Ge Gdt530pgd4ww Parts

This dishwasher main control board kit is the central circuit board that directs all wash functions. Replacing a failed board restores proper power distribution and timing so cycles start, advance, and finish correctly, helping prevent intermittent shutdowns and erratic operation. What it does:

• Controls cycle timing and communicates with sensors
• Distributes power to the wash motor, drain pump, inlet valve, and heater
• Works with the door latch and user interface to start/stop the cycle
• Failure may cause no power/won't start, stalled cycles, blinking lights/error codes, or incorrect filling, draining, or heating

• One main control board kit

• Disconnect power at the circuit breaker; turn off water if moving the dishwasher for access
• Board is typically in a housing beneath the unit—use ESD precautions and keep connections dry
• Photograph/label wire harnesses; transfer connectors one at a time to the new board
• Restore power and run a test or rinse cycle to proper operation

This leveling leg adjusts the dishwasher's height at the base, helping you level and stabilize the unit inside the cabinet. Proper leveling reduces rocking and vibration and promotes a tight door seal and smooth rack operation.

• Screws into the base frame to set height and level the dishwasher
• Supports the unit to prevent rocking or wobbling
• Helps maintain door alignment and sealing; poor leveling can contribute to leaks
• A worn, bent, or missing leg can make leveling difficult and increase vibration/noise

• Disconnect power and shut off water; slide the dishwasher out if needed for access
• Turn the leg with a wrench or pliers to adjust height; replace by threading the new leg into the base
• Use a bubble level to set side-to-side and front-to-back level before re-securing the unit
• Do not overtighten; ensure both legs carry weight evenly on a solid floor surface

The Vent Filter is an OEM part for GE dishwashers. It helps to capture and filter out food particles, grease, and other debris. 

Causes of a bad vent filter can include clogging or blockage due to accumulated debris, wear and tear over time, or damage to the filter material.

Symptoms of a bad vent filter include:

• Lingering unpleasant odors during or after the dishwasher cycle
• Visible signs of debris or buildup on the filter surface
• Reduced effectiveness of the dishwasher's drying performance

Replace your worn-out or clogged vent filter with this genuine OEM GE part to restore your dishwasher. 

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

Rack bracket with three wheels for the dishwasher rack. This assembly mounts to the rack and rides in the rail to keep the rack level and rolling smoothly, replacing cracked wheels or a damaged bracket to restore easy operation.

• Supports the rack and rolls along the rail on three wheels
• Restores smooth in-and-out rack movement
• Helps keep the rack aligned and prevents derailing or dropping
• Typical failure signs: cracked/broken wheels, damaged bracket, rack binding

• Disconnect power at the breaker; shut off water supply for safety
• Pull the rack out and remove any rail end caps/stops to access the bracket
• Release the old bracket and install the new one in the same orientation
• Reinstall stops, reseat the rack, and verify smooth travel

This dishwasher junction box cover encloses the power-connection compartment at the base of the unit. Replacing a damaged or missing cover helps protect wiring from debris and accidental contact, restoring a safe, secure connection area. What it does:

• Covers and secures the dishwasher's electrical junction box
• Helps shield wire splices from moisture, dust, and accidental contact
• Restores proper fit when the original cover is cracked, broken, or missing
• Useful if the junction box won't stay closed or the cover no longer secures properly

• Includes 1 junction box cover

• Disconnect power at the circuit breaker before servicing
• Remove the lower access/kick panel to reach the junction box
• Remove the old cover and screw, position the new cover, and secure with the existing hardware
• Ensure all wiring and the strain relief are fully inside the box before closing; restore power and test

This adapter plate is a molded interface in the wash system that secures and seals components so water pressure is routed correctly. Replacing a cracked or warped plate helps stop leaks and restore proper spray performance.

• Connects and supports wash-system components at the sump/water-feed interface
• Maintains a reliable seal to help prevent leaks
• Helps direct wash water to the spray arms for effective cleaning
• Replace if cracked, warped, or stripped; symptoms can include leaks, weak spray, or a loose spray arm

• Disconnect power and water supply before servicing
• Remove the lower rack and related wash components to access the plate; note the order of parts for reassembly
• Reuse existing seals and fasteners in their original positions; seat the plate evenly and tighten hardware snugly, not overtight
• Run a brief test cycle and inspect for leaks before full use

This dishwasher turbidity sensor assembly monitors water clarity in the sump and reports to the control so it can adjust wash time and rinses for optimal cleaning. Replacing a failed sensor can restore normal cycle decisions and performance.

• Measures wash-water clarity (soil/turbidity) and sends data to the control
• Helps optimize cycle length, number of rinses, and water usage
• A faulty sensor may cause unusually long or short cycles
• Can contribute to poor cleaning or failure to complete a cycle
• May set a sensor-related code in diagnostics on some models

• Disconnect power at the breaker and shut off water before servicing
• Access from the bottom/front of the dishwasher; place a towel to catch residual water
• Unplug the wire connector, rotate the sensor to unlock, and remove; ensure the seal seats properly when installing the new part
• After installation, check for leaks and run a test cycle

This clamp kit replaces worn Piranha-style clamps used in the dishwasher's wash system. Restores a tight, reliable seal on internal connections to help prevent leaks and maintain proper water circulation for consistent cleaning results.

