore electrical connectivity and reliable operation. Replaces a damaged or burned wiring harness to help eliminate intermittent power, no-start, or control faults. What it does:

• Provides the factory wiring connections for AC power and control circuits
• Replaces frayed, burnt, or disconnected wires that cause intermittent operation or no power
• Restores proper connector fit to ensure secure electrical contact
• Helps address symptoms such as appliance not starting, sporadic operation, or blown fuses/circuit breakers

• Disconnect power before servicing to avoid electrical shock
• Inspect connectors and mounting points; secure harness away from sharp edges and heat sources
• Match connector shapes and pin counts; do not force connectors together