• Secures internal hose and pump connections within the wash system
• Helps stop water leaks caused by loose, stretched, or damaged clamps
• Supports proper circulation and wash performance by keeping joints sealed
• Common symptoms: water under the unit, drips at hose joints, loose connections, vibration or rattling from the sump area

• Disconnect power and shut off the water supply before servicing
• Access the sump/pump area from the front toe-kick or by pulling the unit out as needed
• Replace one connection at a time; position and fully seat the new clamp(s) on clean hose/barb surfaces
• Restore power/water and run a short cycle to check carefully for leaks before reinstalling panels

This hose clamp kit secures the washer's hoses at the pump, tub, or valve connections, helping stop leaks and hose blow-offs. Replace worn or missing clamps to restore a tight, reliable seal during fill, wash, and drain.

• Secures drain, pump, and fill hoses to fittings to maintain a watertight seal
• Helps prevent drips, leaks, and hoses slipping off during vibration
• Replaces clamps that are rusted, stripped, deformed, or missing
• Common symptoms: water leaking at hose joints, loose hose connections, clamp won't tighten
• Useful when installing a new hose, pump, or valve

• Unplug the washer and turn off water supplies; have towels or a pan ready for residual water
• Release and remove old clamps; seat the hose fully over the fitting before installing new clamps
• Tighten evenly and do not overtighten to avoid hose or fitting damage
• Restore power and water, then run a short cycle to check for leaks at each connection

This is a machine screw used to secure dishwasher components. The 10-32 thread and 3/8-inch length with an integrated hex washer head provide a firm, vibration-resistant hold to keep parts properly fastened.

• Secures brackets, panels, or internal assemblies in the dishwasher
• Helps prevent looseness, rattling, or misalignment during operation
• Common symptoms of a missing/stripped screw include panel movement, vibration, or loose mounting points

• Disconnect power and shut off water before servicing
• Use the correct nut driver or socket to avoid stripping the head
• Replace any damaged or missing screws in matching locations
• Do not overtighten; snug to manufacturer's torque guidance when available

This fill funnel assembly mounts inside the dishwasher tub at the water inlet. It directs incoming water into the tub and helps prevent splashing or leaks at the fill area for reliable fills and cleaner operation.

• Channels water from the inlet opening directly into the tub
• Helps control splash and seal the fill port to reduce drips
• Damage, cracks, or a missing funnel can cause leaks near the fill area during the fill cycle or unusual spraying sounds
• Restores proper water entry path for consistent filling

• Disconnect power and shut off the water supply before servicing
• Remove the lower rack and locate the fill inlet on the tub wall
• Remove retaining fastener(s) or tabs, replace the funnel, and ensure any seal is properly seated
• Reassemble and run a brief fill/rinse to check for leaks at the inlet area

This dishwasher hose clamp secures a hose to its fitting to maintain a tight, leak-resistant seal during operation. Replacing a worn or corroded clamp helps stop drips and keeps fill, drain, or circulation lines firmly in place.

• Secures dishwasher hoses to fittings on pumps, valves, or drain outlets
• Helps prevent water leaks at hose connections
• Keeps hoses from slipping off under vibration and water pressure
• Typical symptoms include water under the unit, dampness in the cabinet, or a hose connection that feels loose

• Disconnect power and shut off water supply before servicing
• Access the hose connection (toe-kick or rear/side panels may need removal)
• Seat the hose fully on the fitting, position clamp just behind the barb/ridge, and secure without over-tightening
• Run a short test cycle and check all connections for leaks

This clip bracket attaches to the dishwasher rack to secure a rack-mounted component or accessory. Replace a cracked or missing bracket to keep parts firmly in place so the rack loads easily and performs as designed.

• Attaches to the rack to hold the mating part securely in place
• Helps prevent shifting, rattling, or accessories falling off during cycles
• Restores proper fit when the original clip is broken, worn, or missing
• Typical signs: accessory won't stay attached, clip is visibly cracked or missing, loose components during operation

• Disconnect power at the breaker and turn off the water supply
• Pull out the rack to access the clip location
• Release the old clip's locking tabs and remove; align and snap the new clip firmly in place
• Verify a secure fit before reinstalling the rack and running a test cycle

This top-control console is the panel at the upper edge of the dishwasher door. It forms the interface area for selecting cycles and protects the components behind it, helping keep the controls aligned and presentable.

• Houses and protects the user interface at the top edge of the door
• Provides the interface area for cycle and option selection
• Restores fit and appearance when the original console is cracked, warped, or loose
• Help if buttons feel misaligned due to a damaged console housing

• Disconnect power at the breaker before servicing; shut off water if moving the appliance.
• Open the door and remove perimeter screws to separate inner/outer door panels; support wiring when removing the console.
• Transfer any model-specific components from the original console to the new console; avoid pinching harnesses during reassembly.
• Restore power and selections engage and the door latches properly.

Size: 10-32 GXTT FLP.595 S